SIST EN ISO 19062-2:2019

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)

This document specifies the methods of preparation of test specimens and the test methods to be
used in determining the properties of acrylonitrile-butadiene-styrene (ABS) moulding and extrusion
materials. Requirements for handling the test material and for conditioning both the test material
before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test methods
which are suitable and necessary to characterize ABS moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this document, as are the designatory properties specified in ISO 19062-1.
In order to obtain reproducible and comparable test results, it is intended to use the methods of
specimen preparation and conditioning, the specimen dimensions and the test procedures specified in
this document. Values determined will not necessarily be identical to those obtained using specimens
of different dimensions or prepared using different procedures.

Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 19062-2:2019)

Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die anzuwendenden Prüf-verfahren zur Bestimmung der Eigenschaften von Acrylnitril-Butadien-Styrol (ABS)-Formmassen fest. Anforderungen an die Behandlung des Probenmaterials und für die Konditionierung des Probenmaterials vor der Herstellung der Probekörper und der Probekörper vor der Prüfung sind ebenfalls enthalten.
Verfahren und Bedingungen für die Herstellung der Probekörper und Verfahren für die Bestimmung der Eigen¬schaften der Werkstoffe, aus denen die Probekörper hergestellt werden, sind angegeben. Eigen-schaften und Prüfverfahren, die anwendbar und notwendig sind, um ABS-Formmassen zu charakterisieren, sind aufgelistet.
Die Eigenschaften wurden aus den in ISO 10350 1 festgelegten, allgemeinen Prüfverfahren ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen, wie die kennzeichnenden Eigenschaften nach ISO 19062 1, sind in dieses Dokument aufgenommen.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, ist es vorgesehen, dass die in diesem Dokument festgelegten Verfahren der Probekörperherstellung und  konditionierung, die Probekörper-maße sowie die Prüfverfahren angewendet werden. Die gemessenen Werte werden nicht zwingend mit denen identisch sein, die bei der Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit anderen Verfahren hergestellt wurden, erhalten werden.

Plastiques - Matériaux à base d'acrylonitrile-butadiène-styrène (ABS) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 19062-2:2019)

Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai qui doivent être utilisées pour la détermination des propriétés des matériaux à base d'acrylonitrile-butadiène-styrène (ABS) pour moulage et extrusion. Les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai sont indiquées.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues sont donnés. Les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base d'ABS sont énumérées.
Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai largement utilisées ou qui revêtent une importance particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans le présent document; c'est le cas des propriétés de désignation spécifiées l'ISO 19062-1.
Dans le but d'obtenir des résultats d'essai reproductibles et comparables, il est nécessaire d'utiliser les méthodes de préparation et de conditionnement des éprouvettes, les dimensions d'éprouvette ainsi que les modes opératoires d'essai spécifiés dans le présent document. Les valeurs déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.

Polimerni materiali - Materiali na osnovi terpolimerov akrilonitril-butadien-stirena (ABS) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19062-2:2019)

Ta dokument določa metode za pripravo preskušancev in preskusnih metod za uporabo pri ugotavljanju lastnosti materialov na osnovi terpolimerov akrilonitril-butadien-stirena (ABS) za oblikovanje in ekstrudiranje. Podane so zahteve za ravnanje s preskusnim materialom ter obdelavo preskusnega materiala pred oblikovanjem in obdelavo preskušancev pred preskušanjem.
Podani so postopki in pogoji za pripravo preskušancev ter postopki za merjenje lastnosti materialov, iz katerih so izdelani preskušanci. Navedene so lastnosti in preskusne metode, ki so primerne ter nujne za opredelitev materialov na osnovi terpolimerov akrilonitril-butadien-stirena za oblikovanje in ekstrudiranje. Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki so v splošni uporabi ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta dokument. Vključene so tudi označevalne lastnosti, določene v standardu ISO 19062-1.
Da se zagotovijo primerljivi in ponovljivi rezultati preskusa, naj se uporabljajo metode priprave in obdelave primerka, mere preskušanca ter preskusni postopki, ki so določeni v tem dokumentu. Pri tem ni nujno, da bodo ugotovljene vrednosti enake tistim, ki so pridobljene z uporabo preskušancev, ki imajo drugačne mere ali so pripravljeni z uporabo drugih postopkov.

General Information

• Status: Published
• Public Enquiry End Date: 30-Apr-2018
• Publication Date: 15-Apr-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Apr-2019
• Due Date: 10-Jun-2019
• Completion Date: 16-Apr-2019
• Ref Project: EN ISO 19062-2:2019 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)

Relations

• Revised: SIST EN ISO 2580-2:2004 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)
• Effective Date: 30-Dec-2015
• Replaces: SIST EN ISO 2580-2:2004 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)
• Effective Date: 03-Apr-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19062-2:2019
01-junij-2019
1DGRPHãþD
SIST EN ISO 2580-2:2004
Polimerni materiali - Materiali na osnovi terpolimerov akrilonitril-butadien-stirena
(ABS) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in
ugotavljanje lastnosti (ISO 19062-2:2019)
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part
2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)
Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 19062-2:2019)
Plastiques - Matériaux à base d'acrylonitrile-butadiène-styrène (ABS) pour moulage et
extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
19062-2:2019)
Ta slovenski standard je istoveten z: EN ISO 19062-2:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19062-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 19062-2:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 19062-2:2019


EN ISO 19062-2
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2019
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 2580-2:2003
English Version

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding
and extrusion materials - Part 2: Preparation of test
specimens and determination of properties (ISO 19062-
2:2019)
Plastiques - Matériaux à base d'acrylonitrile- Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-
butadiène-styrène (ABS) pour moulage et extrusion - Formmassen - Teil 2: Herstellung von Probekörpern
Partie 2: Préparation des éprouvettes et détermination und Bestimmung von Eigenschaften (ISO 19062-
des propriétés (ISO 19062-2:2019) 2:2019)
This European Standard was approved by CEN on 8 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19062-2:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 19062-2:2019
EN ISO 19062-2:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 19062-2:2019
EN ISO 19062-2:2019 (E)
European foreword
This document (EN ISO 19062-2:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2580-2:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19062-2:2019 has been approved by CEN as EN ISO 19062-2:2019 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 19062-2:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 19062-2:2019
INTERNATIONAL ISO
STANDARD 19062-2
First edition
2019-03
Plastics — Acrylonitrile-butadiene-
styrene (ABS) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base d'acrylonitrile-butadiène-styrène
(ABS) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 19062-2:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------

SIST EN ISO 19062-2:2019
ISO 19062-2:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 19062-2:2019
ISO 19062-2:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of the material before moulding . 3
4.3 Injection moulding . 3
4.4 Compression moulding . 4
5 Conditioning of test specimens . 4
6 Determination of properties . 4
Annex A (normative) Determination of the bound-acrylonitrile content in the continuous phase .8
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 19062-2:2019
ISO 19062-2:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19062-2 cancels and replaces ISO 2580-2:2003, which has been technically
revised mainly to update the normative references in Clause 2:
— ISO 3167 has been replaced by ISO 20753;
— IEC 60093has been replaced by IEC 62631-3-1 and IEC 62631-3-2;
— ISO 1183 has been replaced by ISO 1183-1, ISO 1183-2 and ISO 1183-3.
A list of all parts in the ISO 19062 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 19062-2:2019
ISO 19062-2:2019(E)

Introduction
There are many methods for testing properties of plastics. For some, the data obtained by different
standards are not comparable. Even when the same standards have been used, they often allow the
adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this document is to specify methods and conditions of test to be used
for the acquisition and presentation of data to ensure that valid comparisons between acrylonitrile-
butadiene-styrene (ABS) materials can be made.
© ISO 2019 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 19062-2:2019

---------------------- Page: 12 ----------------------

SIST EN ISO 19062-2:2019
INTERNATIONAL STANDARD ISO 19062-2:2019(E)
Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be
used in determining the properties of acrylonitrile-butadiene-styrene (ABS) moulding and extrusion
materials. Requirements for handling the test material and for conditioning both the test material
before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test methods
which are suitable and necessary to characterize ABS moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this document, as are the designatory properties specified in ISO 19062-1.
In order to obtain reproducible and comparable test results, it is intended to use the methods of
specimen preparation and conditioning, the specimen dimensions and the test procedures specified in
this document. Values determined will not necessarily be identical to those obtained using specimens
of different dimensions or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 180, Plastics — Determination of Izod impact strength
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3:
Small plates
© ISO 2019 – All rights reserved
...