SIST EN ISO 14723:2004

Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001)

Erdöl- und Erdgasindustrie - Rohrleitungs-Transportsysteme - Unterwasser-Rohrleitungssysteme (ISO 14723:2001)

Diese Internationale Norm legt Anforderungen fest und gibt Empfehlungen für die Konstruktion, Herstellung,        Prüfung und Dokumentation von Kugelventilen, Rückschlagventilen und Schiebern für Unterwasser-Anwendungen in Offshore-Rohrleitungssystemen, die den Anforderungen nach ISO 13623 für die Erdöl- und Erdgasindustrien entsprechen.
Diese Internationale Norm gilt nicht für Armaturen für Druckstufen über PN 420 (Klasse 2 500).
Anhang A der vorliegenden Internationalen Norm enthält Richtlinien, die den Abnehmer bei der Auswahl des         Armaturentyps und der Festlegung von Anforderungen zum Zeitpunkt der Bestellung von Armaturen unterstützen.
Anhang B der vorliegenden Internationalen Norm enthält eine Zusammenstellung der Angaben, die von dem Hersteller und/oder Abnehmer zum Zeitpunkt der Bestellung von Armaturen gemacht werden müssen.

Industries du pétrole et du gaz naturel - Systemes de transport par conduites - Vannes de conduites immergées (ISO 14723:2001)

Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2004
• Withdrawal Date: 22-Jun-2009
• ICS: 23.060.01 - Valves in general
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 23-Jun-2009
• Due Date: 16-Jul-2009
• Completion Date: 23-Jun-2009
• Ref Project: EN ISO 14723:2001 - Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001)

Relations

• Replaced By: SIST EN ISO 14723:2009 - Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)
• Effective Date: 01-Sep-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14723:2004
01-maj-2004
Petroleum and natural gas industries - Pipeline transportation systems - Subsea
pipeline valves (ISO 14723:2001)
Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline
valves (ISO 14723:2001)
Erdöl- und Erdgasindustrie - Rohrleitungs-Transportsysteme - Unterwasser-
Rohrleitungssysteme (ISO 14723:2001)
Industries du pétrole et du gaz naturel - Systemes de transport par conduites - Vannes
de conduites immergées (ISO 14723:2001)
Ta slovenski standard je istoveten z: EN ISO 14723:2001
ICS:
23.060.01 Ventili na splošno Valves in general
75.200 2SUHPD]DVNODGLãþHQMH Petroleum products and
QDIWHQDIWQLKSURL]YRGRYLQ natural gas handling
]HPHOMVNHJDSOLQD equipment
SIST EN ISO 14723:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14723:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 14723:2004
EUROPEAN STANDARD
EN ISO 14723
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 75.200
English version
Petroleum and natural gas industries - Pipeline transportation
systems - Subsea pipeline valves (ISO 14723:2001)
Industries du pétrole et du gaz naturel - Systèmes de Erdöl- und Erdgasindustrie - Rohrleitungs-
transport par conduites - Vannes de conduites immergées Transportsysteme - Unterwasser-Rohrleitungssysteme
(ISO 14723:2001) (ISO 14723:2001)
This European Standard was approved by CEN on 1 December 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14723:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14723:2004
EN ISO 14723:2001 (E)
CORRECTED  2002-09-25
Foreword
This document (EN ISO 14723:2001) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2002, and conflicting national
standards shall be withdrawn at the latest by June 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of ISO 14723:2001 has been approved by CEN as EN ISO 14723:2001 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 14723:2004

INTERNATIONAL ISO
STANDARD 14723
First edition
2001-12-01


Petroleum and natural gas industries —
Pipeline transportation systems — Subsea
pipeline valves
Industries du pétrole et du gaz naturel — Systèmes de transport par
conduites — Vannes de conduites immergées




Reference number
ISO 14723:2001(E)
©
 ISO 2001

---------------------- Page: 5 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2001 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
Contents Page
Foreword.v
Introduction.vi
1 Scope .1
2 Normative references.1
3 Terms and definitions .3
4 Symbols and abbreviated terms .7
4.1 Symbols.7
4.2 Abbreviated terms .7
5 Valve types and configurations .8
5.1 Valve types .8
5.2 Valve configuration .9
6 Design.19
6.1 Design codes and calculations .19
6.2 Pressure and temperature ratings .20
6.3 Cavity relief .20
6.4 External pressure and loads .20
6.5 Sizes.20
6.6 Face-to-face and end-to-end dimensions .21
6.7 Minimum bore full-opening valves .30
6.8 Valve operation .30
6.9 Pigging.30
6.10 Valve ends .31
6.11 Bypass, drain and vent connections.31
6.12 Handwheels and wrenches.31
6.13 Locking devices.32
6.14 Position indicators .32
6.15 ROV interface .32
6.16 Sealant injection .32
6.17 Lifting lugs .32
6.18 Actuators/gearbox .32
6.19 Drive trains .33
6.20 Stem shaft protector.34
6.21 Hydraulic lock .34
6.22 Corrosion/erosion.34
6.23 Hyperbaric performance .34
iii © ISO 2001 – All rights reserved

---------------------- Page: 7 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
6.24 Design document review .34
7 Material .34
7.1 Material specification .34
7.2 Service compatibility.35
7.3 Forged parts .35
7.4 Composition limits.35
7.5 Toughness test requirements .36
7.6 Bolting.37
7.7 Sour service .37
8 Welding .38
8.1 Qualifications .38
8.2 Impact testing.38
8.3 Hardness testing.38
9 Quality control.40
9.1 General.40
9.2 Measuring and test equipment.40
9.3 Qualification of inspection and test personnel .40
9.4 NDE .40
9.5 NDE of repair welding .41
10 Testing .41
10.1 General.41
10.2 Hydrostatic shell test .42
10.3 Operational/functional test .42
10.4 Hydrostatic seat test .43
10.5 Cavity relief test .45
10.6 Pneumatic seat test .45
11 Marking .45
12 Storing and shipping.49
12.1 Painting.49
12.2 Corrosion prevention .49
12.3 Protection .49
13 Documentation.49
Annex A (informative) Purchasing guidelines.51
Annex B (informative) Summary of information to be provided by manufacturer and/or purchaser .54
Annex C (normative) Supplementary test requirements.56
Annex D (normative) Supplementary documentation requirements .58
Annex E (normative) NDE requirements.59
Bibliography .62

iv © ISO 2001 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14723 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for
petroleum and natural gas industries, Subcommittee SC 2, Pipeline transportation systems.
Annexes C, D and E form a normative part of this International Standard. Annexes A and B are for information only.
© ISO 2001 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
Introduction
This International Standard is based on ISO 14313. It has been developed to address special requirements specific
to subsea pipeline valves.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a contractor from offering, or the
company from accepting, alternative engineering solutions for the individual application. This may be particularly
applicable where there is innovative or developing technology. Where an alternative is offered, the manufacturer
should identify any variations from this International Standard and provide details.

vi © ISO 2001 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 14723:2004
INTERNATIONAL STANDARD ISO 14723:2001(E)

Petroleum and natural gas industries — Pipeline transportation
systems — Subsea pipeline valves
1 Scope
This International Standard specifies requirements and gives recommendations for the design, manufacturing,
testing and documentation of ball, check and gate valves for subsea application in offshore pipeline systems
meeting the requirements of ISO 13623 for the petroleum and natural gas industries.
This International Standard is not applicable to valves for pressure ratings exceeding PN 420 (Class 2500).
Annex A of this International Standard provides guidelines to assist the purchaser with valve type selection and
specification of requirements when ordering valves.
Annex B of this International Standard provides a checklist summary of information to be provided by the
manufacturer and/or purchaser when ordering valves.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 7-1, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and
designation
ISO 148, Steel — Charpy impact test (V-notch)
ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances
and designation
ISO 228-2, Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means
of limit gauges
ISO 5208, Industrial valves — Pressure testing of valves
ISO 7005-1, Metallic flanges — Part 1: Steel flanges
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 10474, Steel and steel products — Inspection documents
ISO 13623, Petroleum and natural gas industries — Pipeline transportation systems
1)
ASME B1.1, Unified inch screw threads (UN and UNR thread form)

1) American Society of Mechanical Engineers, 345 East 47th Street, NY 10017-2392, USA.
© ISO 2001 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
ASME B1.20.1, Pipe threads, general purpose (inch)
ASME B16.5, Pipe flanges and flanged fittings — NPS 1/2 through NPS 24
ASME B16.10, Face-to-face and end-to-end dimensions of valves
ASME B16.25, Buttwelding ends
ASME B16.34, Valves — Flanged, threaded, and welding end
ASME B16.47, Large diameter steel flanges — NPS 26 through NPS 60
ASME B31.4, Pipeline transportation systems for liquid hydrocarbons and other liquids
ASME B31.8, Gas transmission and distribution systems
ASME Boiler and Pressure Vessel Code:1998, Section V, Non destructive examination
ASME Boiler and Pressure Vessel Code:1998, Section VIII, Division 1, Rules for construction of pressure vessels
ASME Boiler and Pressure Vessel Code, Section IX, Qualification standard for welding and brazing procedures,
welders, brazers, and welding and brazing operators
2)
ASTM A 320/A 320M, Standard specification for alloy steel bolting materials for low-temperature service
ASTM A 370, Standard test methods and definitions for mechanical testing of steel products
ASTM A 388/A 388M, Standard practice for ultrasonic examination of heavy steel forgings
ASTM A 435/A 435M, Standard specification for straight-beam ultrasonic examination of steel plates
ASTM A 577/A 577M, Standard specification for ultrasonic angle-beam examination of steel plates
ASTM A 578/A 578M, Standard specification for straight-beam ultrasonic examination of plain and clad steel plates
for special applications
ASTM A 609/A 609M:1997, Standard practice for castings, carbon low-alloy, and martensitic stainless steel,
ultrasonic examination thereof
3)
AWS QC1, Standard for AWS certification of welding inspectors
EN 287-1, Approval testing of welders — Fusion welding — Part 1: Steels
EN 288-3, Specification and approval of welding procedures for metallic materials  Part 3: Welding procedure
tests for the arc welding of steels
4)
MSS SP-44, Steel pipeline flanges
MSS SP-55, Quality standard for steel castings, flanges, fittings and other piping components — Visual method for
evaluation of surface irregularities
5)
NACE MR 0175, Sulfide stress cracking resistant metallic materials for oilfield equipment
NACE TM 0284, Evaluation of pipeline and pressure vessel steels for resistance to hydrogen-induced cracking

2) American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, USA.
3) The American Welding Society, 550 NW LeJeune Road, Miami, FL 33126, USA.
4) Manufacturers Standardization Society of the Valve & Fittings Industry Inc., 127 Park Street N.E., Vienna, VA 22180, USA.
5) National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218, USA.
2 © ISO 2001 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
ANSI rating class
numerical pressure design class defined in ASME B16.5 and used for reference purposes
NOTE The ANSI rating class is designated by the word “Class” followed by a number.
[ISO 14313:1999]
3.2
bi-directional valve
valve designed for blocking the fluid in both downstream and upstream directions
[ISO 14313:1999]
3.3
bleed
drain or vent
[ISO 14313:1999]
3.4
block valve
ball or gate valve that blocks flow into the downstream conduit when in the closed position
NOTE 1 Valves are either single- or double-seated, bi-directional or uni-directional.
NOTE 2 Adapted from ISO 14313:1999.
3.5
breakaway thrust [torque]
thrust [torque] required for opening a valve with maximum pressure differential
NOTE Adapted from ISO 14313:1999.
3.6
by agreement
agreed between manufacturer and purchaser
[ISO 14313:1999]
3.7
double-block-and-bleed valve
valve with two seating surfaces which, in the closed position, blocks flow from both valve ends when the cavity
between the seating surfaces is vented through a bleed connection provided on the body cavity
[ISO 14313:1999]
3.8
drive train
all parts of a valve drive between the operator and the obturator, including the obturator but excluding the operator
[ISO 14313:1999]
© ISO 2001 – All rights reserved 3

---------------------- Page: 13 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
3.9
flow coefficient
q
v
volumetric flowrate of water at a temperature between 5 °C (40 °F) and 40 °C (104 °F) passing through a valve and
resulting in a pressure loss of 100 kPa (14,7 psi)
NOTE 1 It is expressed in cubic metres per hour.
NOTE 2 q relates to the flowrate coefficient C in US gallons per minute at 15,6 °C (60 °F) resulting in 1 psi pressure drop as

v v
follows:
C
v
q =
v
1,156
NOTE 3 Adapted from ISO 14313:1999.
3.10
full-opening valve
valve with an unobstructed opening capable of allowing a sphere or other internal device for the same nominal size
as the valve to pass
[ISO 14313:1999]
3.11
handwheel
wheel consisting of a rim connected to a hub, for example by spokes, and used to operate manually a valve
requiring multiple turns
[ISO 14313:1999]
3.12
locking device
part or an arrangement of parts for securing a valve in the open and/or closed position
[ISO 14313:1999]
3.13
manual operator
wrench (lever) or handwheel with or without a gearbox
[ISO 14313:1999]
3.14
maximum pressure differential
MPD
maximum difference between the upstream and downstream pressures across the obturator at which the obturator
may be operated
NOTE Adapted from ISO 14313:1999.
3.15
nominal pipe size
NPS
numerical inches designation of size which is common to components in piping systems of any one size
NOTE The nominal pipe size is designated by the letters NPS followed by a number
[ISO 14313:1999]
4 © ISO 2001 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 14723:2004
ISO 14723:2001(E)
3.16
nominal pressure class
PN class
numerical pressure design class as defined in ISO 7005-1 and used for reference purposes
NOTE The nominal pressure class is designated by the letters PN followed by a number.
[ISO 14313:1999]
3.17
nominal size
DN
numerical metric designation of size which is common to components in piping systems of any one size
NOTE  Nominal size is designated by the letters DN followed by a number.
[ISO 14313:1999]
3.18
obturator
closure member
part of a valve which is positioned in the flow stream to permit or block flow
EXAMPLE Ball, clapper, disc, gate or plug.
NOTE Adapted from ISO 14313:1999.
3.19
operator
device (or assembly)
...