SIST EN ISO 7233:2009
(Main)Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006)
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006)
This International Standard specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows: method A - for hoses of nominal bore up to and including 80 mm; - method B - for hoses of nominal bore greater than 80 mm; - method C - for hoses of all dimensions. Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall hose or hose assembly.
Gummi- und Kunststoffschläuche und Schlauchleitungen - Bestimmung der Beständigkeit gegen Vakuum (ISO 7233:2006)
Diese Internationale Norm legt drei Verfahren zur Bestimmung der Vakuumbeständigkeit von Schläuchen und Schlauchleitungen gefertigt aus Kunststoff oder Gummi fest. Geeignete Abmessungen von Schläuchen für jedes Verfahren sind die im Folgenden genannten:
Verfahren A : Für Schläuche mit einem Nenn-Innendurchmesser bis einschließlich 80 mm;
Verfahren B : Für Schläuche mit einem Nenn-Innendurchmesser größer 80 mm;
Verfahren C : Für Schläuche aller Abmessungen.
Verfahren A und B können auch zur Prüfung der Anhaftung zwischen innerer Schicht und Verstärkungselement (Ablösung) in der Länge eines Schlauches mit Wendel oder einer Schlauchleitung genutzt werden
Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la résistance a l'aspiration (ISO 7233:2006)
L'ISO 7233:2006 spécifie trois méthodes pour la détermination de la résistance à l'aspiration des tuyaux et des flexibles fabriqués à partir de caoutchouc ou de plastique. Les dimensions s'appliquant aux tuyaux pour chaque méthode sont les suivantes:
méthode A — pour tuyaux de diamètre intérieur nominal inférieur ou égal à 80 mm;
méthode B — pour tuyaux de diamètre intérieur nominal supérieur à 80 mm;
méthode C — pour tuyaux de toutes dimensions.
Les méthodes A et B peuvent également être utilisées pour vérifier l'adhérence entre le tube intérieur et le renforcement (délamination) dans une longueur de tuyau ou de flexible de raccordement renforcé.
Gumene in polimerne cevi ter cevni priključki - Ugotavljanje odpornosti na vakuum (ISO 7233:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7233:2009
01-februar-2009
1DGRPHãþD
SIST EN ISO 7233:2000
*XPHQHLQSROLPHUQHFHYLWHUFHYQLSULNOMXþNL8JRWDYOMDQMHRGSRUQRVWLQDYDNXXP
,62
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum
(ISO 7233:2006)
Gummi- und Kunststoffschläuche und Schlauchleitungen - Bestimmung der
Beständigkeit gegen Vakuum (ISO 7233:2006)
Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la résistance a
l'aspiration (ISO 7233:2006)
Ta slovenski standard je istoveten z: EN ISO 7233:2008
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 7233:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7233:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 7233:2009
EUROPEAN STANDARD
EN ISO 7233
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2008
ICS 23.040.70 Supersedes EN ISO 7233:1995
English Version
Rubber and plastics hoses and hose assemblies - Determination
of resistance to vacuum (ISO 7233:2006)
Tuyaux et flexibles en caoutchouc et en plastique - Gummi- und Kunststoffschläuche und -schlauchleitungen -
Détermination de la résistance à l'aspiration (ISO Bestimmung der Beständigkeit gegen Vakuum (ISO
7233:2006) 7233:2006)
This European Standard was approved by CEN on 26 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7233:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7233:2009
EN ISO 7233:2008 (E)
Foreword
The text of ISO 7233:2006 has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 7233:2008 by Technical Committee CEN/TC 218 "Rubber and plastics hoses
and hose assemblies", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2008, and conflicting national standards
shall be withdrawn at the latest by July 2008.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any
or all such patent rights.
This document supersedes EN ISO 7233:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of ISO 7233:2006 has been approved by CEN as EN ISO 7233:2008 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7233:2009
INTERNATIONAL ISO
STANDARD 7233
Third edition
2006-02-01
Rubber and plastics hoses and hose
assemblies — Determination of
resistance to vacuum
Tuyaux et flexibles en caoutchouc et en plastique — Détermination de
la résistance à l'aspiration
Reference number
ISO 7233:2006(E)
©
ISO 2006
---------------------- Page: 5 ----------------------
SIST EN ISO 7233:2009
ISO 7233:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 7233:2009
ISO 7233:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Principle. 1
4 Apparatus . 1
5 Test pieces . 2
6 Conditioning of test pieces. 2
7 Test pressure . 2
8 Procedure (method A) . 2
9 Procedure (method B) . 2
10 Procedure (method C) . 2
11 Test report . 4
Bibliography . 5
© ISO 2006 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 7233:2009
ISO 7233:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.