SIST EN ISO 8033:2017
(Main)Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
This document specifies methods for the determination of the adhesion between lining and
reinforcement, between cover and reinforcement, between reinforcement layers, between cover and
outer lamination (thin layer of material outside the cover for protection) and between lining and inner
lamination (thin layer of material inside the lining to reduce permeation of fluid into the lining). It
covers all bore sizes and the following types of hose construction:
— woven textile fabric;
— braided textile fabric;
— knitted textile fabric;
— circular-woven textile fabric;
— textile spiral;
— textile cord;
— wire braid;
— wire spiral;
— hoses containing a supporting helix.
Adequate adhesion between the various components of a hose is essential if it is to perform satisfactorily
in service.
Gummi- und Kunststoffschläuche - Bestimmung der Haftung zwischen den einzelnen Schichten (ISO 8033:2016)
Diese Internationale Norm legt Verfahren für die Bestimmung der Haftfestigkeit zwischen Innenschicht und Einlagen, Außenschicht und Einlagen, zwischen den Einlagen, zwischen Außenschicht und äußerer Laminierung (dünne Materiallagen, die die Außenschicht schützen) und zwischen Innenschicht und innerer Laminierung (dünne Materiallagen innerhalb der Innenschicht, die die Durchlässigkeit von Flüssigkeit in die Innenschicht verringern) fest. Sie umfasst alle Nennweiten und die folgenden Schlauchkonstruktionen:
— Textilgewebe;
— Textilgeflecht;
— Textil, gestrickt;
— Textil, endlos gewebt;
— Textil, spiralgedreht;
— Textilcord;
— Drahtgeflecht;
— Drahtspirale;
— Schläuche mit Verstärkungsspirale.
Eine ausreichende Haftfestigkeit zwischen den verschiedenen Schichten eines Schlauchs ist ausschlaggebend für den zufriedenstellenden Einsatz im Betrieb.
Tuyaux en caoutchouc et en plastique - Détermination de l'adhérence entre éléments (ISO 8033:2016)
ISO 8033:2016 spécifie des méthodes pour la détermination de l'adhérence entre le tube intérieur et le renforcement, entre le revêtement et le renforcement, entre les couches de renforcement, entre le revêtement et la couche externe (fine couche de matériau à l'extérieur du revêtement, pour la protection) et entre le tube intérieur et la couche interne (fine couche de matériau à l'intérieur du tube, pour réduire la perméation du fluide dans le tube). Elle couvre tous les diamètres et les types suivants de confection de tuyaux:
- plis de tissu;
- fils textiles tressés;
- fils textiles tricotés;
- fils textiles tissés sur métier circulaire;
- fils textiles guipés
- nappes de fils textiles;
- fils métalliques tressés;
- fils métalliques guipés;
- tuyaux contenant une hélice support.
Une adhérence adéquate entre les différents éléments d'un tuyau est essentielle pour obtenir des performances satisfaisantes en service.
Gumene in polimerne cevi - Ugotavljanje adhezije med komponentami (ISO 8033:2016)
Ta dokument določa metode za ugotavljanje adhezije med oblogo in
ojačitvijo, med zaščitnim slojem in ojačitvijo, med plastmi ojačitve, med zaščitnim slojem in
zunanjo laminacijo (tanka plast materiala na zunanji strani zaščitnega sloja) ter med oblogo in notranjo
laminacijo (tanka plast materiala na notranji strani obloge za zmanjšanje prepustnosti tekočine v oblogo). Zajema
vse velikosti premerov in naslednje vrste cevnih sestavov:
– ploskovna tekstilija;
– tekstilni oplet;
– tekstilna tkanina;
– krožna ploskovna tekstilija;
– tekstilna spirala;
– tekstilna vrv;
– pramen;
– spiralna žica;
– cevi s podporno spiralo.
Ustrezna adhezija med različnimi komponentami cevi je bistvenega pomena za zadovoljivo
delovanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8033:2017
01-marec-2017
1DGRPHãþD
SIST EN ISO 8033:2006
Gumene in polimerne cevi - Ugotavljanje adhezije med komponentami (ISO
8033:2016)
Rubber and plastics hoses - Determination of adhesion between components (ISO
8033:2016)
Gummi- und Kunststoffschläuche - Bestimmung der Haftung zwischen den einzelnen
Schichten (ISO 8033:2016)
Tuyaux en caoutchouc et en plastique - Détermination de l'adhérence entre éléments
(ISO 8033:2016)
Ta slovenski standard je istoveten z: EN ISO 8033:2017
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 8033:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8033:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 8033:2017
EN ISO 8033
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2017
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 8033:2006
English Version
Rubber and plastics hoses - Determination of adhesion
between components (ISO 8033:2016)
Tuyaux en caoutchouc et en plastique - Détermination Gummi- und Kunststoffschläuche - Bestimmung der
de l'adhérence entre éléments (ISO 8033:2016) Haftung zwischen den einzelnen Schichten (ISO
8033:2016)
This European Standard was approved by CEN on 24 September 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8033:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8033:2017
EN ISO 8033:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8033:2017
EN ISO 8033:2017 (E)
European foreword
This document (EN ISO 8033:2017) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be
withdrawn at the latest by July 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 8033:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8033:2016 has been approved by CEN as EN ISO 8033:2017 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8033:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 8033:2017
INTERNATIONAL ISO
STANDARD 8033
Fourth edition
2016-12-15
Rubber and plastics hoses —
Determination of adhesion between
components
Tuyaux en caoutchouc et en plastique — Détermination de
l’adhérence entre éléments
Reference number
ISO 8033:2016(E)
©
ISO 2016
---------------------- Page: 7 ----------------------
SIST EN ISO 8033:2017
ISO 8033:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8033:2017
ISO 8033:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 General . 2
5.2 Test machine . 2
5.3 Grips . 2
5.4 Mandrel . 2
6 Test pieces . 2
6.1 Types of test piece . 2
6.1.1 General. 2
6.1.2 Type 1 . 2
6.1.3 Type 2 . 2
6.1.4 Type 3 . 3
6.1.5 Type 4 . 3
6.1.6 Type 5 . 3
6.1.7 Type 6 . 3
6.1.8 Type 7 . 3
6.1.9 Type 8 . 3
6.2 Test piece selection . 3
6.3 Test piece preparation . 4
6.3.1 General. 4
6.3.2 Type 1 . 4
6.3.3 Type 2 . 4
6.3.4 Type 3 . 4
6.3.5 Type 4 . 5
6.3.6 Type 5 . 5
6.3.7 Type 6 . 5
6.3.8 Type 7 . 5
6.3.9 Type 8 . 5
6.4 Conditioning of test pieces . 6
6.5 Time interval between vulcanization and testing . 6
7 Procedure. 6
7.1 Preparation . 6
7.2 Insertion of test pieces . 6
7.3 Test speed . 6
7.4 Measurement . 6
8 Expression of results . 6
9 Test report . 7
Bibliography .13
© ISO 2016 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8033:2017
ISO 8033:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This four
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.