SIST EN 15283-1:2008+A1:2009
(Main)Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement
Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement
This European Standard specifies the characteristics and performance of gypsum boards with mat reinforcement intended to be used in building construction works including those intended for secondary manufacturing operations. It includes boards designed to receive either direct surface decoration or gypsum plaster.
Gypsum boards with mat reinforcement are selected for use according to their type, size, thickness and edge profile. The boards can be used for example to provide dry lining finishes to walls, to fixed and suspended ceilings, to partitions, or as cladding to structural columns and beams. Other uses can be for floors, ventilation and smoke extraction ducts, cable trays and sheathing applications.
This European Standard covers the following product performance characteristics: reaction to fire, water vapour permeability, flexural strength, and thermal resistance.
The following performance characteristics are linked to systems assembled with gypsum boards with mat reinforcement: shear strength, fire resistance, impact resistance, direct airborne sound insulation, acoustic absorption. If required, tests should be done according to the corresponding European test methods on assembled systems simulating the end use conditions.
This European Standard also covers additional technical characteristics that are of importance for the use and acceptance of the product and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this EN.
This European Standard does not cover gypsum boards with mat reinforcement which have been subject to any secondary manufacturing operations (e.g. insulating composite panels, boards with thin lamination etc.).
Products covered by EN 520 or EN 13815 are excluded.
Faserverstärkte Gipsplatten - Begriffe, Anforderungen und Prüfverfahren - Teil 1: Gipsplatten mit Vliesarmierung
Plaques de plâtre armées de fibres - Définitions, spécifications et méthodes d'essai - Partie 1: Plaques de plâtre armées d'un tissu
La présente Norme européenne spécifie les caractéristiques et performances des plaques de plâtre armées de tissu
conçues pour être utilisées dans des ouvrages de construction, y compris dans des opérations de fabrication
secondaires. Il inclut les plaques destinées à recevoir directement une finition sur leur face ou un enduit au plâtre.
Les plaques de plâtre sont sélectionnées pour leur utilisation conformément à leur type, taille, épaisseur et profil des
bords. Les plaques peuvent être utilisées par exemple pour créer une finition par habillage des murs, des plafonds
fixes et suspendus, des cloisons, ou pour la protection et l’habillage des poteaux et des poutres. Elles peuvent par
ailleurs être utilisées pour les sols, la ventilation et les conduits de désenfumage, les chemins de câble et la pose
sous bardage.
La présente Norme européenne couvre les caractéristiques de performance suivantes : réaction au feu, perméabilité
à la vapeur d’eau, résistance à la flexion et résistance thermique.
Les caractéristiques de performance suivantes sont liées aux systèmes assemblés à l’aide de plaques de plâtre
armées de tissu : résistance au cisaillement, au choc, isolation acoustique aux bruits aériens, absorption acoustique.
Au besoin, il convient d’effectuer des essais selon les méthodes d'essai européennes correspondantes sur
des systèmes assemblés qui simulent les conditions d'utilisation finale.
Elle couvre également les caractéristiques techniques supplémentaires qui sont importantes en vue de l’utilisation
et de l’acceptation du produit ainsi que les essais de référence de ces caractéristiques. Elle traite de l’évaluation de la
conformité des produits à la présente Norme.
La présente Norme européenne ne couvre pas les plaques de plâtre armées de tissu qui ont subi des opérations
de transformation secondaires (par exemple les complexes d'isolation, les plaques avec revêtements minces, etc.).
Les produits traités par l’EN 520 ou l’EN 13815 sont exclus.
Mavčne plošče, ojačene z vlakni - Definicije, zahteve in preskusne metode - 1. del: Mavčne plošče, ojačene z mrežo iz vlaken
General Information
Relations
Overview
EN 15283-1:2008+A1:2009 is the CEN European standard that defines gypsum boards with mat (fibrous) reinforcement - their definitions, requirements and reference test methods (Part 1: gypsum boards with mat reinforcement). It covers boards intended for building construction works (including secondary manufacturing operations where not altering the board itself) and boards designed to receive direct surface decoration or gypsum plaster. The document includes characteristics, conformity evaluation and guidance for CE marking under EU construction product rules.
Key topics and technical requirements
- Product scope and definitions - composition (gypsum core bonded to woven/non‑woven fibre mat), board types and designations (e.g. GM, GM‑H1/H2, GM‑I, GM‑F).
- Performance characteristics covered:
- Reaction to fire (classification using reaction-to-fire tests)
- Water vapour permeability (water vapour resistance factor)
- Flexural strength and deflection properties
- Thermal resistance (thermal conductivity)
- Additional board properties and optional types: reduced water absorption, enhanced surface hardness, improved high‑temperature core cohesion, enhanced strength.
- Reference test methods and sampling - dimensional checks (length, width, thickness, squareness), flexural breaking load, deflection, total water absorption, surface hardness, impact resistance and other standardised test procedures.
- System‑level characteristics (assessed on assembled systems simulating end use): shear strength, fire resistance, impact resistance, airborne sound insulation, acoustic absorption.
- Conformity and factory production control - initial type testing, ongoing FPC and marking/labeling requirements (including CE marking provisions referenced in Annex ZA).
Practical applications
Gypsum boards with mat reinforcement (mat‑reinforced gypsum boards) are used where fire protection, acoustic performance, thermal insulation or mechanical strength are required. Typical applications:
- Dry lining finishes for walls and partitions
- Fixed and suspended ceilings
- Cladding for structural columns and beams
- Floors, ventilation and smoke-extraction ducts, cable trays and sheathing
- Boards suitable for direct decoration or plaster finishing
Who uses this standard
- Manufacturers of gypsum boards (product specification, quality control, CE marking)
- Architects and specifiers (selecting appropriate board types by performance)
- Contractors and installers (ensuring correct board selection and handling)
- Test laboratories and conformity assessment bodies (testing to referenced methods)
- Product certification bodies and regulators
Related standards
- EN 520, EN 13815 (other gypsum product standards - note: products covered by these are excluded)
- EN 13501‑1 / EN 13501‑2, EN 13823 (fire testing/classification)
- EN ISO 12572 (water vapour transmission), EN 12664 (thermal resistance)
- EN ISO 140‑3, EN ISO 717‑1, EN ISO 354 (acoustics)
- EN 14195, EN 13963, ISO 7892, EN ISO 9001
This standard is essential when specifying or testing mat‑reinforced gypsum boards to ensure compliance with European performance and conformity requirements.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Faserverstärkte Gipsplatten - Begriffe, Anforderungen und Prüfverfahren - Teil 1: Gipsplatten mit VliesarmierungPlaques de plâtre armées de fibres - Définitions, spécifications et méthodes d'essai - Partie 1: Plaques de plâtre armées d'un tissuGypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. Mortar01.040.91Gradbeni materiali in gradnja (Slovarji)Construction materials and building (Vocabularies)ICS:Ta slovenski standard je istoveten z:EN 15283-1:2008+A1:2009SIST EN 15283-1:2008+A1:2009en,fr,de01-december-2009SIST EN 15283-1:2008+A1:2009SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15283-1:2008+A1
August 2009 ICS 01.040.91; 91.100.10 Supersedes EN 15283-1:2008English Version
Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement
Plaques de plâtre armées de fibres - Définitions, spécifications et méthodes d'essai - Partie 1: Plaques de plâtre armées d'un tissu
Faserverstärkte Gipsplatten - Begriffe, Anforderungen und Prüfverfahren - Teil 1: Gipsplatten mit Vliesarmierung This European Standard was approved by CEN on 28 December 2007 and includes Amendment 1 approved by CEN on 20 July 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15283-1:2008+A1:2009: ESIST EN 15283-1:2008+A1:2009
Sampling procedure for testing . 28A.1 General . 28A.2 Sampling procedure . 28Annex B (normative)
Mounting and fixing for testing according to EN 13823 (SBI test) . 30B.1 General applications . 30B.2 Limited applications regarding joint filling . 32B.3 Limited applications regarding wood based substrates . 33SIST EN 15283-1:2008+A1:2009
Clauses of this European Standard addressing the provisions of EU Construction Products Directive . 34ZA.1 Scope and relevant characteristics . 34ZA.2 Procedure of attestation of conformity of gypsum boards with mat reinforcement . 36ZA.3 CE marking and labelling. 39 SIST EN 15283-1:2008+A1:2009
Diagram 1 — Families of gypsum products SIST EN 15283-1:2008+A1:2009
Diagram 2 — Family of ancillary products SIST EN 15283-1:2008+A1:2009
www.company.com " 4 Requirements 4.1 Mechanical characteristics 4.1.1 Flexural strength The flexural strength shall be expressed as the breaking load in Newtons. The flexural breaking load of gypsum boards with mat reinforcement determined in accordance with the test method described in 5.6 shall not be less than the values given below, where t is the thickness of the board in mm. !Table 2" — Flexural breaking load in Newtons Type Nominal board thickness Flexural breaking load mm N
Transverse direction Longitudinal direction GM, GM-H1, GM-H2, GM-I, GM-F
t 16,8 ⋅ t 43 ⋅ t GM-R t 24 ⋅ t 58 ⋅ t Additionally, no individual result shall be more than 10 % below these values. 4.1.2 Deflection under load When required and subject to regulatory requirements, the deflection under load shall be determined in accordance to the test method described in 5.7. SIST EN 15283-1:2008+A1:2009
The thickness shall be measured as described in 5.4 and compared to the nominal thickness. Tolerances for thickness below 18 mm shall be ± 0,7 mm. For boards of thickness equal to or greater than 18 mm, the tolerance shall be ± (0,04 x thickness) (in mm). The difference between individual thickness measurements on any individual board shall not exceed 0,8 mm. 4.7.4 Squareness The deviation from squareness measured as described in 5.5 shall not exceed 2,5 mm per metre of width. 4.7.5 Edge and end profiles The edge and end profiles may vary widely depending upon the jointing system and decorative and aesthetic considerations. SIST EN 15283-1:2008+A1:2009
Figure 1 — Determination of width 5.2.4 Expression of results Each measured value expressed in millimetres is recorded. 5.3 Determination of length 5.3.1 Principle The length is measured at three points. 5.3.2 Apparatus A metal rule or tape with reading to 1 mm divisions. SIST EN 15283-1:2008+A1:2009
Figure 2 — Determination of length 5.3.3 Procedure Take three measurements between the extremities of the board (see Figure 2) to the nearest millimetre, one near each edge and one near the middle. 5.3.4 Expression of results Each measured value expressed in millimetres is recorded and compared to the nominal length of the board. 5.4 Determination of thickness 5.4.1 Principle The thickness of the board is measured at six points near to one end of the board. 5.4.2 Apparatus A micrometer, dial gauge, or callipers with an anvil diameter not less than 10 mm and permitting a reading to 0,05 mm. 5.4.3 Procedure Take six measurements (see Figure 3) to the nearest 0,05 mm across one end at approximately equal intervals across the width and at least 25 mm from the end and 100 mm from the edges. For boards of nominal width not greater than 600 mm, three measurements are sufficient. SIST EN 15283-1:2008+A1:2009
Figure 3 — Determination of thickness 5.4.4 Expression of results Record each individual measurement. Record to the nearest 0,1 mm the thickness as the average of the values obtained for each board. 5.5 Determination of squareness 5.5.1 Principle Method a: Two boards are compared with each other and the squareness measured. Method b: The two diagonals of a board are measured. 5.5.2 Apparatus A metal rule or tape with 1 mm divisions. 5.5.3 Procedure Method a: Place one board on top of another so that they coincide along one edge and at one corner (circled in Figure 4.). Measure to the nearest 1 mm the distance ∆1 (see Figure 4) between the ends of the opposite edges. Turn the top board over so that the same ends coincide as for the first measurement and ensure that the corner of the top board coincides with that corner of the lower board used in the first measurement (circled in Figure 4). Measure the new distance ∆2 between the ends of the opposite edges. SIST EN 15283-1:2008+A1:2009
Figure 4 — Determination of squareness of ends Method b: Measure the length (l) and the width (w) of the board and the lengths of the two diagonals d1 and d2 to the nearest mm. 5.5.4 Expression of results Method a: The squareness is characterised for one of the boards by the half sum w221∆∆+ and for other by the half difference w212∆∆+ expressed in millimetres per metre. Method b: The squareness S is expressed by the result of the expression: wlddddS.4)21(.)21(−+= (1) For the calculations, the width (w) shall be expressed in metres, all other parameters in millimetres. SIST EN 15283-1:2008+A1:2009
...
Frequently Asked Questions
SIST EN 15283-1:2008+A1:2009 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement". This standard covers: This European Standard specifies the characteristics and performance of gypsum boards with mat reinforcement intended to be used in building construction works including those intended for secondary manufacturing operations. It includes boards designed to receive either direct surface decoration or gypsum plaster. Gypsum boards with mat reinforcement are selected for use according to their type, size, thickness and edge profile. The boards can be used for example to provide dry lining finishes to walls, to fixed and suspended ceilings, to partitions, or as cladding to structural columns and beams. Other uses can be for floors, ventilation and smoke extraction ducts, cable trays and sheathing applications. This European Standard covers the following product performance characteristics: reaction to fire, water vapour permeability, flexural strength, and thermal resistance. The following performance characteristics are linked to systems assembled with gypsum boards with mat reinforcement: shear strength, fire resistance, impact resistance, direct airborne sound insulation, acoustic absorption. If required, tests should be done according to the corresponding European test methods on assembled systems simulating the end use conditions. This European Standard also covers additional technical characteristics that are of importance for the use and acceptance of the product and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this EN. This European Standard does not cover gypsum boards with mat reinforcement which have been subject to any secondary manufacturing operations (e.g. insulating composite panels, boards with thin lamination etc.). Products covered by EN 520 or EN 13815 are excluded.
This European Standard specifies the characteristics and performance of gypsum boards with mat reinforcement intended to be used in building construction works including those intended for secondary manufacturing operations. It includes boards designed to receive either direct surface decoration or gypsum plaster. Gypsum boards with mat reinforcement are selected for use according to their type, size, thickness and edge profile. The boards can be used for example to provide dry lining finishes to walls, to fixed and suspended ceilings, to partitions, or as cladding to structural columns and beams. Other uses can be for floors, ventilation and smoke extraction ducts, cable trays and sheathing applications. This European Standard covers the following product performance characteristics: reaction to fire, water vapour permeability, flexural strength, and thermal resistance. The following performance characteristics are linked to systems assembled with gypsum boards with mat reinforcement: shear strength, fire resistance, impact resistance, direct airborne sound insulation, acoustic absorption. If required, tests should be done according to the corresponding European test methods on assembled systems simulating the end use conditions. This European Standard also covers additional technical characteristics that are of importance for the use and acceptance of the product and the reference tests for these characteristics. It provides for the evaluation of conformity of the product to this EN. This European Standard does not cover gypsum boards with mat reinforcement which have been subject to any secondary manufacturing operations (e.g. insulating composite panels, boards with thin lamination etc.). Products covered by EN 520 or EN 13815 are excluded.
SIST EN 15283-1:2008+A1:2009 is classified under the following ICS (International Classification for Standards) categories: 01.040.91 - Construction materials and building (Vocabularies); 91.100.10 - Cement. Gypsum. Lime. Mortar. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 15283-1:2008+A1:2009 has the following relationships with other standards: It is inter standard links to SIST EN 15283-1:2008. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 15283-1:2008+A1:2009 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC; Standardization Mandates: M/106. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 15283-1:2008+A1:2009 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
The article discusses the specifications and performance of gypsum boards with mat reinforcement. These boards are commonly used in building construction for various purposes such as dry lining finishes, ceilings, partitions, and cladding. The article highlights the product performance characteristics including reaction to fire, water vapor permeability, flexural strength, and thermal resistance. It also mentions that other performance characteristics like shear strength, fire resistance, impact resistance, sound insulation, and acoustic absorption are dependent on the assembled systems. The article excludes gypsum boards with mat reinforcement that have undergone secondary manufacturing operations and also excludes products covered by EN 520 or EN 13815.
この記事は、マット補強された石膏ボードの仕様と性能について説明しています。これらのボードは建築工事に使用され、壁のドライライニング仕上げ、天井の固定および浮上天井仕上げ、パーティション、構造用柱および梁のクラッディングなどの用途に適しています。この記事では、製品の性能特性として、耐火性、水蒸気透過性、曲げ強さ、熱抵抗が述べられています。また、システムに組み立てられたマット補強石膏ボードに関連する性能特性として、せん断強度、耐火性、耐衝撃性、直接空中音遮断性、音響吸収性が挙げられます。必要に応じて、最終使用条件を模擬した組み立てられたシステム上での対応する欧州の試験方法に従ってテストを行う必要があります。この記事では、製品の使用と受け入れに重要な追加の技術的特性についても取り上げ、これらの特性の参照テスト方法を提供しています。この記事では、二次的な製造工程（断熱コンポジットパネル、薄い積層板など）が施されたマット補強石膏ボードは対象外とされており、EN 520またはEN 13815でカバーされる製品も対象外とされています。
이 기사는 매트 보강이 된 석고 보드의 사양과 성능에 대해 설명하고 있습니다. 이러한 보드는 건설 작업을 위해 사용되며, 벽에 건식 마감재로, 천장의 고정 및 중량 천정재로, 파티션으로, 구조 기둥 및 빔의 클래딩으로 사용될 수 있습니다. 이 기사는 화재 반응, 수증기 투과성, 굴곡 강도, 열 저항력과 같은 제품 성능 특성을 다루고 있습니다. 또한 교반된 시스템에 따라 전달되는 전달 기능, 화재 저항, 충격 저항, 직접 공기중 소음 차단, 음향 흡수와 같은 성능 특성이 언급됩니다. 이러한 특성은 최종 사용 조건을 모방하는 조립된 시스템에 대한 테스트에 따라 결정됩니다. 이 기사는 추가적으로 제품의 사용과 수용에 중요한 기술적 특성을 다루고 있으며, 이러한 특성에 대한 참조 테스트를 제공합니다. 이 기사에서는 이중 제조 작업을 거친 석고 보드와 EN 520 또는 EN 13815로 커버되는 제품은 제외되었습니다.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...