SIST EN ISO 2411:2018
(Main)Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017)
Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017)
This document specifies a method of determining the coating adhesion strength of coated fabrics.
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Haftfestigkeit von Beschichtungen (ISO 2411:2017)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de l'adhérence du revêtement (ISO 2411:2017)
ISO 2411:2017 spécifie une méthode de détermination de la force d'adhérence du revêtement des supports textiles revêtus.
Gumirane ali plastificirane tekstilije - Ugotavljanje adhezije plasti (ISO 2411:2017)
Ta dokument določa metodo za ugotavljanje trdnosti adhezije plasti plastificiranih tekstilij.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN ISO 2411:2000
Gumirane ali plastificirane tekstilije - Ugotavljanje adhezije plasti (ISO 2411:2017)
Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Haftfestigkeit von
Beschichtungen (ISO 2411:2017)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de l'adhérence
du revêtement (ISO 2411:2017)
Ta slovenski standard je istoveten z: EN ISO 2411:2017
ICS:
59.080.40 3RYUãLQVNRSUHYOHþHQH Coated fabrics
WHNVWLOLMH
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 2411
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 59.080.40 Supersedes EN ISO 2411:2000
English Version
Rubber- or plastics-coated fabrics - Determination of
coating adhesion (ISO 2411:2017)
Supports textiles revêtus de caoutchouc ou de Mit Kautschuk oder Kunststoff beschichtete Textilien -
plastique - Détermination de l'adhérence du Bestimmung der Haftfestigkeit von Beschichtungen
revêtement (ISO 2411:2017) (ISO 2411:2017)
This European Standard was approved by CEN on 28 August 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2411:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 2411:2017) has been prepared by Technical Committee ISO/TC 45 “Rubber and
rubber products” in collaboration with Technical Committee CEN/TC 248 “Textiles and textile
products” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be
withdrawn at the latest by April 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2411:2000.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2411:2017 has been approved by CEN as EN ISO 2411:2017 without any modification.
INTERNATIONAL ISO
STANDARD 2411
Fourth edition
2017-09
Rubber- or plastics-coated fabrics —
Determination of coating adhesion
Supports textiles revêtus de caoutchouc ou de plastique —
Détermination de l'adhérence du revêtement
Reference number
ISO 2411:2017(E)
©
ISO 2017
ISO 2411:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 2411:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Atmosphere for conditioning and testing . 2
4.1 For conditioning . 2
4.2 For testing . 2
5 Time-interval between manufacture and testing. 2
6 Preparation of test specimens . 3
6.1 General . 3
6.2 Method of preparation 1 . 3
6.3 Method of preparation 2 . 3
6.4 Determination of wet coating adhesion . 4
6.4.1 End-use . 4
6.4.2 Preparation of test specimens . 4
6.4.3 Conducting the test . 4
7 Apparatus . 4
8 Procedure. 5
9 Calculation and expression of results . 5
9.1 General . 5
9.2 Determination of mid-point value . 5
9.3 Calculation of mean result . 5
9.4 Coating adhesion strength . 6
10 Test report . 6
Annex A (informative) Comments on interpretation of the autographic traces .11
ISO 2411:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses).
This fourth edition cancels and replaces the third edition (ISO 2411:2000), which has been technically
revised.
The changes compared to the previous edition are as follows:
— a warning statement has been added before the scope;
— in Clause 2, the publication year of ISO 2231 has been added;
— in 3.1, the definition of delamination has been modified;
— a new Clause 4, specifying the atmosphere for conditioning and testing, has been added;
— in Clause 6, the dimension of test specimen has been revised according to the addition of the test
specimen of 20 mm width in 6.2 and 6.3.4 ;
— in both 6.3.1 and 6.3.3, a welding process has been added;
— in 6.2.3 and 6.3.1, notes have been changed to body text;
— in Clause 7, Grade B and precision 1 have been changed to class B and class 1, respectively, according
to the updated references;
— in 9.2, N/10 mm and N/20 mm have been added;
— in Clause 10, items a), f), and l) have been added;
— in Figure 3, x-axis and y-axis names have been added;
— in Figure 4, figure subtitles have been added.
iv © ISO 2017 – All rights reserved
ISO 2411:2017(E)
Introduction
Knowledge of the strength of adhesion between the coating and the adjacent layer is important as an
inadequate adhesion strength can often result in failure of the product due to delamination.
INTERNATIONAL STANDARD ISO 2411:2017(E)
Rubber- or plastics-coated f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.