SIST-TS CEN ISO/TS 21003-7:2019
(Main)Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
This document gives requirements and guidance for the assessment of conformity of compounds,
products, and assemblies in accordance with the applicable part(s) of ISO 21003 intended to be included
in the manufacturer’s quality plan as part of the quality management system and for the establishment
of certification procedures.
In conjunction with the other parts of ISO 21003 (see Foreword), this document is applicable to
multilayer piping systems intended to be used for hot and cold water installations within buildings for
the conveyance of water, whether or not intended for human consumption (domestic systems) and for
heating systems, under design pressures and temperatures appropriate to the class of application (see
ISO 21003-1:2008, Table 1).
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/TS 21003-7:2019)
Dieses Dokument enthält Anforderungen und Empfehlungen für die Beurteilung der Konformität von Formmassen, Produkten und Bauteilkombinationen, die, in Übereinstimmung mit den/dem entsprechenden Teil(en) von ISO 21003, als Teil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
Zusammen mit den übrigen Teilen von ISO 21003 (siehe Vorwort) gilt dieses Dokument für Mehrschichtverbund-Rohrleitungssysteme, die in der Warm und Kaltwasserinstallation innerhalb von Gebäuden für die Durchleitung von Trink oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden Systembetriebsdrucks und der für die jeweilige Anwendungs¬klasse geltenden Temperaturen (siehe ISO 21003 1:2008, Tabelle 1) eingesetzt werden.
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à l'intérieur des bâtiments - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS 21003-7:2019)
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 7. del: Navodilo za ugotavljanje skladnosti (ISO/TS 21003-7:2019)
Ta dokument vsebuje priporočila in navodila za ugotavljanje skladnosti zmesi, izdelkov in sestavov z ustreznimi deli standarda ISO 21003, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja.
Ta dokument se v povezavi z drugimi deli standarda ISO 21003 (glej predgovor) uporablja za večslojne cevne sisteme v napeljavah z vročo in hladno vodo za prenos pitne in nepitne vode v stavbah (gospodinjski sistemi) ter za sisteme ogrevanja glede na predvidene tlake in temperature, ki ustrezajo razredu uporabe (glej standard ISO 21003-1:2008, preglednica 1).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 21003-7:2019
01-september-2019
Nadomešča:
SIST-TS CEN ISO/TS 21003-7:2009
SIST-TS CEN ISO/TS 21003-7:2009/A1:2010
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 7. del:
Navodilo za ugotavljanje skladnosti (ISO/TS 21003-7:2019)
Multilayer piping systems for hot and cold water installations inside buildings - Part 7:
Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation
innerhalb von Gebäuden - Teil 7: Empfehlungen für die Beurteilung der Konformität
(ISO/TS 21003-7:2019)
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à
l'intérieur des bâtiments - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS
21003-7:2019)
Ta slovenski standard je istoveten z: CEN ISO/TS 21003-7:2019
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST-TS CEN ISO/TS 21003-7:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
---------------------- Page: 2 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
CEN ISO/TS 21003-7
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
May 2019
TECHNISCHE SPEZIFIKATION
ICS 23.040.20; 91.140.60 Supersedes CEN ISO/TS 21003-7:2008
English Version
Multilayer piping systems for hot and cold water
installations inside buildings - Part 7: Guidance for the
assessment of conformity (ISO/TS 21003-7:2019)
Systèmes de canalisations multicouches pour Mehrschichtverbund-Rohrleitungssysteme für die
installations d'eau chaude et froide à l'intérieur des Warm- und Kaltwasserinstallation innerhalb von
bâtiments - Partie 7: Guide pour l'évaluation de la Gebäuden - Teil 7: Empfehlungen für die Beurteilung
conformité (ISO/TS 21003-7:2019) der Konformität (ISO/TS 21003-7:2019)
This Technical Specification (CEN/TS) was approved by CEN on 28 March 2019 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 21003-7:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
CEN ISO/TS 21003-7:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
CEN ISO/TS 21003-7:2019 (E)
European foreword
This document (CEN ISO/TS 21003-7:2019) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 21003-7:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO/TS 21003-7:2019 has been approved by CEN as CEN ISO/TS 21003-7:2019 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
---------------------- Page: 6 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
TECHNICAL ISO/TS
SPECIFICATION 21003-7
Second edition
2019-04
Multilayer piping systems for hot
and cold water installations inside
buildings —
Part 7:
Guidance for the assessment of
conformity
Systèmes de canalisations multicouches pour installations d'eau
chaude et froide à l'intérieur des bâtiments —
Partie 7: Guide pour l'évaluation de la conformité
Reference number
ISO/TS 21003-7:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms and symbols . 4
4.1 Abbreviated terms . 4
4.2 Symbols . 5
5 General . 5
6 Testing and inspection . 5
6.1 Grouping . 5
6.1.1 General. 5
6.1.2 Pressure groups . 5
6.1.3 Size groups . 6
6.1.4 Fitting groups . 6
6.2 Type testing . 6
6.3 Batch release test .15
6.4 Process verification tests (PVTs) .16
6.5 Audit tests (AT) .17
6.6 Indirect testing (IT).17
6.7 Test records.18
Annex A (informative) Interchangeability of different material grades — Testing of
alternative material grades for a layer in a multilayer M-pipe (second sourcing) .19
Bibliography .31
© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical
Committee TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2,
Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO/TS 21003-7:2008), which has been
technically revised. It also incorporates the Amendment ISO/TS 21003-7:2008/Amd1: 2010.
The major technical changes are:
— New definition of the terms “material”, “material grade” and “compound”;
— Revision of 6.2 “type testing”;
— Addition of Annex A "Interchangeability of different material grades — Testing of an alternative
material grades for a layer in a Multilayer M-Pipe (second sourcing)”.
A list of all parts in the ISO 21003 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
Introduction
This document can be used to support elaboration of national third party certification procedures for
products conforming to the applicable part(s) of ISO 21003.
This document is a part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
At the date of publication of this document, System Standards for piping systems of other plastics
materials used for the same application are the following:
— ISO 15874, Plastics piping systems for hot and cold water installations — Polypropylene (PP)
— ISO 15875, Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X)
— ISO 15876, Plastics piping systems for hot and cold water installations — Polybutene (PB)
— ISO 15877, Plastics piping systems for hot and cold water installations — Chlorinated poly (vinyl
chloride) (PVC-C)
— ISO 22391, Plastics piping systems for hot and cold water installations — Polyethylene of raised
temperature resistance (PE-RT)
They are supported by separate standards on test methods to which references are made throughout
the System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
Figures 1 and 2 are intended to provide general information on the concept of testing and organisation
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type testing
(TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document details
the applicable characteristics to be assessed as well as the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials, compounds, pipes, fittings, valves,
joints or assemblies by product manufacturers is given in Figure 1
Figure 1 — Typical scheme for the assessment of conformity by a product manufacturer
A typical scheme for the assessment of conformity of compounds, pipes, fittings, joints or assemblies by
manufacturers, including certification, is given in Figure 2.
© ISO 2019 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
Figure 2 — Typical scheme for the assessment of conformity by product a manufacturer,
including certification.
vi © ISO 2019 – All rights reserved
---------------------- Page: 12 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
TECHNICAL SPECIFICATION ISO/TS 21003-7:2019(E)
Multilayer piping systems for hot and cold water
installations inside buildings —
Part 7:
Guidance for the assessment of conformity
1 Scope
This document gives requirements and guidance for the assessment of conformity of compounds,
products, and assemblies in accordance with the applicable part(s) of ISO 21003 intended to be included
in the manufacturer’s quality plan as part of the quality management system and for the establishment
of certification procedures.
In conjunction with the other parts of ISO 21003 (see Foreword), this document is applicable to
multilayer piping systems intended to be used for hot and cold water installations within buildings for
the conveyance of water, whether or not intended for human consumption (domestic systems) and for
heating systems, under design pressures and temperatures appropriate to the class of application (see
ISO 21003-1:2008, Table 1).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 17456, Plastics piping systems — Multilayer pipes — Determination of long-term strength
ISO 21003-1, Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
ISO 21003-2, Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
ISO 21003-3, Multilayer piping systems for hot and cold water installations inside buildings — Part 3:
Fittings
ISO 21003-5, Multilayer piping systems for hot and cold water installations inside buildings — Part 5:
Fitness for purpose of the system
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 21003-1, ISO 21003-3 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at http: //www .iso .org/obp
© ISO 2019 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with ISO/IEC 17065.
3.2
inspection body
body that performs inspection
Note 1 to entry: An inspection body can be an organization, or part of an organization.
[3]
Note 2 to entry: An inspection body is preferably compliant with ISO/IEC 17020 .
[3]
[SOURCE: ISO/IEC 17020:2012 , 3.5]
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: A testing laboratory is preferably compliant with ISO/IEC 17025.
3.4
quality management system
part of a management system with regard to quality
[1]
Note 1 to entry: Requirements for quality management systems are given in ISO 9001 .
[6]
[SOURCE: ISO 9000:2015 , 3.5.4, modified — Note 1 to entry has been added]
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the compound, component, product, joint or assembly is capable of
conforming to the requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the compound or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of material compound, components or
products, which has to be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the product manufacturer on compounds, components, products or
joints at specific intervals to confirm that the process continues to be capable of producing components
and products which conform to the requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of materials, compound, components or products
and are carried out as a measure of process control
2 © ISO 2019 – All rights reserved
---------------------- Page: 14 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
3.9
audit test
AT
test performed by a test laboratory on behalf of an inspection body or certification body to confirm
that the material, compound, components, product, joint or assembly continues to conform to the
requirements given in the relevant standard and to provide information to assess the effectiveness of
the quality management system
3.10
indirect test
IT
test performed by or on behalf of the manufacturer, different from that specified test for that particular
characteristic, having previously verified its correlation with the specified test
3.11
witness test
WT
test accepted by an inspection or a certification body for type testing and/or audit testing, which is
carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or
certification body, qualified in testing
3.12
material
composition grouped by families, expressed by generic names used in material standards, e.g. PP-H, PB-
R, PE-RT Type II, PE-Xa, aluminium alloy type 8006
3.13
material grade
material with a defined specification from a material manufacturer
3.14
alternative material grade
material grade available for the production of a multilayer pipe, but different from the one used in the
type test (second sourcing)
Note 1 to entry: The pipe manufacturer might have alternative material grades for the inner layer, inner adhesive
layer, metal layer, outer adhesive layer and/or outer layer of the multilayer pipe.
3.15
compound
clearly defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments, stabilizers
and others, at a dosage level necessary for the processing and the intended use of the final product
3.16
batch of material grade
clearly identified quantity of a given homogeneous materials or compound manufactured under
uniform conditions and defined and identified by the materials or compound manufacturer
3.17
product
pipe, fitting, or valve of a clearly identified type intended to be a part of a piping system, which the
manufacturer puts on the market
3.18
product batch
clearly identified collection of units or products, manufactured consecutively or continuously under the
same conditions, using the same compounds conforming to the same specifications
Note 1 to entry: The production batch is defined and identified by the product manufacturer.
© ISO 2019 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
3.19
lot
clearly identifiable sub-division of a batch for inspection purposes
3.20
sample
one or more units or products drawn from the same production batch or lot, selected at random without
regard to their quality
Note 1 to entry: The number of products in the sample is the sample size.
3.21
group
collection of similar components from which samples are selected for testing purposes
3.22
component
product manufactured out of a specific material or compound, brought to the market as part of another
product or as a spare part
Note 1 to entry: For drinking water application, components may be considered as products and be individually
approved (e.g. o-ring, gasket) or they are tested as an integral part of a product (e.g. in a valve).
3.23
joint
connection between two or more products
3.24
assembly/assembled product
product consisting of two or more parts
3.25
sampling plan
specific plan, which defines the test and the number of units or products or assemblies to be inspected
3.26
product type
generic description of a product
EXAMPLE A pipe or fitting or valve or their main parts, of the same design, from a particular compound.
3.27
cavity
space within a mould to be filled to form the moulded product
EXAMPLE That part of an injection mould which gives the form to the injection-moulded product.
4 Abbreviated terms and symbols
4.1 Abbreviated terms
To avoid misunderstanding, the abbreviated terms in this clause are defined as being the same in each
language. For the same reason, the terms are given in the three languages, English, French and German.
EN FR DE
AT audit test essai d’audit Überwachungsprüfung
essai de libération de campagne de fab-
BRT batch release test Freigabeprüfung einer Charge
rication
IT indirect test essai indirect indirekte Prüfung
4 © ISO 2019 – All rights reserved
---------------------- Page: 16 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
EN FR DE
essai de vérification du procédé de fab-
PVT process verification test Prozessüberprüfung
rication
TT type test essai de type Typprüfung
WT witness testing essai témoin Prüfung unter Aufsicht
4.2 Symbols
I Material grade used in the inner layer of the initial type-tested M-pipe
0
Ai Material grade used in the inner adhesive layer of the initial type-tested M-pipe
0
M Material grade used in the metal layer of the initial type-tested M-pipe
0
Ao Material grade used in the outer adhesive layer of the initial type-tested M-pipe
0
O Material grade used in the outer layer of the initial type-tested M-pipe
0
I Alternative material grade to be introduced in the inner layer
1
Ai Alternative material grade to be introduced in the inner adhesive layer
1
M Alternative material grade to be introduced in the metal layer
1
Ao Alternative material grade to be introduced in the outer adhesive layer
1
O Alternative material grade to be introduced in the outer layer
1
5 General
Compounds, products and assemblies shall conform to the requirements given of ISO 21003 (all parts).
Products and assemblies shall be produced by the manufacturer under a quality management system,
which includes a quality plan.
6 Testing and inspection
6.1 Grouping
6.1.1 General
For the purposes of this document, the groups specified in 6.1.2 to 6.1.4 apply.
6.1.2 Pressure groups
Two pressure groups are defined, as given in Table 1.
Table 1 — Pressure groups
Pressure group Operating pressure, p
op
bar
1 4; 6
2 8; 10
© ISO 2019 – All rights reserved 5
---------------------- Page: 17 ----------------------
SIST-TS CEN ISO/TS 21003-7:2019
ISO/TS 21003-7:2019(E)
6.1.3 Size groups
Three size groups are defined for pipes and fittings, as given in Table 2.
Table 2 — Size groups
Size group Nominal diameter, d
n
mm
1 10 ≤ d ≤ 26
n
2 26 < d ≤ 63
n
3 d > 63
n
6.1.4 Fitting groups
Two groups of fittings having a similar design are defined, as given in Table 3.
Table 3 — Fitting groups
Fitting group Type of fitting
1 Elbows, tees, reducers, couplers, end caps
Unions, flange adaptors, transition fitting, adaptor pieces
2
and/or their plastics parts and others
6.2 Type testing
Relevant TTs shall be carried out on new systems and whenever there is a change in design, compound,
production site or production method, other than routine in-process adjustments, and/or whenever
there is an extension of the product range.
Type tests shall demonstrate that the products conform to all requirements for the characteristics
given in Table 6 to Table 10, as applicable.
Conditions considered as leading to a change of compound (M) of M-pipes and P-pipes are given in
Tables 4 and 5. Tables 4 and 5 offer a wide range of changes.
NOTE 1
— Example 1: A change of the inner layer material from PE-Xa to PERT Type II
— Example 2: A change of the metal layer material from an aluminium alloy type 8006 to a different aluminium
alloy type or even to a steel alloy.
— Example 3: A change of a material grade used for the inner layer to another material grade from another raw
material supplier.
The relevant characteristics to be tested in case of change of compound of M-pipes and P-pipes are
given in Tables 6, 7 and 10 i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.