SIST EN 14187-1:2017
(Main)Cold applied joint sealants - Test methods - Part 1: Determination of rate of cure
Cold applied joint sealants - Test methods - Part 1: Determination of rate of cure
This European Standard applies to the determination of the rate of cure of cold applied joint sealants indicated by the build up of the tensile modulus during the cure.
Kalt verarbeitbare Fugenmassen - Teil 1: Prüfverfahren zur Bestimmung des Aushärtungsgrades
Diese Europäische Norm gilt für die Bestimmung des Aushärtungsgrades von kalt verarbeitbaren Fugen-massen, der durch den Anstieg des Zugspannungswertes während der Aushärtung angezeigt wird.
Mastics pour joints appliqués à froid - Méthodes d'essai - Partie 1: Détermination du taux de polymérisation
La présente Norme européenne s'applique à la détermination du taux de polymérisation des mastics pour joints appliqués à froid indiquée par la constitution du module de traction pendant la polymérisation.
Hladno nanosljive tesnilne mase za stike - Preskusne metode - 1. del: Ugotavljanje stopnje strditve
Ta evropski standard se uporablja za ugotavljanje stopnje strditve hladno nanosljivih tesnilnih mas za stike s kopičenjem nateznih modulov med strjevanjem.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hladno nanosljive tesnilne mase za stike - Preskusne metode - 1. del: Ugotavljanje stopnje strditveKalt verarbeitbare Fugenmassen - Teil 1: Prüfverfahren zur Bestimmung des AushärtungsgradesMastics pour joints appliqués à froid - Méthodes d'essai - Partie 1: Détermination du taux de polymérisationCold applied joint sealants - Test methods - Part 1: Determination of rate of cure93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 14187-1:2017SIST EN 14187-1:2017en,fr,de01-september-2017SIST EN 14187-1:2017SLOVENSKI
STANDARDSIST EN 14187-1:20041DGRPHãþD
SIST EN 14187-1:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14187-1
June
t r s y ICS
{ uä r z rä t r Supersedes EN
s v s z yæ sã t r r uEnglish Version
Cold applied joint sealants æ Test methods æ Part
sã Determination of rate of cure Mastics pour joints appliqués à froid æ Méthodes d 5essai æ Partie
sã Détermination du taux de polymérisation
Kalt verarbeitbare Fugenmassen æ Prüfverfahren æ Teil
sã Bestimmung des Aushärtungsgrades This European Standard was approved by CEN on
s y April
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v s z yæ sã t r s y ESIST EN 14187-1:2017
EN 14187-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus and materials . 4 6 Preparation of test specimens . 4 7 Procedure. 5 8 Calculation and expression of results . 6 9 Test report . 6
SIST EN 14187-1:2017
EN 14187-1:2017 (E) 3 European foreword This document (EN 14187-1:2017) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2017, and conflicting national standards shall be withdrawn at the latest by December 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14187-1:2003. Apart from editorial changes no major changes have been made in this revision. This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants — Test methods — Part 1: Determination of rate of cure. EN 14187-2, Cold applied joint sealants — Test methods — Part 2: Determination of tack free time. EN 14187-3, Cold applied joint sealants — Test methods — Part 3: Determination of self-levelling properties. EN 14187-4, Cold applied joint sealants — Test methods — Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals. EN 14187-5, Cold applied joint sealants — Test methods — Part 5: Determination of the resistance to hydrolysis. EN 14187-6, Cold applied joint sealants — Test methods — Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals. EN 14
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.