CEN ISO/TS 21003-7:2019
(Main)Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 21003 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 21003 (see Foreword), this document is applicable to multilayer piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 21003-1:2008, Table 1).
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/TS 21003-7:2019)
Dieses Dokument enthält Anforderungen und Empfehlungen für die Beurteilung der Konformität von Formmassen, Produkten und Bauteilkombinationen, die, in Übereinstimmung mit den/dem entsprechenden Teil(en) von ISO 21003, als Teil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
Zusammen mit den übrigen Teilen von ISO 21003 (siehe Vorwort) gilt dieses Dokument für Mehrschichtverbund-Rohrleitungssysteme, die in der Warm und Kaltwasserinstallation innerhalb von Gebäuden für die Durchleitung von Trink oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden Systembetriebsdrucks und der für die jeweilige Anwendungs¬klasse geltenden Temperaturen (siehe ISO 21003 1:2008, Tabelle 1) eingesetzt werden.
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à l'intérieur des bâtiments - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS 21003-7:2019)
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 7. del: Navodilo za ugotavljanje skladnosti (ISO/TS 21003-7:2019)
Ta dokument vsebuje priporočila in navodila za ugotavljanje skladnosti zmesi, izdelkov in sestavov z ustreznimi deli standarda ISO 21003, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja.
Ta dokument se v povezavi z drugimi deli standarda ISO 21003 (glej predgovor) uporablja za večslojne cevne sisteme v napeljavah z vročo in hladno vodo za prenos pitne in nepitne vode v stavbah (gospodinjski sistemi) ter za sisteme ogrevanja glede na predvidene tlake in temperature, ki ustrezajo razredu uporabe (glej standard ISO 21003-1:2008, preglednica 1).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST-TS CEN ISO/TS 21003-7:2009
SIST-TS CEN ISO/TS 21003-7:2009/A1:2010
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 7. del:
Navodilo za ugotavljanje skladnosti (ISO/TS 21003-7:2019)
Multilayer piping systems for hot and cold water installations inside buildings - Part 7:
Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation
innerhalb von Gebäuden - Teil 7: Empfehlungen für die Beurteilung der Konformität
(ISO/TS 21003-7:2019)
Systèmes de canalisations multicouches pour installations d'eau chaude et froide à
l'intérieur des bâtiments - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS
21003-7:2019)
Ta slovenski standard je istoveten z: CEN ISO/TS 21003-7:2019
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN ISO/TS 21003-7
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
May 2019
TECHNISCHE SPEZIFIKATION
ICS 23.040.20; 91.140.60 Supersedes CEN ISO/TS 21003-7:2008
English Version
Multilayer piping systems for hot and cold water
installations inside buildings - Part 7: Guidance for the
assessment of conformity (ISO/TS 21003-7:2019)
Systèmes de canalisations multicouches pour Mehrschichtverbund-Rohrleitungssysteme für die
installations d'eau chaude et froide à l'intérieur des Warm- und Kaltwasserinstallation innerhalb von
bâtiments - Partie 7: Guide pour l'évaluation de la Gebäuden - Teil 7: Empfehlungen für die Beurteilung
conformité (ISO/TS 21003-7:2019) der Konformität (ISO/TS 21003-7:2019)
This Technical Specification (CEN/TS) was approved by CEN on 28 March 2019 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 21003-7:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (CEN ISO/TS 21003-7:2019) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 21003-7:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO/TS 21003-7:2019 has been approved by CEN as CEN ISO/TS 21003-7:2019 without any
modification.
TECHNICAL ISO/TS
SPECIFICATION 21003-7
Second edition
2019-04
Multilayer piping systems for hot
and cold water installations inside
buildings —
Part 7:
Guidance for the assessment of
conformity
Systèmes de canalisations multicouches pour installations d'eau
chaude et froide à l'intérieur des bâtiments —
Partie 7: Guide pour l'évaluation de la conformité
Reference number
ISO/TS 21003-7:2019(E)
©
ISO 2019
ISO/TS 21003-7:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO/TS 21003-7:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms and symbols . 4
4.1 Abbreviated terms . 4
4.2 Symbols . 5
5 General . 5
6 Testing and inspection . 5
6.1 Grouping . 5
6.1.1 General. 5
6.1.2 Pressure groups . 5
6.1.3 Size groups . 6
6.1.4 Fitting groups . 6
6.2 Type testing . 6
6.3 Batch release test .15
6.4 Process verification tests (PVTs) .16
6.5 Audit tests (AT) .17
6.6 Indirect testing (IT).17
6.7 Test records.18
Annex A (informative) Interchangeability of different material grades — Testing of
alternative material grades for a layer in a multilayer M-pipe (second sourcing) .19
Bibliography .31
ISO/TS 21003-7:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical
Committee TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2,
Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO/TS 21003-7:2008), which has been
technically revised. It also incorporates the Amendment ISO/TS 21003-7:2008/Amd1: 2010.
The major technical changes are:
— New definition of the terms “material”, “material grade” and “compound”;
— Revision of 6.2 “type testing”;
— Addition of Annex A "Interchangeability of different material grades — Testing of an alternative
material grades for a layer in a Multilayer M-Pipe (second sourcing)”.
A list of all parts in the ISO 21003 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
ISO/TS 21003-7:2019(E)
Introduction
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.