SIST EN 300 698 V2.3.1:2019
(Main)Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services
Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services
The present document specifies technical characteristics and methods of measurements for VHF radio transmitters and
receivers operating on board ships in frequency bands allocated to the maritime mobile service, used on inland
waterways as defined by Regional Agreements or responsible Administrations.
The present document applies to VHF transmitters and receivers fitted with a 50 Ω external antenna socket or connector
for use on board ships on inland waterways and operating in the bands between 156 MHz and 174 MHz allocated to the
maritime mobile service by the ITU Radio Regulations [1], Appendix 18.
For countries where the Automatic Transmitter Identification System (ATIS) is mandatory, the requirements of annex B
apply as well.
NOTE: The relationship between the present document and essential requirements of article 3.2 and article 3.3(g)
of Directive 2014/53/EU [i.3] is given in annex A.
Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani standard za dostop do radijskega spektra in za funkcije storitev v sili
Ta dokument določa tehnične lastnosti in metode merjenja za radijske oddajnike in sprejemnike VHF na ladjah, ki uporabljajo frekvenčne pasove, dodeljene za pomorske mobilne storitve, in se uporabljajo na celinskih vodnih poteh, kot določajo regionalni sporazumi ali pristojni upravni organi.
Ta dokument se uporablja za oddajnike in sprejemnike VHF, ki so opremljeni z zunanjo 50-ohmsko antensko vtičnico ali priključkom za uporabo na ladjah na celinskih vodnih poteh ter delujejo v pasovih med 156 MHz in 174 MHz, dodeljenih za pomorske mobilne storitve v skladu s Pravilnikom o radiokomunikacijah Mednarodne telekomunikacijske zveze [1], dodatek 18.
Za države, v katerih je obvezna uporaba avtomatskega sistema za identifikacijo radijskih oddajnikov (ATIS), se uporabljajo tudi zahteve v dodatku B.
OPOMBA: Razmerje med tem dokumentom ter bistvenimi zahtevami člena 3.2 in člena 3.3(g) Direktive 2014/53/EU [i.3] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani standard za dostop do radijskega spektra in za funkcije storitev v siliRadio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 698 V2.3.1 (2018-11)SIST EN 300 698 V2.3.1:2019en01-januar-2019SIST EN 300 698 V2.3.1:2019SLOVENSKI
STANDARD
SIST EN 300 698 V2.3.1:2019
ETSI EN 300 698 V2.3.1 (2018-11) Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
HARMONISED EUROPEAN STANDARD SIST EN 300 698 V2.3.1:2019
ETSI ETSI EN 300 698 V2.3.1 (2018-11) 2
Reference REN/ERM-TG26-597 Keywords harmonised standard, maritime, radio, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the oneM2M Partners. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 300 698 V2.3.1:2019
ETSI ETSI EN 300 698 V2.3.1 (2018-11) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 9 3.3 Abbreviations . 9 4 General and operational requirements . 9 4.0 Conformance . 9 4.1 Construction . 10 4.2 Controls and indicators . 10 4.3 Handset and loudspeaker . 11 4.4 Switching time . 11 4.5 Safety precautions . 11 4.6 Class of emission and modulation characteristics . 12 4.7 Labelling. 12 4.8 Warm up . 12 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Test power source . 12 5.3 Normal test conditions . 12 5.3.1 Normal temperature and humidity . 12 5.3.2 Normal power sources . 13 5.3.2.1 Mains voltage and frequency . 13 5.3.2.2 Battery power source. 13 5.3.2.3 Other power sources . 13 5.4 Extreme test conditions . 13 5.4.1 Extreme temperatures . 13 5.4.2 Extreme values of test power sources . 13 5.4.2.1 Mains voltage . 13 5.4.2.2 Battery power source. 13 5.4.2.3 Other power sources . 13 5.5 Procedure for tests at extreme temperatures . 13 6 General conditions of measurement . 14 6.1 Arrangements for test signals applied to the receiver . 14 6.2 Squelch . 14 6.3 Normal test modulation . 14 6.4 Artificial antenna . 14 6.5 Arrangements for test signals applied to the transmitter . 14 6.6 Tests on equipment with a duplex filter . 14 6.7 Test channels . 14 6.8 Transmission time limitation . 14 6.9 Reference Bandwidths for emission measurements . 15 7 Environmental tests . 15 7.1 Introduction . 15 7.2 Procedure . 15 7.3 Performance check . 15 7.4 Vibration. 16 SIST EN 300 698 V2.3.1:2019
ETSI ETSI EN 300 698 V2.3.1 (2018-11) 4 7.5 Damp heat cycle . 16 8 Transmitter . 16 8.0 General . 16 8.1 Frequency error . 17 8.1.1 Definition . 17 8.1.2 Method of measurement . 17 8.1.3 Limits . 17 8.2 Carrier power . 17 8.2.1 Definitions . 17 8.2.2 Method of measurement . 17 8.2.3 Limits . 17 8.2.3.1 Normal test conditions . 17 8.2.3.2 Extreme test conditions . 17 8.3 Frequency deviation . 18 8.3.1 Definition . 18 8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18 8.3.2.1 Method of measurement . 18 8.3.2.2 Limits . 18 8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18 8.3.3.1 Method of measurement . 18 8.3.3.2 Limits . 18 8.4 Limitation characteristics of the modulator . 19 8.4.1 Definition . 19 8.4.2 Method of measurement . 19 8.4.3 Limits . 19 8.5 Sensitivity of the modulator, including microphone . 19 8.5.1 Definition . 19 8.5.2 Method of measurement . 19 8.5.3 Limits . 20 8.6 Audio frequency response . 20 8.6.1 Definition . 20 8.6.2 Method of measurement . 20 8.6.3 Limit . 20 8.7 Audio frequency harmonic distortion of the emission. 21 8.7.1 Definition . 21 8.7.2 Method of measurement . 21 8.7.2.1 General . 21 8.7.2.2 Normal test conditions . 22 8.7.2.3 Extreme test conditions . 22 8.7.3 Limit . 22 8.8 Adjacent channel power . 22 8.8.1 Definition . 22 8.8.2 Method of measurement . 22 8.8.3 Limits . 22 8.9 Conducted spurious emissions conveyed to the antenna . 23 8.9.1 Definition . 23 8.9.2 Method of measurement . 23 8.9.3 Limit . 23 8.10 Residual modulation of the transmitter . 23 8.10.1 Definition . 23 8.10.2 Method of measurement . 23 8.10.3 Limit . 23 8.11 Transient frequency behaviour of the transmitter . 23 8.11.1 Definitions . 23 8.11.2 Method of measurement . 24 8.11.3 Limits . 25 8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27 8.12.1 Definitions . 27 8.12.2 Method of measurement . 27 8.12.3 Limits . 28 SIST EN 300 698 V2.3.1:2019
ETSI ETSI EN 300 698 V2.3.1 (2018-11) 5 9 Receiver . 28 9.1 Harmonic distortion and rated audio frequency output power . 28 9.1.1 Definition . 28 9.1.2 Method of measurement . 28 9.1.3 Limits . 29 9.2 Audio frequency response . 29 9.2.1 Definition . 29 9.2.2 Method of measurement . 29 9.2.3 Limits . 29 9.3 Maximum usable sensitivity . 30 9.3.1 Definition . 30 9.3.2 Method of measurement . 31 9.3.3 Limits . 31 9.4 Co-channel rejection. 31 9.4.1 Definition . 31 9.4.2 Method of measurement . 31 9.4.3 Limit . 31 9.5 Adjacent channel selectivity . 31 9.5.1 Definition . 31 9.5.2 Method of measurement . 32 9.5.3 Limits . 32 9.6 Spurious response rejection . 32 9.6.1 Definition . 32 9.6.2 Method of measurement . 32 9.6.3 Limit . 32 9.7 Intermodulation response . 33 9.7.1 Definition . 33 9.7.2 Method of measurement . 33 9.7.3 Limit . 33 9.8 Blocking or desensitization . 33 9.8.1 Definition . 33 9.8.2 Method of measurement . 33 9.8.3 Limit . 34 9.9 Conducted spurious emissions conveyed to the antenna . 34 9.9.1 Definition . 34 9.9.2 Method of measurement . 34 9.9.3 Limit . 34 9.10 Amplitude response of the receiver limiter . 34 9.10.1 Definition . 34 9.10.2 Method of measurement . 34 9.10.3 Limit . 34 9.11 Receiver noise and hum level . 34 9.11.1 Definition . 34 9.11.2 Method of measurement . 35 9.11.3 Limit . 35 9.12 Squelch operation . 35 9.12.1 Definition . 35 9.12.2 Method of measurement . 35 9.12.3 Limits . 35 9.13 Squelch hysteresis . 36 9.13.1 Definition . 36 9
...
ETSI EN 300 698 V2.3.1 (2018-11)
HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum
and for features for emergency services
---------------------- Page: 1 ----------------------
2 ETSI EN 300 698 V2.3.1 (2018-11)
Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 698 V2.3.1 (2018-11)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 13
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 14
6.7 Test channels . 14
6.8 Transmission time limitation . 14
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 15
7.4 Vibration. 16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 698 V2.3.1 (2018-11)
7.5 Damp heat cycle . 16
8 Transmitter . 16
8.0 General . 16
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 17
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 19
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 698 V2.3.1 (2018-11)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 29
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement . 35
9.12.3 Limits . 35
9.13 Squelch hysteresis . 36
9.13.1 Definition . 36
9.13.2 Method of measurement . 36
9.13.3 Limit . 36
9.14 Radiated spurious emissions. 36
9.14.1 Definition .
...
Draft ETSI EN 300 698 V2.3.0 (2018-08)
HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum and for
features for emergency services
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 15
6.7 Test channels . 15
6.8 Transmission time limitation . 15
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 16
7.4 Vibration. 16
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 698 V2.3.0 (2018-08)
7.5 Damp heat cycle . 16
8 Transmitter . 17
8.0 General . 17
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 18
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 20
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 698 V2.3.0 (2018-08)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 30
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement . 35
9.12.3 Limits . 35
9.13 Squelch hysteresis . 36
9.13.1 Definition . 36
9.13.2 Method of measurement . 36
9.13.3 Limit . 36
9.14 Radiated spurious emissions. 36
9.14.1 Definition .
...
SLOVENSKI STANDARD
oSIST prEN 300 698 V2.3.0:2018
01-oktober-2018
Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo
v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani
standard za dostop do radijskega spektra in za funkcije storitev v sili
Radio telephone transmitters and receivers for the maritime mobile service operating in
the VHF bands used on inland waterways - Harmonised Standard for access to radio
spectrum and for features for emergency services
Ta slovenski standard je istoveten z: ETSI EN 300 698 V2.3.0 (2018-08)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
oSIST prEN 300 698 V2.3.0:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 698 V2.3.0:2018
---------------------- Page: 2 ----------------------
oSIST prEN 300 698 V2.3.0:2018
Draft ETSI EN 300 698 V2.3.0 (2018-08)
HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum and for
features for emergency services
---------------------- Page: 3 ----------------------
oSIST prEN 300 698 V2.3.0:2018
2 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 698 V2.3.0:2018
3 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 15
6.7 Test channels . 15
6.8 Transmission time limitation . 15
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 16
7.4 Vibration. 16
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 698 V2.3.0:2018
4 Draft ETSI EN 300 698 V2.3.0 (2018-08)
7.5 Damp heat cycle . 16
8 Transmitter . 17
8.0 General . 17
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 18
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 20
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 698 V2.3.0:2018
5 Draft ETSI EN 300 698 V2.3.0 (2018-08)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 30
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.