kSIST FprEN 12167:2024
(Main)Copper and copper alloys - Profiles and bars for general purposes
Copper and copper alloys - Profiles and bars for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.
Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen Verwendung
Dieses Dokument legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Profile, einschließlich Profilen mit L-, T- und U-förmigen Quer
schnitten und Rechteckstangen aus Kupferlegierungen fest.
Dieses Dokument gilt für Profile mit L-, T- und U-förmigen Querschnitten mit einem Durchmesser des umschreibenden Kreises von höchstens 180mm und Rechteckstangen mit Dicken von 3mm bis 60mm und Breiten von 6mm bis 120mm.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforde
rungen dieses Dokuments sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Profilés et barres pour usages généraux
Le présent document spécifie la composition, les exigences de propriétés et les tolérances dimensionnelles des profilés en alliage de cuivre, incluant les sections en L, T, U et les barres, fabriqués par étirage ou filage.
Le présent document s’applique aux profilés à section en L, T et U s’inscrivant à l’intérieur d’un cercle d’un diamètre maximal de 180 mm, ainsi qu’aux barres d’épaisseur comprise entre 3 mm et 60 mm inclus et de largeur comprise entre 6 mm et 120 mm inclus.
Les modes opératoires d’échantillonnage et les méthodes d’essai pour la vérification de la conformité aux exigences du présent document sont également spécifiés.
Baker in bakrove zlitine - Profili in palice za splošno uporabo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 12167:2022
01-oktober-2022
Baker in bakrove zlitine - Profili in palice za splošno uporabo
Copper and copper alloys - Profiles and bars for general purposes
Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen
Verwendung
Cuivre et alliages de cuivre - Profilés et barres pour usages généraux
Ta slovenski standard je istoveten z: prEN 12167
ICS:
77.150.30 Bakreni izdelki Copper products
oSIST prEN 12167:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12167:2022
---------------------- Page: 2 ----------------------
oSIST prEN 12167:2022
DRAFT
EUROPEAN STANDARD
prEN 12167
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2022
ICS 77.150.30 Will supersede EN 12167:2016
English Version
Copper and copper alloys - Profiles and bars for general
purposes
Cuivre et alliages de cuivre - Profilés et barres pour Kupfer und Kupferlegierungen - Profile und
usages généraux Rechteckstangen zur allgemeinen Verwendung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 133.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12167:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12167:2022
prEN 12167:2022 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designations. 7
4.1 Material . 7
4.1.1 General . 7
4.1.2 Symbol . 7
4.1.3 Number . 7
4.2 Material condition . 7
4.3 Product . 8
5 O
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.