SIST EN 474-2:2007
(Main)Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers
Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to wheel and crawler tractor-dozers as defined in EN ISO 6165:2002, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This part also deals with rear-mounted winches for use on tractor-dozers.
The requirements of this part are complementary to the common requirements formulated in part 1.
This part does not repeat the requirements from part 1, but adds or replaces the requirements for application for tractor-dozers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of tractor-dozers.
This European Standard is not applicable to tractor-dozers manufactured before the date of publication of this European Standard by CEN.
Erdbaumaschinen - Sicherheit - Teil 2: Anforderungen für Planiermaschinen
Dieser Teil der EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Planiermaschinen wie in EN ISO 6165:2002 definiert zutreffen, wenn sie bestimmungsgemäß verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe Abschnitt 4).
Dieser Teil behandelt auch den Einsatz von Heckwinden auf Planiermaschinen.
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen des Teil 1.
Dieser Teil wiederholt nicht die Anforderungen des Teil 1, aber ergänzt oder ersetzt diese sofern sie für den Einsatz von Planiermaschinen von Bedeutung sind.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen die erforderlich sind, die Risiken die aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der Inbetriebnahme, dem Betrieb, der Instandhaltung von Planiermaschinen eintreten können zu mindern oder zu beseitigen.
Diese Europäische Norm ist nicht anzuwenden für Planiermaschinen, die vor der Veröffentlichung dieser Europäischen Norm durch CEN hergestellt wurden.
Engins de terrassement - Sécurité - Partie 2: Prescriptions applicables aux bouteurs
La présente partie de l’EN l’EN 474 traite de tous les phénomenes, situations et événements dangereux significatifs relatifs aux bouteurs a roues et a chenilles définis dans l'EN ISO 6165:2002 lorsqu'ils sont utilisés comme prévu ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir Aarticle 4).
La présente partie traite également des treuils montés a l’arriere de bouteurs.
Les exigences prescriptions figurant dans la présente partie sont viennent en complémentaires des exigences prescriptions communes présentées dans la partie 1.
La présente partie ne répete pas les exigences prescriptions de la partie 1 mais en ajoute ou en remplace certaines applicables aux bouteurs.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus aux phénomenes, situations et événements dangereux significatifs survenant lors de la mise en service, du fonctionnement et de la maintenance des bouteurs.
Le présent documentLa présente Norme européenne ne s'applique pas aux bouteurs fabriqués avant lsa publication de la présente Norme européenne par le CEN.
Stroji za zemeljska dela - Varnost - 2. del: Zahteve za buldožerje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozersStroji za zemeljska dela - Varnost - 2. del: Zahteve za buldožerjeEngins de terrassement - Sécurité - Partie 2: Prescriptions applicables aux bouteursErdbaumaschinen - Sicherheit - Teil 2: Anforderungen für PlaniermaschinenTa slovenski standard je istoveten z:EN 474-2:2006SIST EN 474-2:2007en53.100Stroji za zemeljska delaEarth-moving machineryICS:SIST EN 474-2:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 474-2:200701-maj-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 474-2November 2006ICS 53.100Supersedes EN 474-2:1996
English VersionEarth-moving machinery - Safety - Part 2: Requirements fortractor-dozersEngins de terrassement - Sécurité - Partie 2: Prescriptionsapplicables aux bouteursErdbaumaschinen - Sicherheit - Teil 2: Anforderungen fürPlaniermaschinenThis European Standard was approved by CEN on 17 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 474-2:2006: E
EN 474-2:2006 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 List of additional significant hazards.6 5 Safety requirements and/or measures.6 6 Information for use.7 Annex A (normative)
List of additional significant hazards – Tractor-dozers.8 Annex B (informative)
Illustrations.9 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.11 Bibliography.12
Figures Figure B.1 — Crawler tractor-dozer.9 Figure B.2 — Wheel tractor-dozer.9 Figure B.3 — Crawler tractor-dozer with a plough.10
Tables Table A.1 — List of additional significant hazards.8
EN 474-2:2006 (E) 3
Foreword This document (EN 474-2:2006) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2007, and conflicting national standards shall be withdrawn at the latest by November 2008. This European Standard supersedes EN 474-2:1996. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. For bibliographic references see EN 474-1:2006. EN 474 "Earth-moving machinery — Safety" comprises the following parts: Part 1: General requirements Part 2: Requirements for tractor-dozers Part 3: Requirements for loaders Part 4: Requirements for backhoe-loaders Part 5: Requirements for hydraulic excavators Part 6: Requirements for dumpers Part 7: Requirements for scrapers Part 8: Requirements for graders Part 9: Requirements for pipelayers Part 10: Requirements for trenchers Part 11: Requirements for earth and landfill compactors Part 12: Requirements for cable excavators This European Standard is intended for use in combination with Part 1 of the series. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 474-2:2006 (E) 4 Introduction This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard.
EN 474-2:2006 (E) 5 1 Scope This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to wheel and crawler tractor-dozers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This part also deals with rear-mounted winches for use on tractor-dozers. The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006. This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for tractor-dozers. This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.