Abstract

This document specifies minimum requirements applicable to design, final assessment, designation, marking and documentation for diaphragm valves:
-   having unlined and lined metallic bodies;
-   having weir, weirless and straight-through body designs;
-   for operation with manual handwheel or actuator;
-   for use with flanged, welded and threaded pipe end connections;
-   used for isolating, regulating or controlling applications or any combination thereof.
The PN and Class ranges are:
-   PN 6, PN 10, PN 16 and PN 25;
-   Class 125 and Class 150.
The size range is:
-   for flanged valves: sizes DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 450 and DN 500;
-   for screwed valves: sizes NPS ¼, ⅜, ½, ¾, 1, 1¼, 1½, 2, 2½ and 3;
-   for weld end valves: sizes DN 8, DN 10, DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150 and DN 200.
NOTE 1   Sizes are listed in Table D.1.
This document applies to metallic diaphragm valves used for all industrial applications.
For applications in accordance with the European legislation for pressure equipment, EN 16668:2025 applies together with this document.
Additional requirements given in the relevant application standards can apply to diaphragm valves used for more specific applications (e.g. for the water industry, the chemical and petrochemical process industry).
For chemical and petrochemical applications, EN 12569:2020 apply together with this document.
For water supply applications, EN 1074-1:2000 and EN 1074-2:2000 apply together with this document.
NOTE 2   National potable water approval schemes (WRAS, DVGW, ACS, etc.) can apply in addition to the valve design standards.
For process control applications, EN 1349:2009 and EN 60534-2-1:2011 apply together with this document.
For cryogenic applications, EN 1626:2008 apply together with this document.
For fire-safe applications, EN ISO 10497:2022 apply together with this document.
For fugitive emissions applications, EN ISO 15848-1:2015+A1:2017 and EN ISO 15848-2:2015 apply together with this document.
Other specific application standards, regulatory requirements, purchaser specifications or national approval schemes can also exist and can apply depending on the intended service, installation location, fluid, pressure/temperature conditions and end-use application.
The correspondence between DN and NPS is given for information in Annex C.

Status
Not Published
Public Enquiry End Date
02-Jan-2027
Technical Committee
TLP - Pressure vessels
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
13-Oct-2026
Due Date
02-Mar-2027

Buy Documents

Draft

oSIST prEN 13397:2026

English language (34 pages)
Preview
Preview
e-Library read for
×1 day

Relations

Effective Date
01-Dec-2026

Buy Documents

Draft

oSIST prEN 13397:2026

English language (34 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

Institut za varilstvo d.o.o. (Welding Institute)

Slovenia's leading welding institute since 1952. ISO 3834, EN 1090, pressure equipment certification, NDT personnel, welder qualification. Only IIW Au

SA Slovenia Verified

Sponsored listings

Frequently Asked Questions

oSIST prEN 13397:2026 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Industrial valves - Metallic diaphragm valves". This standard covers: This document specifies minimum requirements applicable to design, final assessment, designation, marking and documentation for diaphragm valves: - having unlined and lined metallic bodies; - having weir, weirless and straight-through body designs; - for operation with manual handwheel or actuator; - for use with flanged, welded and threaded pipe end connections; - used for isolating, regulating or controlling applications or any combination thereof. The PN and Class ranges are: - PN 6, PN 10, PN 16 and PN 25; - Class 125 and Class 150. The size range is: - for flanged valves: sizes DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 450 and DN 500; - for screwed valves: sizes NPS ¼, ⅜, ½, ¾, 1, 1¼, 1½, 2, 2½ and 3; - for weld end valves: sizes DN 8, DN 10, DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150 and DN 200. NOTE 1 Sizes are listed in Table D.1. This document applies to metallic diaphragm valves used for all industrial applications. For applications in accordance with the European legislation for pressure equipment, EN 16668:2025 applies together with this document. Additional requirements given in the relevant application standards can apply to diaphragm valves used for more specific applications (e.g. for the water industry, the chemical and petrochemical process industry). For chemical and petrochemical applications, EN 12569:2020 apply together with this document. For water supply applications, EN 1074-1:2000 and EN 1074-2:2000 apply together with this document. NOTE 2 National potable water approval schemes (WRAS, DVGW, ACS, etc.) can apply in addition to the valve design standards. For process control applications, EN 1349:2009 and EN 60534-2-1:2011 apply together with this document. For cryogenic applications, EN 1626:2008 apply together with this document. For fire-safe applications, EN ISO 10497:2022 apply together with this document. For fugitive emissions applications, EN ISO 15848-1:2015+A1:2017 and EN ISO 15848-2:2015 apply together with this document. Other specific application standards, regulatory requirements, purchaser specifications or national approval schemes can also exist and can apply depending on the intended service, installation location, fluid, pressure/temperature conditions and end-use application. The correspondence between DN and NPS is given for information in Annex C.

This document specifies minimum requirements applicable to design, final assessment, designation, marking and documentation for diaphragm valves: - having unlined and lined metallic bodies; - having weir, weirless and straight-through body designs; - for operation with manual handwheel or actuator; - for use with flanged, welded and threaded pipe end connections; - used for isolating, regulating or controlling applications or any combination thereof. The PN and Class ranges are: - PN 6, PN 10, PN 16 and PN 25; - Class 125 and Class 150. The size range is: - for flanged valves: sizes DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 450 and DN 500; - for screwed valves: sizes NPS ¼, ⅜, ½, ¾, 1, 1¼, 1½, 2, 2½ and 3; - for weld end valves: sizes DN 8, DN 10, DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125, DN 150 and DN 200. NOTE 1 Sizes are listed in Table D.1. This document applies to metallic diaphragm valves used for all industrial applications. For applications in accordance with the European legislation for pressure equipment, EN 16668:2025 applies together with this document. Additional requirements given in the relevant application standards can apply to diaphragm valves used for more specific applications (e.g. for the water industry, the chemical and petrochemical process industry). For chemical and petrochemical applications, EN 12569:2020 apply together with this document. For water supply applications, EN 1074-1:2000 and EN 1074-2:2000 apply together with this document. NOTE 2 National potable water approval schemes (WRAS, DVGW, ACS, etc.) can apply in addition to the valve design standards. For process control applications, EN 1349:2009 and EN 60534-2-1:2011 apply together with this document. For cryogenic applications, EN 1626:2008 apply together with this document. For fire-safe applications, EN ISO 10497:2022 apply together with this document. For fugitive emissions applications, EN ISO 15848-1:2015+A1:2017 and EN ISO 15848-2:2015 apply together with this document. Other specific application standards, regulatory requirements, purchaser specifications or national approval schemes can also exist and can apply depending on the intended service, installation location, fluid, pressure/temperature conditions and end-use application. The correspondence between DN and NPS is given for information in Annex C.

oSIST prEN 13397:2026 is classified under the following ICS (International Classification for Standards) categories: 23.060.01 - Valves in general. The ICS classification helps identify the subject area and facilitates finding related standards.

oSIST prEN 13397:2026 has the following relationships with other standards: It is inter standard links to SIST EN 13397:2002. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

oSIST prEN 13397:2026 is associated with the following European legislation: EU Directives/Regulations: 2014/68/EU; Standardization Mandates: M/071, M/601. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

oSIST prEN 13397:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2026
Industrijski ventili - Membranski ventili s kovinsko membrano
Industrial valves - Metallic diaphragm valves
Industriearmaturen - Membranarmaturen aus Metall
Robinetterie industrielle - Robinets métalliques à membrane
Ta slovenski standard je istoveten z: prEN 13397
ICS:
23.060.01 Ventili na splošno Valves in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2026
ICS 23.060.01 Will supersede EN 13397:2001
English Version
Industrial valves - Metallic diaphragm valves
Robinetterie industrielle - Robinets métalliques à Industriearmaturen - Membranarmaturen aus Metall
membrane
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 69.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13397:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 9
4 Design requirements . 10
4.1 General . 10
4.2 Shell . 13
4.3 Body . 13
4.3.1 General . 13
4.3.2 End connections . 14
4.4 Obturator (diaphragm) . 14
4.5 Bonnet . 14
4.6 Stem, compressor and other working parts . 14
4.7 Optional design features . 14
4.8 Materials . 15
4.8.1 Shell materials . 15
4.8.2 Body and bonnet bolting material . 15
4.8.3 Body lining (if applicable) . 15
4.8.4 Corrosion protection. 15
4.8.5 Diaphragm materials . 16
4.9 Pressure/temperature ratings . 16
4.10 Dimensions and tolerances . 16
4.10.1 Face-to-face and end-to-end dimensions . 16
4.10.2 Body, flanged end . 17
4.10.3 Body, butt and socket welding end . 17
4.10.4 Body, threaded end . 17
4.10.5 Body, other types of ends . 17
4.11 Operation . 17
4.11.1 Operational capability . 17
4.11.2 Manual or power operating device . 18
4.12 Manufacturing . 18
4.12.1 Welding . 18
4.12.2 Non-destructive testing (NDT) of joint welding . 19
4.12.3 Heat treatment . 19
4.12.4 Traceability . 19
4.13 Functional characteristics and performances . 19
4.13.1 Application . 19
4.13.2 Seat leakage . 19
4.13.3 Flow characteristics . 19
4.14 Additional requirements for diaphragm valves classified as pressure accessories in
accordance with EN 16668:2025 . 19
4.15 Additional requirements for diaphragm valves intended to be used in other
applications . 19
5 Final assessment . 20
6 Designation . 21
7 Marking and preparation for storage and transportation . 21
7.1 Marking . 21
7.1.1 Mandatory marking . 21
7.1.2 Supplementary marking . 21
7.1.3 Omission of marking . 22
7.2 Preparation for storage and transportation . 22
8 Documentation . 22
8.1 General . 22
8.2 Operating instructions . 23
Annex A (informative) Valve data sheet . 24
Annex B (informative) Environmental corrosion protection . 27
Annex C (informative) Correspondence between DN and NPS . 28
Annex D (informative) Relationship between this document and EN 16668:2025 . 29
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/68/EU (Pressure Equipment Directive) aimed to be
covered . 31
Bibliography . 33
European foreword
This document (prEN 13397:2026) has been prepared by Technical Committee CEN/TC 69 “Industrial
valves”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13397:2001.
This document includes the following significant technical changes with respect to EN 13397:2001:
a) inclusion of an introduction to explain the reason of this revision;
b) the inclusion of a sentence in the scope to clarify that this document applies to all industrial
applications;
c) addition of new 4.14 and 5.2 on the design requirements and final assessment for the European
legislation for pressure equipment;
d) addition of a new Clause 8 for the documentation;
e) removal of shell materials table in Annex A;
f) update of Annex A to provide valve data sheet template;
g) addition of Annex B providing details on environmental corrosion protection;
h) addition of Annex C providing correspondence between DN and NPS;
i) addition of Annex D providing the relationship between the clauses/subclauses of this document and
those of EN 16668:2025;
j) update of Annex ZA.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Introduction
This document was revised to refer to EN 16668:2025 for those requirements related to the European
legislation for pressure equipment applicable to diaphragm valves.
EN 16668:2025 was drafted to cover the requirements for the European legislation on Pressure
Equipment. Therefore, for the applications in accordance with the European legislation for pressure
equipment, EN 16668:2025 applies together with this document.
Annex D provides the relationship between the clauses/subclauses of this document and those of
EN 16668:2025.
NOTE Annex ZA of this document is identical to Annex ZA of EN 16668:2025, for those requirements
applicable to diaphragm valves.
1 Scope
This document specifies minimum requirements applicable to design, final assessment, designation,
marking and documentation for diaphragm valves:
— having unlined and lined metallic bodies;
— having weir, weirless and straight-through body designs;
— for operation with manual handwheel or actuator;
— for use with flanged, welded and threaded pipe end connections;
— used for isolating, regulating or controlling applications or any combination thereof.
The PN and Class ranges are:
— PN 6, PN 10, PN 16 and PN 25;
— Class 125 and Class 150.
The size range is:
— for flanged valves: sizes DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80, DN 100, DN 125,
DN 150, DN 200, DN 250, DN 300, DN 350, DN 400, DN 450 and DN 500;
— for screwed valves: sizes NPS ¼, ⅜, ½, ¾, 1, 1¼, 1½, 2, 2½ and 3;
— for weld end valves: sizes DN 8, DN 10, DN 15, DN 20, DN 25, DN 32, DN 40, DN 50, DN 65, DN 80,
DN 100, DN 125, DN 150 and DN 200.
NOTE 1 Sizes are listed in Table D.1.
This document applies to metallic diaphragm valves used for all industrial applications.
For applications in accordance with the European legislation for pressure equipment, EN 16668:2025
applies together with this document.
Additional requirements given in the relevant application standards can apply to diaphragm valves used
for more specific applications (e.g. for the water industry, the chemical and petrochemical process
industry).
For chemical and petrochemical applications, EN 12569:2020 apply together with this document.
For water supply applications, EN 1074-1:2000 and EN 1074-2:2000 apply together with this document.
NOTE 2 National potable water approval schemes (WRAS, DVGW, ACS, etc.) can apply in addition to the valve
design standards.
For process control applications, EN 1349:2009 and EN 60534-2-1:2011 apply together with this
document.
For cryogenic applications, EN 1626:2008 apply together with this document.
For fire-safe applications, EN ISO 10497:2022 apply together with this document.
For fugitive emissions applications, EN ISO 15848-1:2015+A1:2017 and EN ISO 15848-2:2015 apply
together with this document.
Other specific application standards, regulatory requirements, purchaser specifications or national
approval schemes can also exist and can apply depending on the intended service, installation location,
fluid, pressure/temperature conditions and end-use application.
The correspondence between DN and NPS is given for information in Annex C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 19:2023, Industrial valves — Marking of metallic valves
EN 558:2022, Industrial valves — Face-to-face and centre-to-face dimensions of metal valves for use in
flanged pipe systems — PN and Class designated valves
EN 736-1:2018, Valves — Terminology — Part 1: Definition of types of valves
EN 736-2:2016, Valves — Terminology — Part 2: Definition of components of valves
EN 736-3:2008, Valves — Terminology — Part 3: Definition of terms
EN 764-1:2015+A1:2016, Pressure equipment — Part 1: Vocabulary
EN 1074-2:2000, Valves for water supply — Fitness for purpose requirements and appropriate verification
tests — Part 2: Isolating valves
EN 1092-1:2018, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 1: Steel flanges
EN 1092-2:2023, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 2: Cast iron flanges
EN 1092-3:2003, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 3: Copper alloy flanges
EN 1092-4:2002, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 4: Aluminium alloy flanges
EN 1267:2012, Industrial valves — Test of flow resistance using water as test fluid
EN 1349:2009, Industrial process control valves
EN 1626:2008, Cryogenic vessels — Valves for cryogenic service
EN 1759-1:2004, Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 1: Steel flanges, NPS 1/2 to 24
EN 1759-3:2003, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, Class
designated — Part 3: Copper alloy flanges

Document impacted by EN 1074-2:2000/A1:2004.
EN 1759-4:2003, Flanges and their joint — Circular flanges for pipes, valves, fittings and accessories, class
designated — Part 4: Aluminium alloy flanges
EN 10226-1:2004, Pipe threads where pressure tight joints are made on the threads — Part 1: Taper
external threads and parallel internal threads — Dimensions, tolerances and designation
EN 10269:2013, Steels and nickel alloys for fasteners with specified elevated and/or low temperature
properties
EN 12266-1:2012, Industrial valves — Testing of metallic valves — Part 1: Pressure tests, test procedures
and acceptance criteria — Mandatory requirements
EN 12266-2:2012, Industrial valves — Testing of metallic valves — Part 2: Tests, test procedures and
acceptance criteria — Supplementary requirements
EN 12516-1:2014+A1:2018, Industrial valves — Shell design strength — Part 1: Tabulation method for
steel valve shells
EN 12516-2:2014+A1:2021, Industrial valves — Shell design strength — Part 2: Calculation method for
steel valve shells
EN 12516-3:2002, Valves — Shell design strength — Part 3: Experimental method
EN 12516-4:2014+A1:2018, Industrial valves — Shell design strength — Part 4: Calculation method for
valve shells manufactured in metallic materials other than steel
EN 12570:2000, Industrial valves — Method for sizing the operating element
EN 12569:2020, Industrial valves — Valves for chemical and petrochemical process industry —
Requirements and tests
EN 12627:2017, Industrial valves — Butt welding ends for steel valves
EN 12760:2016, Industrial valves — Socket welding ends for steel valves
EN 12982:2009, Industrial valves — End-to-end and centre-to-end dimensions for butt welding end valves
EN 16668:2025, Industrial valves — Requirements and testing for metallic valves as pressure accessories
EN 16722:2015, Industrial valves — End-to-end and centre-to-end dimensions for valves with threaded
ends
EN 60534-2-3:2016, Industrial-process control valves — Part 2-3: Flow capacity — Test procedures
(IEC 60534-2-3:2016)
EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads — Part 1:
Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 1043-1:2011, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics (ISO 1043-1:2011)
EN ISO 5210:2026, Industrial valves — Multi-turn actuator attachments (ISO 5210:2026)
EN ISO 10497:2022, Testing of valves — Fire type-testing requirements (ISO 10497:2022)
ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 1629:2025, Rubber and lattices — Nomenclature
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 736-1:2018, EN 736-2:2016,
EN 736-3:2008 and EN 764-1:2015+A1:2016, and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
weir type diaphragm valve
valve in which closure is attained by compression of the diaphragm onto a raised weir formed in the body
shape
[SOURCE: EN 736-1:2018, 4.1.6]
3.2
straight through type diaphragm valve
valve in which closure is attained by compression of the diaphragm onto the valve body wall, the body
maintaining a largely straight-through bore configuration
[SOURCE: EN 736-1:2018, 4.1.6]
3.3
maximum allowable pressure
PS
maximum pressure for which the pressure equipment is designed
[SOURCE: EN 764-1:2015+A1:2016, 3.2.87]
3.4
maximum allowable temperature
TS
max
maximum temperature for which the pressure equipment is designed
[SOURCE: EN 764-1:2015+A1:2016, 3.1.9]
3.5
end of line service
condition that occurs when the downstream side of the valve is opened to atmosphere
3.6
diaphragm
flexible component, generally of either elastomeric or polymeric material, which does not form part of
the pressure bearing shell but acts as the valve obturator, whilst also isolating the valve mechanism from
the line fluid
[SOURCE: EN 736-2:2016, 3.3.10]
3.7
compressor
component of the diaphragm valve assembly which affords compression to the diaphragm to effect
closure against the valve body
3.8
bonnet bolting
bolting which connects the bonnet to the body
[SOURCE: EN 736-2:2016, 3.1.3.5]
3.9
manual actuation
means to operate a valve by human power source for example, via handwheel
3.10
power actuation
means to operate a valve by external power source for example, pneumatic air, hydraulics or electrical
drive motor
4 Design requirements
4.1 General
The requirements of the design shall be agreed. For this purpose, it is recommended to use the valve data
sheet (including for service conditions) in accordance with Annex A.
The valve shall be of either weir type (see Figure 1) or straight through type (see Figure 2) design.
Key
1 Handwheel
2 Stem with indicator
3 Bonnet
4 Compressor
5 Diaphragm
6 Body
Figure 1 — Weir type valve
Key
1 Handwheel
2 Stem with indicator
3 Bonnet
4 Compressor
5 Diaphragm
6 Body
Figure 2 — Straight through type valve
The design details are not specified in this document.
NOTE The choice of design and material depends on the design working temperature and the physical and
chemical characteristics of the fluid.
This document covers the dimensioning procedures of the shell, using materials other than those
specified in EN 12516-1:2014+A1:2018, EN 12516-2:2014+A1:2021, EN 12516-3:2002 or EN 12516-
4:2014+A1:2018. This document does not cover the dimensioning of parts other than the shell.
The design of the parts other than the shell is determined for a differential pressure defined by the
pressure/temperature rating or for a differential pressure which shall be indicated on the valve.
In the framework of the environmental urgency and sustainability requirements, the diaphragm valve
shall be designed to be easily repairable, durable and recyclable. Spare parts shall be made available.
The sound engineering practices are applicable (for example, number of screw threads engaged, two
screw threads overrun, …).
4.2 Shell
4.2.1 The shell is the combination of valve components comprising the pressure containing envelope,
such as:
— the body and the bonnet bolting if any,
— if used in end of line service, the obturator (diaphragm).
4.2.2 The shell strength shall be determined by one or more of the following standards:
a) according to EN 16668:2025, 5.1.2.1 or EN 16668:2025, 5.1.2.2 for shell components made of steel;
b) according to EN 12516-4:2014+A1:2018, 5.5.1, for copper alloy, aluminium and cast iron valves, for
the permissible membrane stress.
4.2.3 For applications out of the scope of the European legislation for pressure equipment, the
following standards shall apply:
a) for steel valves designed by the tabulation method: according to EN 12516-1:2014+A1:2018;
b) for steel valves designed by calculation solely: according to EN 12516-2:2014+A1:2021;
c) for copper alloy, aluminium and cast iron valves: according to EN 12516-4:2014+A1:2018;
d) by experimental method: according to EN 12516-3:2002.
Alternative standards based on sound engineering practice can be used.
4.2.4 If the foreseeable conditions lead to the assumption that the allowable limits will be exceeded,
then the design shall take this into account.
NOTE 1 See Annex D showing the relationship between this document and EN 16668:2025 requirements
concerning dimensioning.
NOTE 2 Other dimensioning methods (i.e. finite elements) are not specified in this document.
4.3 Body
4.3.1 General
Bodies shall be:
— straight, angle or oblique pattern;
— lined with elastomeric or plastic lining or unlined.
Elastomeric or plastic linings can be extended over the flange faces of the body to form a gasket for the
flange.
Any limitation regarding end of line service condition shall be indicated.
4.3.2 End connections
End connections shall be either one of the following.
a) Double flanged diaphragm valve: diaphragm valve having double flanged body ends for connection
to flanges of adjacent components by individual bolting.
Flanges shall have bolt holes in accordance with the relevant standard as specified in 4.10.2.
b) Butt welding end diaphragm valve: diaphragm valve intended for butt welding into a pipeline.
c) Mechanical connection: diaphragm valve with one or two interfaces for connection of piping. The
connection shall be spigot end or socket end. Requirements and test methods of mechanical joints
are described in EN 545:2010. The connection can be pullout proof.
d) Threaded ends diaphragm valve: diaphragm valve intended to be threaded into the pipeline.
e) Hygienic clamp connection: diaphragm valve with hygienic clamp connection.
4.4 Obturator (diaphragm)
The obturator (often named diaphragm) shall be replaceable.
Unique identifier or lot traceability should be marked on the diaphragm.
Material type or grade should be marked on the diaphragm and readable in the as installed condition.
4.5 Bonnet
Bonnets shall be stem sealed or non-stem sealed. Valves with stem sealed bonnets shall have a seal
between the stem and the bonnet neck to contain the line pressure or vacuum without leakage and can
be designed such that a means of checking diaphragm failure could be supplied.
In the case of a steam sealed bonnet, if pressurized, it shall form part so the valve shell. Therefore, wall
thickness of the bonnet shall be designed in accordance with this requirement.
4.6 Stem, compressor and other working parts
The stem, compressor and other working parts shall be isolated from the line fluid by means of the
diaphragm.
4.7 Optional design features
a) Indication: Valves can be fitted with a visible means of indicating the open and shut positions;
b) Fire type tested design: valves designated as fire type tested design shall be tested in accordance with
EN ISO 10497:2022;
If valves are required to be a fire type tested design, this requirement shall be specified
(see Annex A);
c) Anti-static design: valves with anti-static design shall have electrical continuity between shaft,
obturator and body in accordance with EN 12266-2:2012;
If valves are required to be an anti-static design, this requirement shall be specified (see Annex A);
d) Valves can be designed with stroke limiting devices to prevent full opening or closing of the obturator
dependent on application requirements.
4.8 Materials
4.8.1 Shell materials
4.8.1.1 For applications in the scope of the European legislation for pressure equipment, materials
for the shell components shall be selected according to EN 16668:2025, 5.2.
The inspection documents of material shall be in accordance with EN 764-5:2014.
NOTE See Annex D for the requirements of EN 16668:2025 for the shell materials for valves subject to the
European legislation for pressure equipment.
4.8.1.2 For applications out of the scope of the European legislation for pressure equipment,
materials for the shell components shall be selected from those described in EN 12516-1:2014+A1:2018,
for steel valves, or EN 12516-4:2014+A1:2018, for copper alloy, aluminium and cast iron valves.
4.8.1.3 Other materials for the shell components can be used providing that they are appropriate to
the intended use of a metallic diaphragm valve.
4.8.2 Body and bonnet bolting material
Material selection for body and bonnet bolting shall be in accordance with EN 10269:2013.
Other bolting materials may be used providing that they are appropriate to the intended us
...