SIST EN ISO 18183-3:2024
(Main)Geometrical product specifications (GPS) - Partition - Part 3: Methods used for specification and verification (ISO 18183-3:2024)
Geometrical product specifications (GPS) - Partition - Part 3: Methods used for specification and verification (ISO 18183-3:2024)
This document sets out the procedure (or process) for the partition operations of Geometrical Product Specification and Verification. Profile and Areal surface texture are not within the scope of this document.
Geometrische Produktspezifikation (GPS) - Partition - Teil 3: Verfahren für die Spezifikation und Verifikation (ISO 18183-3:2024)
Dieses Dokument legt das Verfahren für die Partitionsoperation der geometrischen Produktspezifikation und Verifikation fest.
Dieses Dokument gilt nicht für die profilhafte Oberflächenbeschaffenheit und die flächenhafte Oberflächenbeschaffenheit.
Spécification géométrique des produits (GPS) - Partition - Partie 3: Méthodes utilisées pour la spécification et la vérification (ISO 18183-3:2024)
Le présent document spécifie le mode opératoire de l'opération de partition de la spécification et vérification géométriques des produits.
Le présent document ne s'applique pas au profil et à l'état de surface surfacique.
Specifikacija geometrijskih veličin izdelka (GPS) - Razdelitev - 3. del: Metode za specifikacijo in preverjanje (ISO 18183-3:2024)
Ta dokument določa postopek (ali proces) za operacije razdelitve specifikacije in preverjanja geometrijskih veličin izdelka. Področje uporabe tega dokumenta ne zajema profilnih in ploskovnih tekstur površine.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 18183-3:2024
01-april-2024
Specifikacija geometrijskih veličin izdelka (GPS) - Razdelitev - 3. del: Metode za
specifikacijo in preverjanje (ISO 18183-3:2024)
Geometrical product specifications (GPS) - Partition - Part 3: Methods used for
specification and verification (ISO 18183-3:2024)
Geometrische Produktspezifikation (GPS) - Partition - Teil 3: Verfahren für die
Spezifikation und Verifikation (ISO 18183-3:2024)
Spécification géométrique des produits (GPS) - Partition - Partie 3: Méthodes utilisées
pour la spécification et la vérification (ISO 18183-3:2024)
Ta slovenski standard je istoveten z: EN ISO 18183-3:2024
ICS:
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 18183-3:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 18183-3:2024
---------------------- Page: 2 ----------------------
SIST EN ISO 18183-3:2024
EN ISO 18183-3
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2024
EUROPÄISCHE NORM
ICS 17.040.40
English Version
Geometrical product specifications (GPS) - Partition - Part
3: Methods used for specification and verification (ISO
18183-3:2024)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) - Partition -
Partition - Partie 3: Méthodes utilisées pour la Teil 3: Verfahren für die Spezifikation und Verifikation
spécification et la vérification (ISO 18183-3:2024) (ISO 18183-3:2024)
This European Standard was approved by CEN on 20 January 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18183-3:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 18183-3:2024
EN ISO 18183-3:2024 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 18183-3:2024
EN ISO 18183-3:2024 (E)
European foreword
This document (EN ISO 18183-3:2024) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2024, and conflicting national standards shall
be withdrawn at the latest by August 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.