SIST EN 14187-4:2017
(Main)Cold applied joint sealants - Test methods - Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals
Cold applied joint sealants - Test methods - Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals
This European Standard describes a test method of the evaluation of the resistance of cold applied joint sealants to the action of liquid chemicals by measuring the change in mass and volume after immersion in test fuels and in liquid chemicals.
Kalt verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der Massen- und Volumenänderung nach Lagerung in Prüfkraftstoff
Diese Europäische Norm beschreibt ein Prüfverfahren zur Bewertung der Beständigkeit kalt verarbeitbarer Fugenmassen bei Einwirkung von flüssigen Chemikalien durch Messung der Massen- und der Volumenänderung nach Lagerung in Prüfkraftstoffen und in flüssigen Chemikalien.
Mastics pour joints appliqués à froid - Méthodes d'essai - Partie 4: Détermination de la variation de masse et de volume après immersion dans des carburants d'essai et des produits chimiques liquides
La présente Norme européenne décrit une méthode d'essai pour l'évaluation de la résistance des mastics pour joints appliqués à froid à l'action des produits chimiques liquides en mesurant la variation de masse et de volume après immersion dans des carburants d'essai et des produits chimiques liquides.
Hladno nanosljive tesnilne mase za stike - Preskusne metode - 4. del: Ugotavljanje spremembe mase in prostornine po namakanju v preskusnem gorivu in tekočih kemikalijah
Ta evropski standard opisuje preskusno metodo za vrednotenje odpornosti hladno nanosljivih tesnilnih mas za stike proti delovanju tekočih kemikalij z merjenjem spremembe mase in prostornine po namakanju v preskusnem gorivu ter tekočih kemikalijah.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.NHPLNDOLMDKKalt verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der Massen- und Volumenänderung nach Lagerung in PrüfkraftstoffMastics pour joints appliqués à froid - Méthodes d'essai - Partie 4: Détermination de la variation de masse et de volume après immersion dans des carburants d'essai et des produits chimiques liquidesCold applied joint sealants - Test methods - Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 14187-4:2017SIST EN 14187-4:2017en,fr,de01-maj-2017SIST EN 14187-4:2017SLOVENSKI
STANDARDSIST EN 14187-4:20041DGRPHãþD
SIST EN 14187-4:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14187-4
March
t r s y ICS
{ uä r z rä t r Supersedes EN
s v s z yæ vã t r r uEnglish Version
Cold applied joint sealants æ Test methods æ Part
vã Determination of the change in mass and volume after immersion in test fuels and liquid chemicals Mastics pour joints appliqués à froid æ Méthodes d 5essai æ Partie
v ã Détermination de la variation de masse et de volume après immersion dans des carburants d 5essai et des produits chimiques liquides
Kalt verarbeitbare Fugenmassen æ Prüfverfahren æ Teil
vã Bestimmung der Massenæ und Volumenänderung nach Lagerung in Prüfkraftstoffen und flüssigen Chemikalien This European Standard was approved by CEN on
x February
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v s z yæ vã t r s y ESIST EN 14187-4:2017
EN 14187-4:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus and materials . 4 6 Preparation of test specimens . 5 7 Conditioning . 5 8 Procedure. 5 8.1 Temperature of immersion . 5 8.2 Time of immersion . 6 8.3 Test procedure . 6 9 Expression of results . 6 9.1 Change in volume . 6 9.2 Change in mass after drying . 7 10 Test report . 7 Annex A (informative)
List of liquid chemicals . 8
SIST EN 14187-4:2017
EN 14187-4:2017 (E) 3 European foreword This document (EN 14187-4:2017) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14187-4:2003. Apart from editorial changes the following major changes have been made in this revision: a) Change of the title; b) Table 1, Change of the test fuels and addition of de-icing liquids in accordance with new technical requirements. This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants — Test methods — Part 1: Determination of rate of cure. EN 14187-2, Cold applied joint sealants — Test methods — Part 2: Determination of tack free time. EN 14187-3, Cold applied joint sealants — Test methods — Part 3: Determination of self-levelling properties. EN 14187-4, Cold applied joint sealants — Test methods — Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals. EN 14187-5, Cold applied joint sealants — Test methods — Part 5: Determination of the resistance to hydrolysis. EN 14187-6, Cold applied joint sealants — Test methods — Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals. EN 14187-7, Cold applied joint sealants — Test methods — Part 7: Determination of the resistance to flame. EN 14187-8, Cold applied joint sealants — Test methods — Part 8: Determination of resistances to artificial weathering by UV-irradiation. EN 14187-9, Cold applied joint sealants — Test methods — Part 9: Function testing of joint sealants. WARNING — Attention is drawn to the health and safety at work and the need to ensure that this test is carried out under suitable environmental conditions to provide adequate protection to persons against the risk of contact or inhalation of toxic liquid chemicals. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14187-4:2017
EN 14187-4:2017 (E) 4 1 Scope This European Standard describes a test method for determining the resistance of cold applied joint sealants to the action of liquid chemicals by measuring the change in mass and volume after immersion in test fuels or in liquid chemicals. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated ref
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.