Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method (ISO 2106:2011)

This International Standard specifies a gravimetric method for determining the mass per unit area (surface density) of anodic oxidation coatings on aluminium and its alloys. The method is applicable to all oxidation coatings formed by anodizing aluminium and its alloys, either cast or wrought, and is suitable for most aluminium alloys, except those in which the copper content is greater than 6 %.

Anodisieren von Aluminium und Aluminiumlegierungen - Bestimmung der Masse je Flächeneinheit (flächenbezogene Masse) von anodisch erzeugten Oxidschichten - Gravimetrisches Verfahren (ISO 2106:2011)

Diese Internationale Norm legt ein gravimetrisches Verfahren zur Bestimmung der Masse je Flächeneinheit
(flächenbezogene Masse) anodisch erzeugter Oxidschichten auf Aluminium und Aluminiumlegierungen fest.
Das Verfahren ist auf alle Oxidschichten anwendbar, die durch anodische Oxidation von Aluminium, Aluminium-
Guss- und -Knetlegierungen erzeugt werden. Es ist für die meisten Aluminiumlegierungen geeignet, ausgenommen
für Legierungen mit einem Massenanteil von Kupfer über 6 %.
ANMERKUNG 1 Ein hoher Gehalt von Kupfer in der Legierung kann zu einer verstärkten Auflösung des Aluminium-
Grundmaterials führen.
ANMERKUNG 2 Wenn die Oxidschichtdicke mit ausreichender Genauigkeit bekannt ist (z. B. nach dem in ISO 2128
festgelegten Verfahren), kann aus der Masse je Flächeneinheit (flächenbezogene Masse) der Oxidschicht ihre scheinbare
Dichte errechnet werden. Sind die Bedingungen zur Aufbringung der Schicht und ihre Dichte bekannt, kann umgekehrt
aus der Masse je Flächeneinheit (flächenbezogene Masse) die mittlere Masse und ein ungefährer Wert für die
Schichtdicke errechnet werden (siehe Anmerkung in Abschnitt 6).

Anodisation de l'aluminium et de ses alliages - Détermination de la masse par unité de surface (masse surfacique) des couches anodiques - Méthode gravimétrique (ISO 2106:2011)

L'ISO 2106:2011 spécifie une méthode gravimétrique de détermination de la masse par unité de surface (masse surfacique) des couches anodiques sur l'aluminium et ses alliages.
Cette méthode est applicable à toutes les couches d'oxyde obtenues par anodisation sur l'aluminium et ses alliages, aussi bien sur pièces moulées que sur produits corroyés, et elle est valable pour la plupart des alliages d'aluminium, à l'exception de ceux dont la teneur en cuivre est supérieure à 6 %.

Anodizacija aluminija in aluminijevih zlitin - Ugotavljanje mase na enoto površine (površinska gostota) anodno oksidiranih prevlek - Gravimetrijska metoda (ISO 2106:2011)

Ta mednarodni standard določa gravimetrijsko metodo za ugotavljanje mase na površinsko enoto (površinske gostote) anodno oksidiranih prevlek na aluminiju in njegovih zlitinah. Metoda velja za vse oksidirane prevleke, ki nastanejo z anodizacijo aluminija in njegovih zlitin, ulitih ali gnetenih, in je primerna za večino aluminijevih zlitin, razen tistih, v katerih vsebnost bakra presega 6 %.

General Information

Status
Withdrawn
Public Enquiry End Date
14-Oct-2009
Publication Date
30-Nov-2011
Withdrawal Date
13-Feb-2020
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
13-Feb-2020
Due Date
07-Mar-2020
Completion Date
14-Feb-2020

Relations

Buy Standard

Standard
EN ISO 2106:2012
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2106:2012
01-januar-2012
1DGRPHãþD
SIST EN 12373-2:1999
Anodizacija aluminija in aluminijevih zlitin - Ugotavljanje mase na enoto površine
(površinska gostota) anodno oksidiranih prevlek - Gravimetrijska metoda (ISO
2106:2011)
Anodizing of aluminium and its alloys - Determination of mass per unit area (surface
density) of anodic oxidation coatings - Gravimetric method (ISO 2106:2011)
Anodisieren von Aluminium und Aluminiumlegierungen - Bestimmung der Masse je
Flächeneinheit (flächenbezogene Masse) von anodisch erzeugten Oxidschichten -
Gravimetrisches Verfahren (ISO 2106:2011)
Anodisation de l'aluminium et de ses alliages - Détermination de la masse par unité de
surface (masse surfacique) des couches anodiques - Méthode gravimétrique (ISO
2106:2011)
Ta slovenski standard je istoveten z: EN ISO 2106:2011
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 2106:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2106:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 2106:2012


EUROPEAN STANDARD
EN ISO 2106

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2011
ICS 25.220.20 Supersedes EN 12373-2:1998
English Version
Anodizing of aluminium and its alloys - Determination of mass
per unit area (surface density) of anodic oxidation coatings -
Gravimetric method (ISO 2106:2011)
Anodisation de l'aluminium et de ses alliages - Anodisieren von Aluminium und Aluminiumlegierungen -
Détermination de la masse par unité de surface (masse Bestimmung der Masse je Flächeneinheit
surfacique) des couches anodiques - Méthode (flächenbezogene Masse) von anodisch erzeugten
gravimétrique (ISO 2106:2011) Oxidschichten - Gravimetrisches Verfahren (ISO
2106:2011)
This European Standard was approved by CEN on 28 February 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2106:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2106:2012
EN ISO 2106:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 2106:2012
EN ISO 2106:2011 (E)
Foreword
The text of ISO 2106:2011 has been prepared by Technical Committee ISO/TC 79 "Light metals and their
alloys" of the International Organization for Standardization (ISO) and has been taken over as
EN ISO 2106:2011 by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2011, and conflicting national standards shall be
withdrawn at the latest by September 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12373-2:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2106:2011 has been approved by CEN as a EN ISO 2106:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 2106:2012

---------------------- Page: 6 ----------------------

SIST EN ISO 2106:2012

INTERNATIONAL ISO
STANDARD 2106
Third edition
2011-03-01

Anodizing of aluminium and its alloys —
Determination of mass per unit area
(surface density) of anodic oxidation
coatings — Gravimetric method
Anodisation de l'aluminium et de ses alliages — Détermination de la
masse par unité de surface (masse surfacique) des couches
anodiques — Méthode gravimétrique




Reference number
ISO 2106:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 2106:2012
ISO 2106:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2106:2012
ISO 2106:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.