SIST EN 60587:2008
(Main)Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
This International standard describes two test methods for the evaluation of electrical insulating materials for use under severe ambient conditions at power frequencies (45 Hz to 65 Hz) by measurement of the resistance to tracking and erosion, using a liquid contaminant and inclined plane specimens. The two methods are as follows: - Method 1: constant tracking voltage; - Method 2: stepwise tracking voltage.
Elektroisolierstoffe, die unter erschwerten Bedingungen eingesetzt werden - Prüfverfahren zur Bestimmung der Beständigkeit gegen Kriechwegbildung und Erosion
Matériaux isolants électriques utilisés dans des conditions ambiantes sévères - Méthodes d'essai pour évaluer la résistance au cheminement et à l'érosion
La CEI 60587:2007 décrit deux méthodes d'essai pour évaluer les matériaux isolants électriques utilisés dans des conditions ambiantes sévères à des fréquences industrielles (comprises entre 45 Hz et 65 Hz), impliquant la mesure de la résistance au cheminement et à l'érosion, à l'aide d'un contaminant liquide et d'éprouvettes plates inclinées. Les deux méthodes sont les suivantes:
- Méthode 1: essai de résistance au cheminement à tension constante;
- Méthode 2: essai de résistance au cheminement par paliers de tension.
Les principales modifications suivantes ont été apportées par rapport à l'édition précédente: l'expérience a montré le besoin d'améliorer la description de la méthode expérimentale. Ensuite, en ce qui concerne la préparation des éprouvettes, l'abrasion est recommandée uniquement si nécessaire. La ventilation de l'enceinte d'essai est également décrite en détail. Un support de montage est décrit pour les éprouvettes constituées de matériaux élastomères souples. Enfin, la profondeur d'érosion maximale doit être mentionnée dans la classification. La version française de cette norme n'a pas été soumise au vote.
Elektroizolacijski materiali, ki se uporabljajo v težkih okoljskih razmerah - Preskušalne metode za ocenjevanje odpornosti proti razenju in eroziji (IEC 60587:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60587:2008
01-januar-2008
Elektroizolacijski materiali, ki se uporabljajo v težkih okoljskih razmerah -
Preskušalne metode za ocenjevanje odpornosti proti razenju in eroziji (IEC
60587:2007)
Electrical insulating materials used under severe ambient conditions - Test methods for
evaluating resistance to tracking and erosion
Elektroisolierstoffe, die unter erschwerten Bedingungen eingesetzt werden -
Prüfverfahren zur Bestimmung der Beständigkeit gegen Kriechwegbildung und Erosion
Matériaux isolants électriques utilisés dans des conditions ambiantes sévères -
Méthodes d'essai pour évaluer la résistance au cheminement et à l'érosion
Ta slovenski standard je istoveten z: EN 60587:2007
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
SIST EN 60587:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60587:2008
---------------------- Page: 2 ----------------------
SIST EN 60587:2008
EUROPEAN STANDARD
EN 60587
NORME EUROPÉENNE
July 2007
EUROPÄISCHE NORM
ICS 17.220.99; 29.035.01
English version
Electrical insulating materials
used under severe ambient conditions -
Test methods for evaluating resistance to tracking and erosion
(IEC 60587:2007)
Matériaux isolants électriques utilisés Elektroisolierstoffe, die unter erschwerten
dans des conditions ambiantes sévères - Bedingungen eingesetzt werden -
Méthodes d'essai pour évaluer Prüfverfahren zur Bestimmung
la résistance au cheminement der Beständigkeit gegen
et à l'érosion Kriechwegbildung und Erosion
(CEI 60587:2007) (IEC 60587:2007)
This European Standard was approved by CENELEC on 2007-06-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60587:2007 E
---------------------- Page: 3 ----------------------
SIST EN 60587:2008
EN 60587:2007 - 2 -
Foreword
The text of document 112/56/FDIS, future edition 3 of IEC 60587, prepared by IEC TC 112, Evaluation
and qualification of electrical insulating materials and systems, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 60587 on 2007-06-01.
This European Standard supersedes HD 380 S2:1987.
The main changes from HD 380 S2:1987 are as follows:
– experience has indicated the need for improved description of the experimental method;
– for the preparation of the test specimens, abrasion is recommended only if necessary;
– the ventilation of the test chamber is described in detail;
– for specimens of soft elastomeric materials a mounting support is described;
– the maximum depth of erosion has to be reported in the classification.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-03-01
– latest date by which the national standards conflicting
(dow) 2010-06-01
with the EN have to be withdrawn
__________
Endorsement notice
The text of the International Standard IEC 60587:2007 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 60587:2008
INTERNATIONAL IEC
STANDARD 60587
Third edition
2007-05
Electrical insulating materials
used under severe ambient conditions –
Test methods for evaluating resistance
to tracking and erosion
PRICE CODE
Commission Electrotechnique Internationale
P
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
---------------------- Page: 5 ----------------------
SIST EN 60587:2008
– 2 – 60587 © IEC:2007(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Terms and definitions .5
3 Test specimens .6
3.1 Dimensions .6
3.2 Preparation .6
4 Apparatus.6
4.1 Electrical apparatus.6
4.2 Electrodes .8
4.3 Contaminant.9
4.4 Timing device .10
4.5 Depth gauge.10
4.6 Ventilation .10
5 Procedure .11
5.1 Preparation of the test.11
5.2 Method 1: Application of constant tracking voltage .13
5.3 Method 2: stepwise tracking voltage.14
5.4 End-point criteria.14
6 Test report.15
Table 1 – Test parameters .8
Figure 1 – Test specimen with holes for fixing electrodes .6
Figure 2 – Schematic circuit diagram .7
Figure 3 – Example: typical circuit for an overcurrent delay relay (F in Figure 2).8
Figure 4 – Top electrode, stainless steel 0,5 mm thick .9
Figure 5 – Bottom electrode, stainless steel 0,5 mm thick .9
Figure 6 – Assembly of the electrodes .10
Figure 7 – Test assembly, schematic .11
Figure 8 – Mounting support .12
Figure 9 – Filter-paper (eight sheets requested for each top electrode).12
---------------------- Page: 6 ----------------------
SIST EN 60587:2008
60587 © IEC:2007(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________
ELECTRICAL INSULATING MATERIALS
USED UNDER SEVERE AMBIENT CONDITIONS −
TEST METHODS FOR EVALUATING RESISTANCE TO TRACKING
AND EROSION
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60587 has been prepared by IEC technical committee 112:
Evaluation and qualification of electrical insulating materials and systems.
This third edition cancels and replaces the second edition, published in 1984, and constitutes
a technical revision. The main changes from the previous edition are as follows: experience
has indicated the need for improved description of the experimental method. For the
preparation of the test specimens abrasion is recommended only if necessary. The ventilation
of the test chamber is described in detail. For specimens of soft elastomeric materials a
mounting support is described. The maximum depth of erosion has to be reported in the
classification.
---------------------- Page: 7 ----------------------
SIST EN 60587:2008
– 4 – 60587 © IEC:2007(E)
The text of this standard is based on the following documents:
FDIS Report on voting
112/56/FDIS 112/61A/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 8 ----------------------
SIST EN 60587:2008
60587 © IEC:2007(E) – 5 –
ELECTRICAL INSULATING MATERIALS
USED UNDER SEVERE AMBIENT CONDITIONS −
TEST METHODS FOR EVALUATING RESISTANCE TO TRACKING
AND EROSION
1 Scope
This International standard describes two test methods for the evaluation of electrical
insulating materials for use under severe ambient conditions at power frequencies (45 Hz to
65 Hz) by measurement of the resistance to tracking and erosion, using a liquid contaminant
and inclined plane specimens. The two methods are as follows:
– Method 1: constant tracking voltage;
– Method 2: stepwise tracking voltage.
NOTE 1 Method 1 is the most widely used method as there is less need for continual inspection.
NOTE 2 The test conditions are designed to accelerate the production of the effects, but do not reproduce all the
conditions encountered in service.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
track
partially conducting path created by localized deterioration on the surface of an insulating
material
2.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.