Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic pendulum method (ISO 4674-2:2021, Corrected version 2021-11)

This document specifies a method for the determination of tear resistance based on the action of an
active force applied to a notched test piece.
The test can be carried out on:
— test pieces that have been conditioned in a standard atmosphere; or
— test pieces that have undergone pre-treatment, e.g. water immersion.
The results obtained by this method cannot be compared with those obtained by methods involving
constant rate of tear.

Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Weiterreißfestigkeit - Teil 2: Verfahren mit ballistischem Pendel (ISO 4674-2:2021, korrigierte Fassung 2021-11)

Dieses Dokument legt ein Verfahren zur Bestimmung der Weiterreißfestigkeit, wenn auf einen Probekörper mit einer Einkerbung eine Weiterreißkraft wirkt, fest.
Die Prüfung gilt für:
- Probekörper, die in einem Normalklima konditioniert wurden; oder
- Probekörper, die vorbehandelt wurden, z. B. durch Eintauchen in Wasser.
Die Ergebnisse nach diesem Verfahren können nicht mit Ergebnissen verglichen werden, die bei Verfahren mit konstanter Reißgeschwindigkeit gewonnen wurden.
WARNUNG - Die in diesem Dokument beschriebene Prüfung sollte von erfahrenem Personal durchgeführt werden. In diesem Dokument werden nicht alle Sicherheitsprobleme behandelt, die bei Anwendung der Norm auftreten können. Es liegt in der Verantwortung des Anwenders, geeignete Sicherheits- und Gesundheitspraktiken festzulegen und Übereinstimmung mit Bedingungen nationaler Rechtsvorschriften sicherzustellen.

Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance au déchirement - Partie 2: Méthode au pendule balistique (ISO 4674-2:2021, Version corrigée 2021-11)

Le présent document spécifie une méthode pour la détermination de la résistance à la déchirure fondée sur l’action d’une force active appliquée à une éprouvette entaillée.
Les essais peuvent être pratiqués:
sur des éprouvettes conditionnées dans une atmosphère normale; ou
sur des éprouvettes ayant subi un traitement préalable, par exemple une immersion dans l’eau.
Les résultats obtenus par cette méthode ne peuvent être comparés à ceux obtenus par des méthodes mettant en jeu une vitesse constante de déchirement.

Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti trganju - 2. del: Metoda padajočega nihala (ISO 4674-2:2021, popravljena različica 2021-11)

General Information

Status
Published
Public Enquiry End Date
02-Aug-2020
Publication Date
15-Nov-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Oct-2021
Due Date
02-Jan-2022
Completion Date
16-Nov-2021

Relations

Buy Standard

Standard
EN ISO 4674-2:2021
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 4674-2:2021
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 4674-2:2020
German language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4674-2:2021
01-december-2021
Nadomešča:
SIST EN ISO 4674-2:1999
Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti trganju - 2. del:
Metoda padajočega nihala (ISO 4674-2:2021, popravljena različica 2021-11)
Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic
pendulum method (ISO 4674-2:2021, Corrected version 2021-11)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der
Weiterreißfestigkeit - Teil 2: Verfahren mit ballistischem Pendel (ISO 4674-2:2021,
korrigierte Fassung 2021-11)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance
au déchirement - Partie 2: Méthode au pendule balistique (ISO 4674-2:2021, Version
corrigée 2021-11)
Ta slovenski standard je istoveten z: EN ISO 4674-2:2021
ICS:
59.080.40 Površinsko prevlečene Coated fabrics
tekstilije
SIST EN ISO 4674-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 4674-2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 4674-2:2021


EN ISO 4674-2
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 59.080.40 Supersedes EN ISO 4674-2:1998
English Version

Rubber- or plastics-coated fabrics - Determination of tear
resistance - Part 2: Ballistic pendulum method (ISO 4674-
2:2021, Corrected version 2021-11)
Supports textiles revêtus de caoutchouc ou de Mit Kautschuk oder Kunststoff beschichtete Textilien -
plastique - Détermination de la résistance au Bestimmung der Weiterreißfestigkeit - Teil 2:
déchirement - Partie 2: Méthode au pendule balistique Verfahren mit ballistischem Pendel (ISO 4674-2:2021,
(ISO 4674-2:2021, Version corrigée 2021-11) korrigierte Fassung 2021-11)
This European Standard was approved by CEN on 31 August 2021.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 8 December 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N

EUROPÄISCHES KOMITEE FÜR NORMUN G

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4674-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 4674-2:2021
EN ISO 4674-2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 4674-2:2021
EN ISO 4674-2:2021 (E)
European foreword
This document (EN ISO 4674-2:2021) has been prepared by Technical Committee ISO/TC 45 "Rubber
and rubber products" in collaboration with Technical Committee CEN/TC 248 “Textiles and textile
products” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4674-2:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 4674-2:2021, Corrected version 2021-11 has been approved by CEN as EN ISO 4674-
2:2021 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 4674-2:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 4674-2:2021
INTERNATIONAL ISO
STANDARD 4674-2
Second edition
2021-10
Corrected version
2021-11
Rubber- or plastics-coated fabrics —
Determination of tear resistance —
Part 2:
Ballistic pendulum method
Supports textiles revêtus de caoutchouc ou de plastique —
Détermination de la résistance au déchirement —
Partie 2: Méthode au pendule balistique
Reference number
ISO 4674-2:2021(E)
© ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and reagents .2
6 Sampling and preparation of test pieces . 2
6.1 Sampling . 2
6.2 Test pieces . 3
6.2.1 Shape and dimensions . 3
6.2.2 Number of test pieces . 5
6.3 Pre-treatment for wet test . 5
7 Time-interval between manufacture and testing . 5
8 Atmosphere for conditioning and testing . 5
8.1 For conditioning . 5
8.2 For testing . 5
9 Procedure .5
10 Expression of results . 6
11 Test report . 6
Annex A (normative) Adjustment and calibration . 7
Bibliography . 8
iii
© ISO 2021 – All rights reserved

---------------------- Page: 9 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses), in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 248, Textiles and textile products, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 4674-2:1998), which has been technically
revised. The main changes compared with the previous edition are as follows:
— in Clause 5, the title has been changed to “Apparatus and reagents” and 5.3, 5.4, and 5.5 have been
added;
— in Clause 6, the title has been changed to “Sampling and preparation of test pieces” and Clause 5 has
been integrated;
— in Clause 7, the test duration has been specified;
— in Clause 8, the title has been changed to “Atmosphere for conditioning and testing” and 8.2 has
been added;
— in Clause 9, the wet test has been specified.
This corrected version of ISO 4674-2:2021 incorporates the following corrections:
— "Dimensions in millimetres" has been added to Figure 1.
A list of all parts in the ISO 4674 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Introduction
Tearing is amongst the more usual ways of destruction for many thin materials such as paper, coated or
unco
...

SLOVENSKI STANDARD
SIST EN ISO 4674-2:2021
01-december-2021
Nadomešča:
SIST EN ISO 4674-2:1999
Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti trganju - 2. del:
Metoda padajočega nihala (ISO 4674-2:2021)
Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic
pendulum method (ISO 4674-2:2021)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der
Weiterreißfestigkeit - Teil 2: Verfahren mit ballistischem Pendel (ISO 4674-2:2021)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance
au déchirement - Partie 2: Méthode au pendule balistique (ISO 4674-2:2021)
Ta slovenski standard je istoveten z: EN ISO 4674-2:2021
ICS:
59.080.40 Površinsko prevlečene Coated fabrics
tekstilije
SIST EN ISO 4674-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 4674-2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 4674-2:2021


EN ISO 4674-2
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 59.080.40 Supersedes EN ISO 4674-2:1998
English Version

Rubber- or plastics-coated fabrics - Determination of tear
resistance - Part 2: Ballistic pendulum method (ISO 4674-
2:2021)
Supports textiles revêtus de caoutchouc ou de Mit Kautschuk oder Kunststoff beschichtete Textilien -
plastique - Détermination de la résistance au Bestimmung der Weiterreißfestigkeit - Teil 2:
déchirement - Partie 2: Méthode au pendule balistique Verfahren mit ballistischem Pendel (ISO 4674-2:2021)
(ISO 4674-2:2021)
This European Standard was approved by CEN on 31 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4674-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 4674-2:2021
EN ISO 4674-2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 4674-2:2021
EN ISO 4674-2:2021 (E)
European foreword
This document (EN ISO 4674-2:2021) has been prepared by Technical Committee ISO/TC 45 "Rubber
and rubber products" in collaboration with Technical Committee CEN/TC 248 “Textiles and textile
products” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4674-2:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 4674-2:2021 has been approved by CEN as EN ISO 4674-2:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 4674-2:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 4674-2:2021
INTERNATIONAL ISO
STANDARD 4674-2
Second edition
2021-10
Rubber- or plastics-coated fabrics —
Determination of tear resistance —
Part 2:
Ballistic pendulum method
Supports textiles revêtus de caoutchouc ou de plastique —
Détermination de la résistance au déchirement —
Partie 2: Méthode au pendule balistique
Reference number
ISO 4674-2:2021(E)
© ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and reagents .2
6 Sampling and preparation of test pieces . 2
6.1 Sampling . 2
6.2 Test pieces . 3
6.2.1 Shape and dimensions . 3
6.2.2 Number of test pieces . 5
6.3 Pre-treatment for wet test . 5
7 Time-interval between manufacture and testing . 5
8 Atmosphere for conditioning and testing . 5
8.1 For conditioning . 5
8.2 For testing . 5
9 Procedure .5
10 Expression of results . 6
11 Test report . 6
Annex A (normative) Adjustment and calibration . 7
Bibliography . 8
iii
© ISO 2021 – All rights reserved

---------------------- Page: 9 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses), in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 248, Textiles and textile products, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 4674-2:1998), which has been technically
revised. The main changes compared with the previous edition are as follows:
— in Clause 5, the title has been changed to “Apparatus and reagents” and 5.3, 5.4, and 5.5 have been
added;
— in Clause 6, the title has been changed to “Sampling and preparation of test pieces” and Clause 5 has
been integrated;
— in Clause 7, the test duration has been specified;
— in Clause 8, the title has been changed to “Atmosphere for conditioning and testing” and 8.2 has
been added;
— in Clause 9, the wet test has been specified.
A list of all parts in the ISO 4674 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 4674-2:2021
ISO 4674-2:2021(E)
Introduction
Tearing is amongst the more usual ways of destruction for many thin materials such as paper, coated or
uncoated textiles, plastics films and leather. Knowledge of the resistance of these materials to this type
of behaviour is therefore very important.
In practice, tearing can result from very different circumstances; hence the large number of test
...

SLOVENSKI STANDARD
oSIST prEN ISO 4674-2:2020
01-julij-2020
Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti trganju - 2. del:
Metoda padajočega nihala (ISO/DIS 4674-2:2020)
Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic
pendulum method (ISO/DIS 4674-2:2020)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der
Weiterreißfestigkeit - Teil 2: Verfahren mit ballistischem Pendel (ISO/DIS 4674-2:2020)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance
au déchirement - Partie 2: Méthode au pendule balistique (ISO/DIS 4674-2:2020)
Ta slovenski standard je istoveten z: prEN ISO 4674-2
ICS:
59.080.40 Površinsko prevlečene Coated fabrics
tekstilije
oSIST prEN ISO 4674-2:2020 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 4674-2:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 4674-2:2020


ENTWURF
EUROPÄISCHE NORM
prEN ISO 4674-2
EUROPEAN STANDARD

NORME EUROPÉENNE

Mai 2020
ICS 59.080.40 Vorgesehen als Ersatz für EN ISO 4674-2:1998
Deutsche Fassung

Mit Kautschuk oder Kunststoff beschichtete Textilien -
Bestimmung der Weiterreißfestigkeit - Teil 2: Verfahren mit
ballistischem Pendel (ISO/DIS 4674-2:2020)
Rubber- or plastics-coated fabrics - Determination of Supports textiles revêtus de caoutchouc ou de plastique
tear resistance - Part 2: Ballistic pendulum method - Détermination de la résistance au déchirement - Partie
(ISO/DIS 4674-2:2020) 2: Méthode au pendule balistique (ISO/DIS 4674-
2:2020)
Dieser Europäische Norm-Entwurf wird den CEN-Mitgliedern zur parallelen Umfrage vorgelegt. Er wurde vom Technischen
Komitee CEN/TC 248 erstellt.

Wenn aus diesem Norm-Entwurf eine Europäische Norm wird, sind die CEN-Mitglieder gehalten, die CEN-Geschäftsordnung zu
erfüllen, in der die Bedingungen festgelegt sind, unter denen dieser Europäischen Norm ohne jede Änderung der Status einer
nationalen Norm zu geben ist.

Dieser Europäische Norm-Entwurf wurde von CEN in drei offiziellen Fassungen (Deutsch, Englisch, Französisch) erstellt. Eine
Fassung in einer anderen Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine
Landessprache gemacht und dem CEN-CENELEC-Management-Zentrum mitgeteilt worden ist, hat den gleichen Status wie die
offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, Estland, Finnland,
Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta, den Niederlanden, Norwegen,
Österreich, Polen, Portugal, der Republik Nordmazedonien, Rumänien, Schweden, der Schweiz, Serbien, der Slowakei, Slowenien,
Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und Zypern.

Die Empfänger dieses Norm-Entwurfs werden gebeten, mit ihren Kommentaren jegliche relevante Patentrechte, die sie kennen,
mitzuteilen und unterstützende Dokumentationen zur Verfügung zu stellen.

Warnvermerk : Dieses Schriftstück hat noch nicht den Status einer Europäischen Norm. Es wird zur Prüfung und Stellungnahme
vorgelegt. Es kann sich noch ohne Ankündigung ändern und darf nicht als Europäischen Norm in Bezug genommen werden.


EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Rue de la Science 23, B-1040 Brüssel
© 2020 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. prEN ISO 4674-2:2020 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN
vorbehalten.

---------------------- Page: 3 ----------------------
oSIST prEN ISO 4674-2:2020
prEN ISO 4674-2:2020 (D)
Inhalt
Seite
Europäisches Vorwort . 3
Vorwort . 4
Einleitung . 5
1 Anwendungsbereich . 6
2 Normative Verweisungen . 6
3 Begriffe . 6
4 Kurzbeschreibung . 6
5 Geräte und Reagenzien . 7
6 Probenahme und Probenvorbereitung . 8
6.1 Probenahme . 8
6.2 Probekörper . 8
6.2.1 Form und Maße . 8
6.2.2 Anzahl . 10
6.3 Vorbehandlung für Nassprüfung . 10
7 Zeitintervall zwischen Herstellung und Prüfung . 10
8 Klima zur Konditionierung und Prüfung . 10
8.1 Zur Konditionierung . 10
8.2 Zur Prüfung . 10
9 Durchführung . 10
10 Auswertung . 11
11 Prüfbericht . 12
Anhang A (informativ) Einstellung und Kalibrierung . 13
A.1 Einstellung des Prüfgerätes . 13
A.1.1 Allgemeines . 13
A.1.2 Nivellierung . 13
A.1.3 Schneidklinge . 13
A.1.4 Lagerreibung . 13
A.1.5 Nullstellung . 13
A.2 Kalibrierung . 13
Literaturhinweise . 14

2

---------------------- Page: 4 ----------------------
oSIST prEN ISO 4674-2:2020
prEN ISO 4674-2:2020 (D)
Europäisches Vorwort
Dieses Dokument (prEN ISO 4674-2:2020) wurde vom Technischen Komitee ISO/TC 45 „Rubber and rubber
products“ in Zusammenarbeit mit dem Technischen Komitee CEN/TC 248 „Textilien und textile Erzeugnisse“
erarbeitet, dessen Sekretariat von BSI gehalten wird.
Dieses Dokument ist derzeit zur parallelen Umfrage vorgelegt.
Dieses Dokument wird EN ISO 4674-2:1998 ersetzen.
Anerkennungsnotiz
Der Text von ISO/DIS 4674-2:2020 wurde von CEN als prEN ISO 4674-2:2020 ohne irgendeine Abänderung
genehmigt.
3

---------------------- Page: 5 ----------------------
oSIST prEN ISO 4674-2:2020
prEN ISO 4674-2:2020 (D)
Vorwort
ISO (die Internationale Organisation für Normung) ist eine weltweite Vereinigung nationaler
Normungsinstitute (ISO-Mitgliedsorganisationen). Die Erstellung von Internationalen Normen wird
üblicherweise von Technischen Komitees von ISO durchgeführt. Jede Mitgliedsorganisation, die Interesse an
einem Thema hat, für welches ein Technisches Komitee gegründet wurde, hat das Recht, in diesem Komitee
vertreten zu sein. Internationale staatliche und nichtstaatliche Organisationen, die in engem Kontakt mit ISO
stehen, nehmen ebenfalls an der Arbeit teil. ISO arbeitet bei allen elektrotechnischen Normungsthemen eng
mit der Internationalen Elektrotechnischen Kommission (IEC) zusammen.
Die Verfahren, die bei der Entwicklung dieses Dokuments angewendet wurden und die für die weitere Pflege
vorgesehen sind, werden in den ISO/IEC-Direktiven, Teil 1 beschrieben. Es sollten insbesondere die
unterschiedlichen Annahmekriterien für die verschiedenen ISO-Dokumentenarten beachtet werden. Dieses
Dokument wurde in Übereinstimmung mit den Gestaltungsregeln der ISO/IEC-Direktiven, Teil 2 erarbeitet
(siehe www.iso.org/directives).
Es wird auf die Möglichkeit hingewiesen, dass einige Elemente dieses Dokuments Patentrechte berühren
können. ISO ist nicht dafür verantwortlich, einige oder alle diesbezüglichen Patentrechte zu identifizieren.
Details zu allen während der Entwicklung des Dokuments identifizierten Patentrechten finden sich in der
Einleitung und/oder in der ISO-Liste der erhaltenen Patenterklärungen (siehe www.iso.org/patents).
Jeder in diesem Dokument verwendete Handelsname dient nur zur Unterrichtung der Anwender und
bedeutet keine Anerkennung.
Für eine Erläuterung des freiwilligen Charakters von Normen, der Bedeutung ISO-spezifischer Begriffe und
Ausdrücke in Bezug auf Konformitätsbewertungen sowie Informationen darüber, wie ISO die Grundsätze der
Welthandelsorganisation (WTO, en: World Trade Organization) hinsichtlich technischer Handelshemmnisse
(TBT, en: Technical Barriers to Trade) berücksichtigt, siehe www.iso.org/iso/foreword.html.
Dieses Dokument wurde vom Technischen Komitee ISO/TC 45, Rubber & Rubber Products,
Unterkomitee SC 04, Products other than hoses ausgearbeitet
Diese zweite Ausgabe ersetzt die erste Ausgabe (ISO 4674-2:1998), die technisch überarbeitet wurde.
Die wesentlichen Änderungen im Vergleich zur Vorgängerausgabe sind folgende:
— Abschnitt 5: Der Titel wurde geändert zu „Geräte und Reagenzien“ und 5.3, 5.4 und 5.5 wurden
hinzugefügt;
— Abschnitt 6: Der Titel wurde geändert zu „Probenahme und Probenvorbereitung“ und Abschnitt 5
wurde in Abschnitt 6 (ISO 4674-2:1998) integriert;
— Abschnitt 7: Die Zeit für die Prüfung wurde spezifiziert;
— Abschnitt 8: Der Titel wurde geändert zu „Klima zur Konditionierung und Prüfung“ und 8.2 wurde
hinzugefügt;
— Abschnitt 9: Die Nassprüfung wurde spezifiziert.
Eine Auflistung aller Teile der Normenreihe ISO 4674 ist auf der ISO-Internetseite abrufbar.
Rückmeldungen oder Fragen zu diesem Dokument sollten an das jeweilige nationale Normungsinstitut des
Anwenders gerichtet werden. Eine vollständige Auflistung dieser Institute ist unter
www.iso.org/members.html zu finden.
4

---------------------- Page: 6 ----------------------
oSIST prEN ISO 4674-2:2020
prEN ISO 4674-2:2020 (D)
Einleitung
Viele dünne Materialien, z. B. Papier, beschichtete oder unbeschichtete Textilien, Kunststofffolien und Leder
werden häufig dadurch zerstört, dass sie zerreißen. Kenntnisse über die Reißfestigkeit sind folglich sehr
wertvoll.
In der Praxis können dünne Materialien unter sehr unterschiedlichen Umständen zerreißen; deswegen
wurde eine große Anzahl von Prüfverfahren entwickelt, mit denen das Werkstoffverhalten unter
verschiedenen Bedingungen vorherzubestimmen ist.
Diese Internationale Norm beschreibt das Weiterreißen, d. h. die von einem Einschnitt ausgehende
Ausbreitung eines Risses. Die Norm besteht aus den folgenden zwei Teilen:
— Teil 1: Verfahren mit konstanter Geschwindigkeit;
— Teil 2: Verfahren mit ballistischem Pendel.
Im ersten Teil werden zwei Verfahren beschrieben, bei denen eine Zugprüfmaschine mit konstanter
Verformungsgeschwindigkeit verwendet wird. Der zweite Teil legt ein dynamisches Verfahren fest, das die
kinetische Energie eines fallenden Pendels ausnutzt.
Andere Verfahren werden daraufhin überprüft, ob sie möglicherweise weitere Teile dieser Norm werden
können, z. B. die „Berstprüfung bei Verwindung“.
5

---------------------- Page: 7 ----------------------
oSIST prEN ISO 4674-2:2020
prEN ISO 4674-2:2020 (D)
WARNUNG — Die in diesem Dokument beschriebene Prüfung sollte von erfahrenem Personal
durchgeführt werden. In diesem Dokument werden nicht alle Sicherheitsprobleme behandelt, die bei
Anwendung der Norm auftreten können. Es liegt in der Verantwortung des Anwenders, geeignete
Sicherheits- und Gesundheitspraktiken festzulegen und Übereinstimmung mit Bedingungen
nationaler Rechtsvorschriften sicherzustellen.
1 Anwendungsbereich
Dieses Dokument legt ein Verfahren zur Bestimmung der Weiterreißfestigkeit, wenn auf einen Probekörper
mit einer Einkerbung eine Weiterreißkraft wirkt, fest.
Die Prüfung gilt fü
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.