Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic oxidation coatings - Chart scale method (ISO 10215:2018)

This document specifies a visual method for determining the image clarity of anodic oxidation coatings
on aluminium and its alloys, using a chart scale and a lightness scale, which are defined. The method is
applicable only to flat surfaces that can reflect the image of the chart scale pattern.

Anodisieren von Aluminium und Aluminiumlegierungen - Visuelle Bestimmung der Abbildungsschärfe von anodisch erzeugten Oxidschichten - Messgittermethode (ISO 10215:2018)

Dieses Dokument legt ein visuelles Verfahren zur Bestimmung der Abbildungsschärfe von anodisch erzeugten Oxidschichten auf Aluminium und seinen Legierungen fest. Dabei werden ein Messgitter und eine Helligkeitsskala verwendet, die definiert sind. Die Prüfung ist nur auf einer ebenen Fläche anwendbar, die das Bild des Messgitters reflektieren kann.

Anodisation de l'aluminium et de ses alliages - Détermination de la netteté d'image sur couches anodiques - Méthode des échelles graduées (ISO 10215:2018)

ISO 10215:2018 spécifie une méthode visuelle pour la détermination de la netteté de l'image réfléchie par les couches anodiques déposées sur l'aluminium et ses alliages, utilisant une échelle graduée et une échelle de clarté. La méthode n'est applicable qu'aux surfaces planes susceptibles de refléter l'image d'une échelle graduée type.

Anodizacija aluminija in aluminijevih zlitin - Vizualno ugotavljanje ostrine slike v anodizirani plasti - Metoda tabelarične lestvice (ISO 10215:2018)

Ta dokument opisuje vizualno metodo za določanje jasnosti slike anodno oksidiranih plasti
na aluminiju in aluminijevih zlitinah s pomočjo grafične lestvice in lestvice svetlosti, ki sta določeni. Ta metoda se uporablja samo na ravnih površinah, ki lahko odsevajo sliko vzorca grafične lestvice.

General Information

Status
Published
Public Enquiry End Date
24-Sep-2017
Publication Date
15-Apr-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
03-Apr-2018
Due Date
08-Jun-2018
Completion Date
16-Apr-2018

RELATIONS

Buy Standard

Standard
SIST EN ISO 10215:2018
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 10215:2018
01-maj-2018
1DGRPHãþD
SIST EN ISO 10215:2011

$QRGL]DFLMDDOXPLQLMDLQDOXPLQLMHYLK]OLWLQ9L]XDOQRXJRWDYOMDQMHRVWULQHVOLNHY

DQRGL]LUDQLSODVWL0HWRGDWDEHODULþQHOHVWYLFH ,62

Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic

oxidation coatings - Chart scale method (ISO 10215:2018)
Anodisieren von Aluminium und Aluminiumlegierungen - Visuelle Bestimmung der
Abbildungsschärfe von anodisch erzeugten Oxidschichten - Messgittermethode (ISO
10215:2018)

Anodisation de l'aluminium et de ses alliages - Détermination de la netteté d'image sur

couches anodiques - Méthode des échelles graduées (ISO 10215:2018)
Ta slovenski standard je istoveten z: EN ISO 10215:2018
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 10215:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 10215:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 10215:2018
EN ISO 10215
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2018
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN ISO 10215:2010
English Version
Anodizing of aluminium and its alloys - Visual
determination of image clarity of anodic oxidation coatings
- Chart scale method (ISO 10215:2018)
Anodisation de l'aluminium et de ses alliages - Anodisieren von Aluminium und

Détermination de la netteté d'image sur couches Aluminiumlegierungen - Visuelle Bestimmung der

anodiques - Méthode des échelles graduées (ISO Abbildungsschärfe von anodisch erzeugten

10215:2018) Oxidschichten - Messgittermethode (ISO 10215:2018)
This European Standard was approved by CEN on 16 March 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10215:2018 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10215:2018
EN ISO 10215:2018 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 10215:2018
EN ISO 10215:2018 (E)
European foreword

This document (EN ISO 10215:2018) has been prepared by Technical Committee ISO/TC 79 "Light

metals and their alloys" in collaboration with Technical Committee CEN/TC 132 “Aluminium and

aluminium alloys”, the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by September 2018, and conflicting national standards

shall be withdrawn at the latest by September 2018.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 10215:2010.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 10215:2018 has been approved by CEN as EN ISO 10215:2018 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 10215:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 10215:2018
INTERNATIONAL ISO
STANDARD 10215
Third edition
2018-01
Anodizing of aluminium and its
alloys — Visual determination of
image clarity of anodic oxidation
coatings — Chart scale method
Anodisation de l'aluminium et de ses alliages — Détermination de
la netteté d'image sur couches anodiques — Méthode des échelles
graduées
Reference number
ISO 10215:2018(E)
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 10215:2018
ISO 10215:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10215:2018
ISO 10215:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

5 Apparatus ..................................................................................................................................................................................................................... 2

6 Test specimen .......................................................................................................................................................................................................... 5

6.1 Sampling ....................................................................................................................................................................................................... 5

6.2 Size .................................................................................................................................................................................................................... 5

6.3 Treatment before testing ................................................................................................................................................................ 5

7 Procedure..................................................................................................................................................................................................................... 5

7.1 General ........................................................................................................................................................................................................... 5

7.2 Determination of image clearness, C .................................................................................................................................. 5

7.3 Determination of image distortion, I .................................................................................................................................. 6

7.4 Determination of haze value, H ............................................................................................................................................. 6

8 Expression of results ........................................................................................................................................................................................ 6

9 Test report ................................................................................................................................................................................................................... 7

Bibliography ................................................................................................................................................................................................................................ 8

© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10215:2018
ISO 10215:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO’s adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/ iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 79, Light metals and their alloys,

Subcommittee SC 2, Organic and anodic oxidation coatings on aluminium.

This third edition cancels and replaces the second edition (ISO 10215:2010), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— the normative reference of ISO/TR 8125 has been deleted since it has been
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.