SIST EN 13880-3:2024
(Main)Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience)
Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience)
This document describes a test method as an indicator both for the penetration resistance (hardness) and elastic recovery after de-loading (resilience) of hot applied joint sealants according to EN 14188-1 at 25 °C using a standard penetrometer fitted with a ball penetration tool.
Heiß verarbeitbare Fugenmassen - Teil 3: Prüfverfahren zur Bestimmung der Kugel-Penetration und des elastischen Rückstellvermögens
Dieses Dokument beschreibt ein Prüfverfahren als Indikator für den Eindringwiderstand (Härte) und das elastische Rückstellvermögen nach Entfernen der Last (Resilienz) von heiß verarbeitbaren Fugenmassen nach EN 14188-1 bei 25 °C mit Hilfe eines mit einem kugelförmigen Eindringkörper ausgerüsteten genormten Penetrometers.
Produits de scellement de joints appliqués à chaud - Partie 3 : Méthode d'essais pour la détermination de la pénétrabilité et du retour élastique
Ce document décrit une méthode d'essai servant d'indicateur à la fois pour la résistance à la pénétration (dureté) et la récupération élastique après déchargement (résilience) des mastics de joints appliqués à chaud selon la norme EN 14188 -1 à 25 °C en utilisant un pénétromètre standard équipé d'un outil de pénétration à bille.
Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 3. del: Preskusna metoda za ugotavljanje penetracije in sposobnosti vrnitve v prvotno stanje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN 13880-3:2004
Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 3. del: Preskusna
metoda za ugotavljanje penetracije in sposobnosti vrnitve v prvotno stanje
Hot applied joint sealants - Part 3: Test method for the determination of penetration and
recovery (resilience)
Heiß verarbeitbare Fugenmassen - Teil 3: Prüfverfahren zur Bestimmung der Kugel-
Penetration und des elastischen Rückstellvermögens
Produits de scellement de joints appliqués à chaud - Partie 3 : Méthode d'essais pour la
détermination de la pénétrabilité et du retour élastique
Ta slovenski standard je istoveten z: EN 13880-3:2024
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13880-3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 93.080.20 Supersedes EN 13880-3:2003
English Version
Hot applied joint sealants - Part 3: Test method for the
determination of penetration and recovery (resilience)
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 3:
Partie 3 : Méthode d'essais pour la détermination de la Prüfverfahren zur Bestimmung der Kugel-Penetration
pénétrabilité et du retour élastique und des elastischen Rückstellvermögens
This European Standard was approved by CEN on 24 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13880-3:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 6
5.1 Penetrometer . 6
5.2 Ball penetration tool . 6
5.3 Water bath . 7
5.4 Sample tins . 7
5.5 Time recording equipment . 7
6 Preparation and conditioning of the test specimens . 7
7 Test conditions . 7
8 Procedure . 7
9 Precision . 8
10 Test report . 9
Bibliography . 10
European foreword
This document (EN 13880-3:2024) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards shall
be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13880-3:2003.
— clarification of the test to improve the performance of the test method.
This document is one part of the EN 13880 series of standards, Hot applied joint sealants, which consists
of the following parts:
— Part 1: Test method for the determination of density at 25 °C.
— Part 2: Test method for the determination of cone penetration at 25 °C.
— Part 3: Test method for the determination of penetration and recovery (resilience).
— Part 4: Test method for the determination of heat resistance - Change in penetration value.
— Part 5: Test method for the determination of flow resistance.
— Part 6: Method for the preparation of samples for testing.
— Part 7: Function testing of joint sealants.
— Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after
fuel immersion.
— Part 9: Test method for the determination of compatibility with asphalt pavements.
— Part 10: Test method for the determination of adhesion and cohesion following continuous extension
and compression.
— Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the
determination of compatibility with asphalt pavements.
— Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods).
— Part 13: Test method for the determination of the discontinuous extension (adherence test).
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This docume
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.