Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-21: Examinations and measurements - Switching time (IEC 61300-3-21:2019)

The document describes a method to measure the switching time and related performance parameters of a fibre optic spatial switch when the actuation energy is applied or removed to change the state of the switch.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3-21: Untersuchungen und Messungen - Schaltzeit (IEC 61300-3-21:2019)

Dispositifs d’interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures - Partie 3-21: Examens et mesures - Temps de commutation (IEC 61300-3-21:2019)

IEC 61300-3-21:2019 est disponible sous forme de IEC 61300-3-21:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

IEC 61300-3-21:2019 décrit une méthode en vue de mesurer le temps de commutation et les paramètres de performances associés d'un commutateur spatial fibronique, lorsque l'énergie d'activation est appliquée ou retirée pour modifier l'état du commutateur. Cette troisième édition annule et remplace la deuxième édition parue en 2014 dont elle constitue une révision technique. La présente édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- modifications pour éviter les redondances avec l'IEC 60876-1;
- clarifications des définitions et des schémas;
- généralisation des appareils de détection autres que les oscilloscopes.
Mots-clés : temps de commutation, paramètres de performances associés d'un commutateur spatial fibronique, énergie d'activation

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 3-21. del: Preiskave in meritve - Preklopni čas (IEC 61300-3-21:2019)

Ta dokument opisuje metodo za merjenje preklopnega časa in povezanih parametrov zmogljivosti optičnega prostorskega stikala ob vklopu ali izklopu napajanja za spremembo stanja stikala.

General Information

Status
Published
Public Enquiry End Date
28-Sep-2017
Publication Date
24-Nov-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
20-Nov-2019
Due Date
25-Jan-2020
Completion Date
25-Nov-2019

Relations

Buy Standard

Standard
EN IEC 61300-3-21:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61300-3-21:2020
01-januar-2020
Nadomešča:
SIST EN 61300-3-21:2016
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 3-21. del: Preiskave in meritve - Preklopni čas (IEC 61300-3-21:2019)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-21: Examinations and measurements - Switching time
(IEC 61300-3-21:2019)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 3-21: Untersuchungen und Messungen - Schaltzeit (IEC 61300-3-
21:2019)
Dispositifs d’interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 3-21: Examens et mesures - Temps de
commutation (IEC 61300-3-21:2019)
Ta slovenski standard je istoveten z: EN IEC 61300-3-21:2019
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61300-3-21:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61300-3-21:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 61300-3-21:2020


EUROPEAN STANDARD EN IEC 61300-3-21

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2019
ICS 33.180.20 Supersedes EN 61300-3-21:2015 and all of its
amendments and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 3-21:
Examinations and measurements - Switching time
(IEC 61300-3-21:2019)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procedures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3-
mesures - Partie 3-21: Examens et mesures - Temps de 21: Untersuchungen und Messungen - Schaltzeit
commutation (IEC 61300-3-21:2019)
(IEC 61300-3-21:2019)
This European Standard was approved by CENELEC on 2019-10-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61300-3-21:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61300-3-21:2020
EN IEC 61300-3-21:2019 (E)
European foreword
The text of document 86B/4218/FDIS, future edition 3 of IEC 61300-3-21, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-3-21:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2020-10-25
document have to be withdrawn
This document supersedes EN 61300-3-21:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61300-3-21:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60876-1:2014 NOTE Harmonized as EN 60876-1:2014 (not modified)


2

---------------------- Page: 4 ----------------------
SIST EN IEC 61300-3-21:2020
EN IEC 61300-3-21:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-3-4 -  Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures - Part 3-4:
Examinations and measurements -
Attenuation


3

---------------------- Page: 5 ----------------------
SIST EN IEC 61300-3-21:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 61300-3-21:2020



IEC 61300-3-21

®


Edition 3.0 2019-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 3-21: Examinations and measurements – Switching time




Dispositifs d’interconnexion et composants passifs fibroniques – Procedures

fondamentales d'essais et de mesures –


Partie 3-21: Examens et mesures – Temps de commutation













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.180.20 ISBN 978-2-8322-7376-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61300-3-21:2020
– 2 – IEC 61300-3-21:2019 © IEC 2019
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Apparatus . 6
4.1 General description . 6
4.2 Optical source (S) . 7
4.3 Detector (D) . 7
4.4 Actuation energy supply (AS) . 7
4.5 Data acquisition system (DAS) . 7
4.6 Termination (T) . 7
4.7 Temporary joint (TJ) . 7
5 Procedure . 8
6 Details to be specified . 9
Bibliography . 10

Figure 1 – Measurement set-up using a 2-channel DAS to measure a single output port . 8
Figure 2 – Example of a port moving to an on-state or off-state . 9

---------------------- Page: 8 ----------------------
SIST EN IEC 61300-3-21:2020
IEC 61300-3-21:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE
COMPONENTS – BASIC TEST AND MEASUREMENT PROCEDURES –

Part 3-21: Examinations and measurements – Switching time

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.