SIST EN 15311:2007
(Main)Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
This European Standard specifies technical supply conditions when using thermally sprayed coatings for manufacturing or repair of components.
Thermisches Spritzen - Bauteile mit thermisch gespritzten Schichten - Technische Lieferbedingungen
Diese Europäische Norm gilt für die Anwendung von thermisch gespritzten Schichten zur Fertigung oder
Instandsetzung von Bauteilen.
Projection thermique - Eléments traités par projection thermique - Conditions techniques de livraison
La présente Norme européenne prescrit les conditions techniques de livraison applicables lors de l’utilisation de la projection thermique dans le cadre de la fabrication ou de la réparation d’éléments.
Vroče brizganje – Sestavni deli s premazi, nanesenimi z vročim brizganjem – Tehnični dobavni pogoji
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Thermal spraying - Components with thermally sprayed coatings - Technical supply conditionsProjection thermique - Eléments traités par projection thermique - Conditions techniques de livraisonThermisches Spritzen - Bauteile mit thermisch gespritzten Schichten - Technische LieferbedingungenTa slovenski standard je istoveten z:EN 15311:2007SIST EN 15311:2007en;fr;de25.220.20Površinska obdelavaSurface treatmentICS:SLOVENSKI
STANDARDSIST EN 15311:200701-junij-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15311March 2007ICS 25.220.20 English VersionThermal spraying - Components with thermally sprayed coatings- Technical supply conditionsProjection thermique - Eléments traités par projectionthermique - Conditions techniques de livraisonThermisches Spritzen - Bauteile mit thermisch gespritztenSchichten - Technische LieferbedingungenThis European Standard was approved by CEN on 17 February 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15311:2007: E
EN 15311:2007 (E) 2 Contents
Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Requirements.4 5 Quality tests.6 Bibliography.9
EN 15311:2007 (E) 3 Foreword This document (EN 15311:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 15311:2007 (E) 4 1 Scope This European Standard specifies technical supply conditions when using thermally sprayed coatings for manufacturing or repair of components. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 473, Non destructive testing — Qualification and certification of NDT personnel — General principles EN 582,, Thermal spraying — Determination of tensile adhesive strength EN 657:2005, Thermal spraying — Terminology, classification EN 1395, Thermal spraying — Acceptance inspection of thermal spraying equipment EN 13214, Thermal spraying — Thermal spray coordination — Tasks and responsibilities EN ISO 2063, Thermal spraying — Metallic and other inorganic coatings — Zinc, aluminium and their alloys (ISO 2063:2005) EN ISO 4288, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture (ISO 4288:1996) EN ISO 8503-1, Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:1988) EN ISO 14918, Thermal spraying — Approval testing of thermal sprayers (ISO 14918:1998) EN ISO 14923, Thermal spraying — Characterization and testing of thermally sprayed coatings (ISO 14923:2003) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 apply. 4 Requirements 4.1 General requirements 4.1.1 Indication This European Standard specifying the general requirements for supply conditions should be indicated in the parts list or in delivery instructions. 4.1.2 Qualification of the manufacturer The manufacturer of the thermally sprayed coating for a component shall fulfil all requirements stipulated in the coating specification, should possess a quality management system, shall employ qualified personnel and is responsible to keep the spraying equipment in proper condition. The following standards shall be used to fulfil the requirements according to the quality requirements of the coated component:
EN 15311:2007 (E) 5 1) spraying co-ordinator (supervisor): qualified according to EN 13214 or qualified by appropriate knowledge in case of subordinate applications; 2) thermal sprayer (manual manufacturing): qualified according to EN ISO 14918 or qualified by appropriate knowledge; 3) thermal sprayer as an operator: apprenticed qualified on theoretical knowledge according to EN ISO 14918 or adequate experience; 4) non destructive testing – personnel qualification, if applicable: according to EN 473 class 2 for penetrant test (PT); 5) spraying equipment: checked according to the relevant part of EN 1395 or qualified by a correct function of the spraying equipment by test reports or coating results. 4.1.3 Preparing the instructions for thermal spraying (spray procedure specification) The manufacturer is responsible for preparing and ensuring the execution of instructions (see also EN ISO 14922). The spray procedure specification has to refer to the coating specification and the manufacturing instruction documents, like parts list, material instructions of parent metal and spraying material, drawings and test instructions. The spray procedure specification should be prepared in written form; only in case of subordinate applications will a verbal form be accepted. If required, the spray procedure specification may be qualified by a component related spray procedure qualification. 4.2 Technical requirements 4.2.1 Spraying materials Only spraying materials which are indicated in the spray procedure specification shall be applied. Preferably, the spraying material should comply with the technical supply conditions of EN 1274 for spraying powders and EN ISO 14919 for spraying wires, rods and cords. The conformity of the spraying material with the instructions in the spray procedure specification should be verified by comparison with the relevant test certificate from the manufacturer/supplier of the spraying material. The manufacturer/supplier processing instructions
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.