SIST ISO 6526:2020

Plain bearings - Pressed bimetallic half thrust washers - Features and tolerances

ISO 6526 specifies the main features and tolerances for pressed bimetallic half thrust washers having an outside diameter up to 160 mm.

Paliers lisses - Demi-flasques de butée bimétalliques découpés à la presse - Caractéristiques et tolérances

Drsni ležaji - Stiskane kovinske dvoslojne oporne podloge - Oblika in tolerance

General Information

• Status: Published
• Publication Date: 03-Mar-2020
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 02-Mar-2020
• Due Date: 07-May-2020
• Completion Date: 04-Mar-2020
• Ref Project: ISO 6526:2017 - Plain bearings — Pressed bimetallic half thrust washers — Features and tolerances

Relations

• Replaces: SIST ISO 6526:2002 - Plain bearings -- Pressed bimetallic half thrust washers -- Features and tolerances
• Effective Date: 02-Mar-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6526
Second edition
2017-10
Plain bearings — Pressed bimetallic
half thrust washers — Features and
tolerances
Paliers lisses — Demi-flasques de butée bimétalliques découpés à la
presse — Caractéristiques et tolérances
Reference number
ISO 6526:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 6526:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6526:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 General tolerances . 4
6 Tolerances for diameters and for heights . 4
7 Total thickness . 5
8 Locating lug . 5
8.1 Lug width . 5
8.2 Notch recess . 6
8.3 Lug length . 6
9 Grooves . 6
9.1 Groove width . 6
9.2 Wall thickness at the back of the groove . 6
9.3 Groove position (with respect to the axis) . 6
10 Joint faces . 6
11 Fillet radii and chamfers . 7
11.1 Radius on lug and joint faces and lug fillet radius . 7
11.2 Joint face relief . 7
11.3 Chamfer or radius between the sliding surface and side faces . 7
11.4 Chamfer or radius between back and external side face . 7
12 Flatness . 7
13 Surface roughness . 8
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6526:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This secon
...

SLOVENSKI STANDARD
SIST ISO 6526:2020
01-april-2020
Nadomešča:
SIST ISO 6526:2002
Drsni ležaji - Stiskane kovinske dvoslojne oporne podloge - Oblika in tolerance
Plain bearings - Pressed bimetallic half thrust washers - Features and tolerances
Paliers lisses - Demi-flasques de butée bimétalliques découpés à la presse -
Caractéristiques et tolérances
Ta slovenski standard je istoveten z: ISO 6526:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 6526:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 6526:2020

---------------------- Page: 2 ----------------------
SIST ISO 6526:2020
INTERNATIONAL ISO
STANDARD 6526
Second edition
2017-10
Plain bearings — Pressed bimetallic
half thrust washers — Features and
tolerances
Paliers lisses — Demi-flasques de butée bimétalliques découpés à la
presse — Caractéristiques et tolérances
Reference number
ISO 6526:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 6526:2020
ISO 6526:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 6526:2020
ISO 6526:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 General tolerances . 4
6 Tolerances for diameters and for heights . 4
7 Total thickness . 5
8 Locating lug . 5
8.1 Lug width . 5
8.2 Notch recess . 6
8.3 Lug length . 6
9 Grooves . 6
9.1 Groove width . 6
9.2 Wall thickness at the back of the groove . 6
9.3 Groove position (with respect to the axis) . 6
10 Joint faces . 6
11 Fillet radii and chamfers . 7
11.1 Radius on lug and joint faces and lug fillet radius . 7
11.2 Joint face relief . 7
11.3 Chamfer or radius between the sliding surface and side faces . 7
11.4 Chamfer or radius between back and external side face . 7
12 Flatness . 7
13 Surface roughness . 8
© ISO 2017 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 6526:2020
ISO 6526:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
...