oSIST prEN ISO 12643-2:2014
(Main)Graphic technology - Safety requirements for graphic technology equipment and systems - Part 2: Prepress and press equipment and systems (ISO/DIS 12643-2:2014)
Graphic technology - Safety requirements for graphic technology equipment and systems - Part 2: Prepress and press equipment and systems (ISO/DIS 12643-2:2014)
This standard provides safety requirements specific to prepress and press equipment and systems. It is intended to be used in conjunction with the general requirements given in EN ISO 12643-1.
This standard provides additional safety requirements for the design and construction of new prepress and press equipment, and the auxiliary equipment integrated into the press control system.
Graphische Technik — Sicherheitsanforderungen an Ausrüstungen und Systeme der graphischen Technik — Teil 2: Ausrüstungen und Systeme in der Druckvorstufe und im Druckbereich (ISO/DIS 12643-2:2014)
Technologie graphique - Exigences de sécurité pour les systèmes et l'équipement de technologie graphique - Partie 2: Systèmes et équipement pour la préimpression et la presse (ISO/DIS 12643-2:2014)
Grafična tehnologija - Varnostne zahteve za grafično tehnološko opremo in sisteme - 2. del: Grafična priprava in tiskarska oprema ter sistemi (ISO/DIS 12643-2:2014)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 12643-2:2014
01-september-2014
*UDILþQDWHKQRORJLMD9DUQRVWQH]DKWHYH]DJUDILþQRWHKQRORãNRRSUHPRLQ
VLVWHPHGHO *UDILþQDSULSUDYDLQWLVNDUVNDRSUHPDWHUVLVWHPL ,62',6
Graphic technology - Safety requirements for graphic technology equipment and systems
- Part 2: Prepress and press equipment and systems (ISO/DIS 12643-2:2014)
Technologie graphique - Exigences de sécurité pour les systèmes et l'équipement de
technologie graphique - Partie 2: Systèmes et équipement pour la préimpression et la
presse (ISO/DIS 12643-2:2014)
Ta slovenski standard je istoveten z: prEN ISO 12643-2
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
oSIST prEN ISO 12643-2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 12643-2:2014
---------------------- Page: 2 ----------------------
oSIST prEN ISO 12643-2:2014
DRAFT INTERNATIONAL STANDARD
ISO/DIS 12643-2
ISO/TC 130 Secretariat: SAC
Voting begins on: Voting terminates on:
2014-05-22 2014-10-22
Graphic technology — Safety requirements for graphic
technology equipment and systems —
Part 2:
Prepress and press equipment and systems
Technologie graphique — Exigences de sécurité pour les systèmes et l’équipement de technologie
graphique —
Partie 2: Systèmes et équipement pour la préimpression et la presse
ICS: 37.100.10
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 12643-2:2014(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2014
---------------------- Page: 3 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2:2014(E)
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
Contents Page
Foreword . v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Conformity with this part of ISO 12643 . 4
5 Equipment subject to requirements . 5
5.1 General . 5
5.2 Prepress equipment . 5
5.3 Printing presses and coating/varnishing machines . 5
5.4 Other equipment covered by this part of ISO 12643 . 6
6 Safety requirements and/or protective measures . 7
6.1 General . 7
6.2 Guarding of significant hazards . 7
6.3 Interlocks . 8
6.4 Hold-to-run controls . 9
6.5 Automatic format-setting operations . 10
6.6 Additional safeguarding methods for machine devices and components . 10
7 Changing of printing plates . 24
7.1 General . 24
7.2 Automatic printing plate changes . 24
7.3 Semi-automatic printing plate changes . 25
8 Requirements for protection against other hazards . 25
8.1 General . 25
8.2 Protection against fire and explosion in continuous-flow devices . 25
8.3 Explosion protection exceptions . 27
8.4 Spillage from washing devices . 27
8.5 Working platforms, access stairs, passageways and raised workplaces . 28
8.6 Electrostatic toner dust . 28
8.7 Washing equipment for printing plates, rollers and doctor blades . 28
8.8 Alcohol dosing devices . 29
8.9 Refrigerating devices in ink and dampening units . 29
8.10 Powder-spraying devices . 29
8.11 Hazardous emissions of sheet-fed presses . 29
8.12 Large-format ink jet digital printing machines (wide-format ink jet digital printing
machines) . 30
8.13 Noise control requirements on web offset printing presses . 30
8.14 Dust protection requirements on web offset printing presses . 31
8.15 Emergency stop and stop/safe devices at stationary control stands of web offset printing
presses . 31
8.16 Cableless motion control . 31
9 Additional requirements for functions, operations, colours and mechanical specifications
of manual control devices . 31
9.1 General . 31
9.2 Emergency stop and ink, dampening, metering, coating or fountain rollers . 31
9.3 Emergency stop on auxiliary draw nips . 31
9.4 Alternative controls for stop/safe function on sheet-fed presses . 31
© ISO 2014 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
9.5 Ready control . 32
9.6 Speed limit control . 32
9.7 Plate position control . 32
9.8 Colours for manual control devices . 33
10 Control systems for screen printing presses . 33
11 Safety requirements for prepress equipment . 33
11.1 Electrical equipment of prepress machinery . 33
11.2 Electric/electronic control systems of prepress machinery . 33
11.3 Exposing equipment . 34
11.4 Safeguarding the discharge of liquids . 34
11.5 Safeguarding in-running nips on engraving machines . 34
11.6 Safeguarding against copper swarf hazard . 34
11.7 Safeguarding bending unit on printing plate bending machines . 34
11.8 Safeguarding printing plate punching devices . 34
12 Signals and warning devices . 34
13 Control zones for web presses having multiple folders . 35
14 Verification of safety requirements and/or protective measures . 36
15 Contents of instruction handbook . 36
15.1 General . 36
15.2 Sheet-fed printing press systems . 36
15.3 Web-fed printing press systems . 36
15.4 Screen printing presses . 37
15.5 Automatic cylinder and roller washing device . 37
15.6 Continuous-flow drying devices . 38
15.7 Oxidizers, incinerators and thermal cleaning plants . 38
15.8 Alcohol dosing devices . 38
15.9 Washing equipment for printing plates . 39
15.10 Prepress machinery . 39
15.11 Large –format inkjet digital printing machines . 39
Annex A (informative) List of significant hazards . 40
Annex B (informative) Emission levels of sheet-fed presses resulting from tests conducted in
Europe . 44
Bibliography . 50
iv © ISO 2014 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12643-2 was prepared by Technical Committee ISO/TC 130, Graphic technology.
This third edition of ISO 12643-2 constitutes a technical revision of the second edition (ISO-12643-2:2010).
Significant changes incorporated into this third edition include, but are not limited to, the following:
addition of Clause 8.12 Large-format ink jet digital printing machines (wide-format ink jet digital printing
machines)
addition of Clause 9.2 Emergency stop locations
addition of Clause 14, Verification of safety requirements and/or protective measures
addition of Clause 15.11 Information for use in the instruction handbook
reorganization of clauses to align with requirements in ISO Guide 78, Safety of machinery – Rules for
drafting and presentation of safety standards.
It is the intent of ISO/TC 130 that there be a transition period between the second and third editions of
ISO 12643-2. The user is referred to Clause 4 of this standard for guidance in this area.
As from 2014-01-01, ISO 12643-2:2014 will cancel and replace ISO 12643-2:2010. Accordingly, as from
2014-01-01, only ISO 12643-2:2014 will be applicable to new equipment manufactured.
ISO 12643 consists of the following parts, under the general title Graphic technology — Safety requirements
for graphic technology equipment and systems:
Part 1: General requirements
Part 2: Prepress and press equipment and systems
Part 3: Binding and finishing equipment and systems
Part 4: Converting equipment and systems
Part 5: Stand-alone platen presses
© ISO 2014 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
Introduction
This part of ISO 12643 is a type-C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope and Clause 5 of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
During the development of this part of ISO 12643, existing relevant standards of other countries were taken
into consideration. An effort has been made to harmonize the requirements of all countries, recognizing that
national standards or laws may dictate national requirements. In cases where it was known that there is a
national requirement that differs from this part of ISO 12643, that has been noted.
This part of ISO 12643 was developed to harmonize the requirements of the following US and European
safety standards:
ANSI B65-1, Graphic technology — Safety requirements for graphic technology equipment and
systems — Part 1: General requirements
ANSI B65-2, Graphic technology — Safety requirements for graphic technology equipment and
systems — Part 2: Prepress and press equipment and systems
EN 1010-1, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 1: Common requirements
EN 1010-2, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 2: Printing and varnishing machines including pre-press machinery
vi © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 12643-2:2014
DRAFT INTERNATIONAL STANDARD ISO/DIS 12643-2
Graphic technology — Safety requirements for graphic
technology equipment and systems —
Part 2:
Prepress and press equipment and systems
1 Scope
This part of ISO 12643 provides safety requirements specific to prepress and press equipment and systems. It
is intended to be used in conjunction with the general requirements given in ISO 12643-1.
This part of ISO 12643 provides additional safety requirements for the design and construction of new
prepress and press equipment, and the auxiliary equipment integrated into the press control system.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 12100, Safety of Machinery - General Principles for Design - Risk Assessment and Risk Reduction
ISO 12643-1, Graphic technology — Safety requirements for graphic technology equipment and systems —
Part 1: General requirements
ISO 13732-1, Ergonomics of the thermal environment — Methods for the assessment of human responses to
contact with surfaces — Part 1: Hot surfaces
ISO 13849-1, Safety of machinery — Safety-related parts of control systems — Part 1: General principles for
design
ISO 13855, Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of
the human body
ISO 13857, Safety of machinery — Safety distances to prevent hazard zones being reached by upper and
lower limbs
IEC 62061, Safety of machinery — Functional safety of safety-related electrical, electronic and programmable
electronic control systems
EN 378-1, Refrigerating systems and heat pumps — Safety and environmental requirements — Part 1: Basic
requirements, definitions, classification and selection criteria
EN 1539, Dryers and ovens in which flammable substances are released — Safety requirements
© ISO 2014 – All rights reserved 1
---------------------- Page: 9 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12643-1, ISO 13849-1 and the
following apply.
3.1
access height
sheet-fed press delivery zone dimension of the maximum opening into the area below the sheet gripper,
measured between the access level (floor, fixed platform or footboard) and the lower edge of fixed machine
parts (e.g. fixed guard, fixed cover, fixed parts such as a sheet stop)
NOTE 1 to entry See Figure 1.
3.2
alcohol dosing device
mechanism used to regulate the amount of alcohol in the dampening water of offset printing presses
3.3
automatic plate-clamping device
mechanism used to secure a printing plate during the automatic or semi-automatic changing of the plates
3.4
bypass
temporary, time-limited suppression of one or more safety functions through the use of safety-relevant parts of
a control system
3.5
coating unit
coater
machine that applies a predetermined thickness of a liquid substance (e.g. glue, varnish, ink, etc.) on
substrates made of paper or a similar material
3.6
continuous-flow drying device
mechanism built into printing presses to dry and cure inks and coatings that have been applied to substrates
EXAMPLE Hot air, IR or UV radiation.
3.7
crawl speed
continuous movement at a steady slow speed, and initiated by a momentary contact control
3.8
cylinder screen printing press
sheet-fed machine in which the substrate (sheet) to be printed is pressed against the screen by an impression
cylinder
3.9
digital printing machine
machine used in commercial/industrial applications where the printing image is produced in the machine from
data stored in digital form and transferred to the substrate without the use of a printing plate
NOTE 1 to entry This includes digital printing presses and wide-format ink jet printing devices.
3.10
draw roller
power-driven roller that pulls a substrate
2 © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
3.11
enabling device
mechanism that needs to be in a specified state or condition in order for a second actuator or device to start a
machine under hold-to-run control, and which will stop machine movement as soon as one of the hold-to-run
controls is released or the status of the mechanism changes
3.12
forms printing press
leporello printing press
machine for the production of continuous forms where paper webs printed with one or more colours are
accordion-folded or wound onto a reel
NOTE 1 to entry In addition to the printing section, the machine consists of devices for punching, remaliners (sprocket
punching), cross-perforation, longitudinal perforation and leporello (zig-zag) folding.
3.13
gravure printing machine
machine consisting of a printing cylinder; an inking system, in which ink is applied to the printing cylinder by an
ink roll or spray and the excess is removed by a doctor blade (device for scraping excess ink off a
gravure cylinder); and an impression cylinder covered with a rubber composition, which presses the substrate
into contact with the ink in the cells of the printing cylinder
3.14
pile turner
device attached to sheet-fed printing presses and used to turn piles of printed paper for further processing,
such as back-printing on a second run
3.15
powder-spraying device
equipment used to spray powder onto the printed material on the delivery side of sheet-fed printing presses
3.16
prepress equipment
machines used in the first stage of the graphic technology workflow, prior to printing, that include all the
operations necessary for the preparation of images and image carriers
NOTE 1 to entry Adapted from ISO 12637-1.
3.17
press system
printing press and a series of machines that supply substrate into and through the printing press and guide or
direct the substrate to a cutting, folding or delivery device that delivers the product to the last working station
integrated with the printing press control system
3.18
printing plate
base material that stores the image to be printed (pictures and/or text) and transfers ink onto a substrate, thus
printing the image
3.19
printing table
supportive surface to hold the substrate to be printed during the printing process (as on certain types of
screen printing presses)
3.20
proofing press
machine with manual feeding and delivery used for printing a small number of copies, and generally used for
assessing print quality before the printing plate is mounted in the production machine
© ISO 2014 – All rights reserved 3
---------------------- Page: 11 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
3.21
reel turner
device used to turn reels (webs) of substrate for easier handling, e.g. for correct positioning of the reel when
feeding webs to printing presses
3.22
screen frame
device for taking up the printing screen
3.23
screen printing press
machine using printing plates with woven material (sieve-like screens) that partially allow ink to penetrate
through the material
3.24
sheet-fed press
machine for printing sheet-size substrates, including proofing presses, in which sheets may be fed by feeders
(automatic or manual), or from sheeters attached to unwinding units
3.25
speed limit
control that, when activated, prevents acceleration of machine motion
3.26
washing device
equipment integrated into the printing press for washing cylinders and rollers such as ink rollers, blanket
cylinders, printing cylinders, plate cylinders, etc.
3.27
washing equipment for printing plates
machines for washing printing plates outside the printing press
EXAMPLE Screen washing equipment.
3.28
web-fed press
press in which a substrate passes through the printing couple(s) in a continuous form, as fed from a roll
3.29
web-type material
web of paper, board, foil or similar material that is to be handled or processed
3.30
Stand-alone Large-format digital printing machine (wide-format digital printing machine)
digital printing machine for the commercial production of large-format print products of different materials,
such as paper, plastic films/foils, textiles and flat structures in which an ink jet printing head arranged across
the transport of the product produces print on the printing substrate line by line. The substrate to be printed on
may be sheets or webs.
NOTE 1 to entry Generally these machines have an image area wider than 600 mm
4 Conformity with this part of ISO 12643
In order to claim conformity with this part of ISO 12643, all equipment manufactured as of 2014-01-01 shall be
in accordance with this third edition of ISO 12643-2 rather than ISO 12643-2:2010.
4 © ISO 2014 – All rights reserved
---------------------- Page: 12 ----------------------
oSIST prEN ISO 12643-2:2014
ISO/DIS 12643-2
NOTE Although this third version of ISO 12643-2 cancels and replaces the second edition (ISO 12643-2:2010), a
transition period might be necessary for equipment manufactured prior to 2014-01-01. To meet this need, it is noted that
both versions of ISO 12643-1 can be purchased from ISO and its National Bodies.
5 Equipment subject to requirements
5.1 General
This part of ISO 12643 is applicable to the equipment listed in 5.2 to 5.4. This equipment may be used in a
stand-alone configuration or in combination with other machines affected by an integrated control system. This
may include combinations of the machines noted below.
NOTE This part of ISO 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.