SIST EN ISO 2580-2:2004

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)

ISO 2580-2:2003 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of ABS moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize ABS moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 2580, as are the designatory properties in Part 1.

Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 2580-2:2003)

1.1   Dieser Teil von ISO 2580 legt die Verfahren zur Herstellung von Probekörpern und die zur Bestimmung der Eigenschaften von ABS-Form- und -Extrudiermassen anzuwendenden Prüfverfahren fest. Anforderungen an die Behandlung des Probenmaterials und für das Konditionieren des Probenmaterials vor der Herstellung der Probe-körper und der Probekörper vor der Prüfung sind ebenfalls enthalten.
1.2   Verfahren und Bedingungen für die Herstellung der Probekörper und Vorschriften für die Bestimmung der Eigenschaften der Formmassen, aus denen die Probekörper hergestellt werden, sind angegeben. Eigenschaften und Prüfverfahren, die anwendbar und notwendig sind, um ABS-Formmassen zu charakterisieren, sind aufgelistet.
1.3   Die Eigenschaften wurden aus den in ISO 10350 festgelegten, allgemeinen Prüfverfahren ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen, wie die kennzeichnenden Eigenschaften aus Teil 1 dieser Norm, sind in diesen Teil von ISO 2580 aufgenommen.
1.4   Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, ist es notwendig, dass die hier festge-legten Bedingungen der Probekörperherstellung und -konditionierung, die Probekörper mit den hier festge-legten Abmessungen sowie die hier festgelegten Prüfverfahren angewendet werden. Die gemessenen Werte müssen nicht notwendigerweise mit denen identisch sein, die bei der Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit anderen Verfahren hergestellt wurden, erhalten werden.

Plastiques - Acrylonitrile-butadiene-styrene (ABS) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 2580-2:2003)

L'ISO 2580-2:2003 spécifie les méthodes de préparation des éprouvettes de matériaux ABS pour moulage et extrusion, ainsi que les méthodes de mesurage de leurs propriétés. Sont également données les exigences relatives à la manipulation des matériaux d'essai et au conditionnement tant du matériau d'essai avant le moulage que des éprouvettes préalablement aux essais.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes et les modes opératoires pour le mesurage des propriétés des matériaux constituant ces éprouvettes sont précisés. La liste des propriétés et des méthodes d'essais appropriées et nécessaires pour caractériser les matériaux ABS pour moulage et extrusion est également donnée.
Les propriétés ont été sélectionnées parmi les méthodes générales d'essai traitées dans l'ISO 10350-1. D'autres méthodes couramment employées ou présentant un intérêt particulier pour ces matériaux pour moulage et extrusion sont également données dans l'ISO 2580-2:2003, de même que les propriétés de désignation spécifiées dans l'ISO 2580-1:2003.

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi terpolimerov akrilonitril- butadien-stirena (ABS) - 2. del: Priprava preskušancev in določanje lastnosti (ISO 2580-2:2003)

General Information

• Status: Withdrawn
• Publication Date: 31-Jan-2004
• Withdrawal Date: 04-Apr-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Apr-2019
• Due Date: 28-Apr-2019
• Completion Date: 05-Apr-2019
• Ref Project: EN ISO 2580-2:2003 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)

Relations

• Replaced By: SIST EN ISO 19062-2:2019 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)
• Effective Date: 03-Apr-2019
• Replaces: SIST EN ISO 2580-2:2000 - Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:1994)
• Effective Date: 01-Feb-2004
• Revised: SIST EN ISO 19062-2:2019 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)
• Effective Date: 30-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2580-2:2004
01-februar-2004
1DGRPHãþD
SIST EN ISO 2580-2:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYL
WHUSROLPHURYDNULORQLWULOEXWDGLHQVWLUHQD$%6GHO3ULSUDYDSUHVNXãDQFHYLQ
GRORþDQMHODVWQRVWL,62
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part
2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)
Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 2580-2:2003)
Plastiques - Acrylonitrile-butadiene-styrene (ABS) pour moulage et extrusion - Partie 2:
Préparation des éprouvettes et détermination des propriétés (ISO 2580-2:2003)
Ta slovenski standard je istoveten z: EN ISO 2580-2:2003
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2580-2:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2580-2:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 2580-2:2004
EUROPEAN STANDARD
EN ISO 2580-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 83.080.20 Supersedes EN ISO 2580-2:1999
English version
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and
extrusion materials - Part 2: Preparation of test specimens and
determination of properties (ISO 2580-2:2003)
Plastiques - Acrylonitrile-butadiène-styrène (ABS) pour Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen
moulage et extrusion - Partie 2: Préparation des - Teil 2: Herstellung von Probekörpern und Bestimmung
éprouvettes et détermination des propriétés (ISO 2580- von Eigenschaften (ISO 2580-2:2003)
2:2003)
This European Standard was approved by CEN on 10 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2580-2:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2580-2:2004
EN ISO 2580-2:2003 (E)
CORRECTED  2004-03-03
Foreword
This document (EN ISO 2580-2:2003) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2004, and conflicting national
standards shall be withdrawn at the latest by June 2004.
This document supersedes EN ISO 2580-2:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 2580-2:2003 has been approved by CEN as EN ISO 2580-2:2003 without any
modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 2580-2:2004
EN ISO 2580-2:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN/HD Year
ISO 62 1999 Plastics - Determination of water absorption EN ISO 62 1999
ISO 75-2 1993 Plastics - Determination of temperature of EN ISO 75-2 1996
deflection under load - Part 2: Plastics and
ebonite
ISO 293 1986 Plastics - Compression moulding test EN ISO 293 2003
specimens of thermoplastic materials
ISO 294-1 1996 Plastics - Injection moulding of test EN ISO 294-1 1998
specimens of thermoplastic materials - Part
1: General principles, and moulding of
multipurpose and bar test specimens
ISO 306 1994 Plastics - Thermoplastic materials - EN ISO 306 1996
Determination of Vicat softening temperature
(VST)
ISO 527-2 1993 Plastics - Determination of tensile properties EN ISO 527-2 1996
- Part 2: Test conditions for moulding and
extrusion plastics (including Corr 1:1994)
ISO 527-4 1997 Plastics - Determination of tensile properties EN ISO 527-4 1997
- Part 4: Test conditions for isotropic and
orthotopic fibre-reinforced plastic composites
ISO 1133 1997 Plastics - Determination of the melt mass- EN ISO 1133 1999
flow rate (MFR) and the melt volume-flow
rate (MVR) of thermoplastics
ISO 2818 1994 Plastics - Preparation of test specimens by EN ISO 2818 1996
machining
ISO 8256 1990 Plastics - Determination of tensile-impact EN ISO 8256 1996
strength (including Technical Corrigendum
1:1991)
3

---------------------- Page: 5 ----------------------

SIST EN ISO 2580-2:2004

---------------------- Page: 6 ----------------------

SIST EN ISO 2580-2:2004

INTERNATIONAL ISO
STANDARD 2580-2
Third edition
2003-12-01


Plastics — Acrylonitrile-butadiene-
styrene (ABS) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Acrylonitrile-butadiène-styrène (ABS) pour moulage et
extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés





Reference number
ISO 2580-2:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------

SIST EN ISO 2580-2:2004
ISO 2580-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2580-2:2004
ISO 2580-2:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Conformance . 1
3 Normative references . 1
4 Preparation of test specimens. 3
5 Conditioning of test specimens . 4
6 Determination of properties. 4
Annex A (normative) Determination of the bound-acrylonitrile content in the continuous phase. 7

© ISO 2003 — All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2580-2:2004
ISO 2580-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2580-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This third edition cancels and replaces the second edition (ISO 2580-2:1994), which has been technically
revised.
ISO 2580 consists of the following parts, under the general title Plastics — Acrylonitrile-butadiene-styrene
(ABS) moulding and extrusion materials:
 Part 1: Designation system and basis for specifications
 Part 2: Preparation of test specimens and determination of properties

iv © ISO 2003 — All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 2580-2:2004
INTERNATIONAL STANDARD ISO 2580-2:2003(E)

Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of properties
1 Scope
1.1 This part of ISO 2580 specifies the methods of preparation of test specimens and the test methods to
be used in determining the properties of ABS moulding and extrusion materials. Requirements for handling
test material and for conditioning both the test material before moulding and the specimens before testing are
given here.
1.2 Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test methods
which are suitable and necessary to characterize ABS moulding and extrusion materials are listed.
1.3 The properties have been selected from the general test methods in ISO 10350. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included in this
part of ISO 2580, as are the designatory properties specified in Part 1.
1.4 In order to obtain reproducible and comparable test results, it is necessary to use the methods of
specimen preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values d
...