Satellite Earth Stations and Systems (SES); Harmonized EN for Very Small Aperture Terminal (VSAT); Transmit-only, transmit-and-receive, receive-only satellite earth stations operating in the 4 GHz and 6 GHz frequency bands covering essential requirements under article 3.2 of the R&TTE Directive

The present document applies to any Very Small Aperture Terminal (VSAT) which has the following characteristics:
the VSAT is operating in one or more frequency ranges within the following bands allocated to the Fixed Satellite Service (FSS), shared with other services, e.g. the Fixed Service (FS) and the Mobile Service (MS):
- 5,850 GHz to 7,075 GHz (earth-to-space);
- 3,400 GHz to 4,200 GHz (space-to-earth);
the VSAT uses linear or circular polarization;
the VSAT operates through a geostationary satellite at least 3° away from any other geostationary satellite operating in the same frequency band and covering the same area;
the VSAT antenna diameter does not exceed 7,3 m, or equivalent effective area;
the VSAT is either:
- a transmit-only VSAT: designed for transmission-only of radio-communications signals in the frequency band (earth-to-space) specified above; or
- a transmit-and-receive VSAT: designed for transmission-and-reception of radio-communications signals
in the frequency bands specified above; or
- a receive-only VSAT: designed for reception-only of radio-communications signals in the frequency
band (space-to-earth) specified above;
the VSAT is designed usually for unattended operation;
the VSAT is operating as part of a satellite network (e.g. star, mesh or point-to-point) used for the distribution
and/or exchange of information between users;
the transmit-only and transmit-and-receive VSAT is controlled and monitored by a Centralized Control andMonitoring Function (CCMF). The CCMF is outside the scope of the present document.
The present document applies to the VSAT with its ancillary equipment and its various terrestrial ports, and when operated within the boundary limits of the operational environmental profile declared by the applicant and when installed as required by the applicant by declaration or in the user documentation. The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "... radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] may apply to equipment within the scope of the present document.

Satelitske zemeljske postaje in sistemi (SES) – Harmonizirani EN za satelitske terminale z zelo majhno antensko odprtino (VSAT) – oddajne, oddajno-sprejemne ali sprejemne satelitske zemeljske postaje, delujoče v frekvenčnih pasovih 4 GHz in 6 GHz – ki zajema bistvene zahteve člena 3.2 direktive R&TTE

General Information

Status
Published
Publication Date
31-May-2006
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jun-2006
Due Date
01-Jun-2006
Completion Date
01-Jun-2006
Mandate

Relations

Buy Standard

Standard
EN 301 443 V1.3.1:2006
English language
63 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 301 443 V1.3.1:2006
01-junij-2006
6DWHOLWVNH]HPHOMVNHSRVWDMHLQVLVWHPL 6(6 ±+DUPRQL]LUDQL(1]DVDWHOLWVNH
WHUPLQDOH]]HORPDMKQRDQWHQVNRRGSUWLQR 96$7 ±RGGDMQHRGGDMQRVSUHMHPQH
DOLVSUHMHPQHVDWHOLWVNH]HPHOMVNHSRVWDMHGHOXMRþHYIUHNYHQþQLKSDVRYLK*+]
LQ*+]±NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Satellite Earth Stations and Systems (SES); Harmonized EN for Very Small Aperture
Terminal (VSAT); Transmit-only, transmit-and-receive, receive-only satellite earth
stations operating in the 4 GHz and 6 GHz frequency bands covering essential
requirements under article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 301 443 Version 1.3.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 301 443 V1.3.1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 301 443 V1.3.1:2006

---------------------- Page: 2 ----------------------

SIST EN 301 443 V1.3.1:2006

ETSI EN 301 443 V1.3.1 (2006-02)
Candidate Harmonized European Standard (Telecommunications series)

Satellite Earth Stations and Systems (SES);
Harmonized EN for Very Small Aperture Terminal (VSAT);
Transmit-only, transmit-and-receive,
receive-only satellite earth stations operating in the 4 GHz
and 6 GHz frequency bands covering essential requirements
under article 3.2 of the R&TTE Directive

---------------------- Page: 3 ----------------------

SIST EN 301 443 V1.3.1:2006
 2 ETSI EN 301 443 V1.3.1 (2006-02)



Reference
REN/SES-00276
Keywords
regulation, satellite, VSAT
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2006.
All rights reserved.

TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 301 443 V1.3.1:2006
 3 ETSI EN 301 443 V1.3.1 (2006-02)
Contents
Intellectual Property Rights.7
Foreword.7
Introduction .8
1 Scope.10
2 References.11
3 Definitions and abbreviations.11
3.1 Definitions.11
3.2 Abbreviations.13
4 Technical requirements specifications.14
4.1 General.14
4.1.1 Environmental profile.14
4.1.2 Control and Monitoring Functions (CMF).14
4.1.3 Operational configurations.14
4.1.4 Transmit VSAT states and radio states.15
4.1.4.1 Definitions.15
4.1.4.2 Class A CMF.15
4.1.4.3 Class B CMF.15
4.1.4.4 Radio states.15
4.2 Conformance requirements.16
4.2.1 Off-axis spurious radiation .16
4.2.1.1 Justification.16
4.2.1.2 Specification.16
4.2.1.2.1 Transmit VSAT.16
4.2.1.2.2 Receive-only VSAT.17
4.2.1.3 Conformance tests.18
4.2.2 On-axis spurious radiation for transmit VSAT .18
4.2.2.1 Justification.18
4.2.2.2 Specifications.18
4.2.2.2.1 Specification 1: "Carrier-on" radio state.18
4.2.2.2.2 Specification 2: "Carrier-off" and "Emissions disabled radio states".18
4.2.2.3 Conformance tests.18
4.2.3 Off-axis e.i.r.p emission density within the band.18
4.2.3.1 Justification.18
4.2.3.2 Specification.19
4.2.3.3 Conformance tests.20
4.2.4 Carrier suppression.20
4.2.4.1 Justification.20
4.2.4.2 Specification.20
4.2.4.3 Conformance tests.20
4.2.5 Mechanical (antenna pointing) for transmit VSAT .20
4.2.5.1 Justification.20
4.2.5.2 Specification.20
4.2.5.3 Conformance tests.21
4.2.6 Class A Control and Monitoring Functions .21
4.2.6.1 Control and Monitoring Functions (CMF).21
4.2.6.1.1 General.21
4.2.6.1.2 CMF state transition diagram .21
4.2.6.1.3 Specification of states.23
4.2.6.2 Control Channels (CC).23
4.2.6.2.1 Justification.23
4.2.6.2.2 Specification.23
4.2.6.2.3 Conformance tests.23
4.2.6.3 Self monitoring functions.24
ETSI

---------------------- Page: 5 ----------------------

SIST EN 301 443 V1.3.1:2006
 4 ETSI EN 301 443 V1.3.1 (2006-02)
4.2.6.3.1 General.24
4.2.6.3.2 Processor monitoring.24
4.2.6.3.3 Transmit subsystem monitoring.24
4.2.6.3.4 VSAT transmission validation.25
4.2.6.4 Reception of commands from the CCMF .26
4.2.6.4.1 General.26
4.2.6.4.2 Disable message.26
4.2.6.4.3 Enable Message.26
4.2.6.5 Power-on/Reset.27
4.2.6.5.1 Justification.27
4.2.6.5.2 Specification.27
4.2.6.5.3 Conformance tests.27
4.2.7 Class B Control and Monitoring Functions .27
4.2.7.1 Processor monitoring.28
4.2.7.1.1 Justification.28
4.2.7.1.2 Specification.28
4.2.7.1.3 Conformance tests.28
4.2.7.2 Transmit subsystem monitoring.29
4.2.7.2.1 Justification.29
4.2.7.2.2 Specification.29
4.2.7.2.3 Conformance tests.29
4.2.7.3 Power-on/Reset.29
4.2.7.3.1 Justification.29
4.2.7.3.2 Specification.29
4.2.7.3.3 Conformance tests.29
4.2.7.4 Control Channel (CC) reception .29
4.2.7.4.1 Justification.29
4.2.7.4.2 Specification.29
4.2.7.4.3 Conformance tests.30
4.2.7.5 Network control commands .30
4.2.7.5.1 Justification.30
4.2.7.5.2 Specification.30
4.2.7.5.3 Conformance test.30
4.2.7.6 Initial burst transmission .30
4.2.7.6.1 Justification.30
4.2.7.6.2 Specification.30
4.2.7.6.3 Conformance tests.30
5 Testing for compliance with technical requirements.31
5.1 Environmental conditions for testing .31
5.2 Essential radio test suites.31
6 Test methods for the complete VSAT.31
6.1 General.31
6.2 Off-axis spurious radiation.32
6.2.1 Test method.32
6.2.1.0 Multi-carrier operation.33
6.2.1.1 Up to 1 000 MHz .33
6.2.1.1.1 Test site.33
6.2.1.1.2 Measuring receivers.33
6.2.1.1.3 Procedure.33
6.2.1.2 Above 1 000 MHz.34
6.2.1.2.1 Identification of the significant frequencies of spurious radiation .34
6.2.1.2.2 Measurement of radiated power levels of identified spurious radiation.34
6.2.1.2.3 Measurement of conducted spurious radiation at the antenna flange .36
6.3 On-axis spurious radiation for transmit VSAT.37
6.3.1 Test method.37
6.3.1.1 Test site.37
6.3.1.2 Method of measurement.37
6.3.1.2.1 General.37
6.3.1.2.2 Method of measurement at the antenna flange .37
6.3.1.2.3 Method of measurement with a test antenna .38
ETSI

---------------------- Page: 6 ----------------------

SIST EN 301 443 V1.3.1:2006
 5 ETSI EN 301 443 V1.3.1 (2006-02)
6.4 Off-axis e.i.r.p emission density within the band .39
6.4.1 Test method.39
6.4.1.1 General.39
6.4.1.2 Transmit output power density.39
6.4.1.2.1 General.39
6.4.1.2.2 Test site.39
6.4.1.2.3 Method of measurement.40
6.4.1.3 Antenna transmit gain.41
6.4.1.3.1 General.41
6.4.1.3.2 Test site.41
6.4.1.3.3 Method of measurement.41
6.4.1.4 Antenna transmit radiation patterns .42
6.4.1.4.1 General.42
6.4.1.4.2 Test site.42
6.4.1.4.3 Method of measurement.42
6.4.1.4.4 Co-polar radiation pattern -azimuth.42
6.4.1.4.5 Co-polar radiation pattern - elevation.43
6.4.1.4.6 Cross-polar radiation pattern - azimuth .44
6.4.1.4.7 Cross-polar radiation pattern - elevation .44
6.4.2 Computation of results.45
6.5 Carrier suppression.45
6.5.1 Test method.45
6.6 Antenna pointing for transmit VSAT .45
6.6.1 Test method.45
6.7 Class A Control and Monitoring Functions.46
6.7.1 General.46
6.7.2 Test arrangement.46
6.7.3 Control Channels (CC) .47
6.7.3.1 Test method.47
6.7.3.1.1 Test method for internal CC .47
6.7.3.1.2 Test method for external CC .48
6.7.4 Processor monitoring.48
6.7.4.1 Test method.48
6.7.5 Transmit subsystem monitoring.48
6.7.5.1 Test method.48
6.7.6 VSAT transmission validation.49
6.7.6.1 Test method for VSAT validation by the CCMF for VSAT using internal CC .49
6.7.6.2 Test method for VSAT validation by receiving station(s) for VSAT using internal CC.49
6.7.6.3 Test method for transmission validation for VSAT using external CC.49
6.7.7 Reception of commands from the CCMF .49
6.7.7.1 Test method.49
6.7.8 Power-on/Reset.49
6.7.8.1 Test method.49
6.8 Class B Control and Monitoring Functions.50
6.8.1 Test arrangement.50
6.8.2 Processor monitoring - Test method .51
6.8.3 Transmit subsystem monitoring - Test method.51
6.8.4 Power-on/Reset - Test method.52
6.8.5 Control Channel (CC) reception - Test method .52
6.8.6 Network Control commands - Test method.53
6.8.7 Initial burst transmission - Test method.54
7 Test methods for modified VSAT .55
7.1 General.55
7.2 Antenna subsystem replacement.55
Annex A (normative): The EN Requirements Table (EN-RT) .57
Annex B (informative): Pointing stability methodology .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.