SIST EN ISO 6224:2011
(Main)Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011)
Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011)
This International Standard specifies the requirements for general-purpose textile-reinforced thermoplastics
water-discharge hoses.
Three types of hose are specified according to their operating duty requirements, i.e. their ambient and water
temperature ranges:
— ambient temperatures: −10 °C to +60 °C;
— water temperature during operation: 0 °C to +60 °C.
NOTE At water temperatures above 23 °C and particularly above 40 °C, the maximum working pressure will be reduced.
These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine
inlets, as fire-fighting hoses, for special agricultural machines or as gardening hoses for the consumer market.
Einführendes Element - Haupt-Element - Ergänzendes Element (ISO 6224:2011)
Diese Internationale Norm legt die Anforderungen an Kunststoffschläuche mit Textileinlage für allgemeine Anwendungen mit Wasser fest.
Drei Arten von Schläuchen sind entsprechend ihrer Eignung für betriebliche Anforderungen beschrieben, wie z. B. für Umgebungs- und Wassertemperaturbereiche von:
Umgebungstemperaturen: 10 °C bis 60 °C;
Betriebstemperaturbereich: 0 °C bis 60 °C.
ANMERKUNG Bei Temperaturen über 23 °C und insbesondere über 40 °C wird der maximale Betriebsdruck reduziert.
Diese Schläuche sind nicht vorgesehen für die Verwendung beim Transport von Trinkwasser, an Wasch-maschineneinlässen, bei der Brandbekämpfung, bei speziellen Landwirtschaftsmaschinen oder als Garten¬schlauch für den privaten Gebrauch.
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau - Spécifications (ISO 6224:2011)
La présente Norme internationale spécifie les exigences relatives aux tuyaux d'usage général, en matières
thermoplastiques à armature textile pour refoulement d'eau.
Trois types de tuyaux sont spécifiés en fonction de leurs conditions de service, c'est-à-dire leurs plages de
températures ambiantes et de températures d'eau:
— températures ambiantes: −10 °C à +60 °C;
— températures d'eau en service: 0 °C à +60 °C.
NOTE Pour des températures d'eau supérieures à 23 °C et particulièrement supérieures à 40 °C, la pression
maximale de service sera réduite.
Ces tuyaux ne sont pas destinés à être utilisés pour le transport d'eau potable, le raccordement de machine à
laver, comme tuyaux d'incendie, pour les machines agricoles spéciales ou comme tuyaux d'arrosage pour le
marché grand public.
S tekstilom ojačene plastomerne cevi za splošno uporabo vode - Specifikacija (ISO 6224:2011)
Ta mednarodni standard določa zahteve za s tekstilom ojačene plastomerne cevi za splošno uporabo odvajanja vode.
Določene so tri vrste cevi glede na njihove zahteve za delovanje, tj. razpone temperature okolja in vode:
- okoljske temperature: -10 °C do +60 °C,
— temperatura vode med obratovanjem: 0 °C do +60 °C.
OPOMBA: Pri temperaturah vode nad 23 °C in še zlasti nad 40 °C se maksimalni delovni tlak zniža.
Te cevi niso namenjene uporabi za prenos pitne vode, za dotoke v pralne stroje, kot požarne cevi, za posebne kmetijske stroje ali kot vrtne cevi za potrošniški trg.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6224:2011
01-december-2011
1DGRPHãþD
SIST EN ISO 6224:2009
6WHNVWLORPRMDþHQHSODVWRPHUQHFHYL]DVSORãQRXSRUDERYRGH6SHFLILNDFLMD ,62
Thermoplastics hoses, textile-reinforced, for general-purpose water applications -
Specification (ISO 6224:2011)
Einführendes Element - Haupt-Element - Ergänzendes Element (ISO 6224:2011)
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau -
Spécifications (ISO 6224:2011)
Ta slovenski standard je istoveten z: EN ISO 6224:2011
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 6224:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6224:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 6224:2011
EUROPEAN STANDARD
EN ISO 6224
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2011
ICS 23.040.70 Supersedes EN ISO 6224:2008
English Version
Thermoplastics hoses, textile-reinforced, for general-purpose
water applications - Specification (ISO 6224:2011)
Tuyaux en matières thermoplastiques à armature textile Kunststoffschläuche mit Textileinlage für allgemeine
d'usage général pour l'eau - Spécifications (ISO 6224:2011) Anwendungen mit Wasser - Anforderung (ISO 6224:2011)
This European Standard was approved by CEN on 30 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6224:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6224:2011
EN ISO 6224:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6224:2011
EN ISO 6224:2011 (E)
Foreword
This document (EN ISO 6224:2011) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6224:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 6224:2011 has been approved by CEN as a EN ISO 6224:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6224:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 6224:2011
INTERNATIONAL ISO
STANDARD 6224
Fourth edition
2011-10-01
Thermoplastics hoses, textile-reinforced,
for general-purpose water applications —
Specification
Tuyaux en matières thermoplastiques à armature textile d’usage
général pour l’eau — Spécifications
Reference number
ISO 6224:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 6224:2011
ISO 6224:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 6224:2011
ISO 6224:2011(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 2
5 Materials and construction . 2
6 Dimensions . 2
6.1 Inside diameters and tolerances on inside diameter . 2
6.2 Concentricity . 3
6.3 Tolerance on length . 3
6.4 Minimum wall thickness . 3
7 Physical properties . 3
7.1 Thermoplastic materials . 3
7.2 Finished hoses . 4
8 Type, routine and production testing . 4
9 Test certificate/report . 4
10 Marking . 5
11 Recommendations for packaging and storage . 5
Annex A (normative) Type testing and routine testing . 6
Annex B (informative) Recommended tests for production testing . 7
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 6224:2011
ISO 6224:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6224 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Hoses (rubber and plastics).
This fourth edition cancels and replaces the third edition (ISO 6224:2005), which has been technically revised.
The main changes are as follows:
— Table 1 includes four additional inside diameters (4 mm, 6 mm, 8 mm and 9 mm) for each type of hose;
— in Table 3, the requirement for the minimum adhesion between components has been raised from
1,5 kN/m to 2,0 kN/m;
— annexes giving schedules for type, routine and production testing have been added.
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 6224:2011
INTERNATIONAL STANDARD ISO 6224:2011(E)
Thermoplastics hoses, textile-reinforced, for general-purpose
water applications — Specification
WARNING — Persons using this International Standard should be familiar with normal laboratory
practice. This standard does not purport to address all the safety problems, if any, associated with
its use. It is the responsibility of the user to establish appropriate health and safety practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This International Standard specifies the requirements for general-purpose textile-reinforced thermoplastics
water-discharge hoses.
Thr
...
SLOVENSKI STANDARD
oSIST prEN ISO 6224:2009
01-september-2009
6WHNVWLORPRMDþHQHSODVWRPHUQHFHYL]DVSORãQRXSRUDERYRGH6SHFLILNDFLMD
,62',6
Thermoplastics hoses, textile-reinforced, for general-purpose water applications -
Specification (ISO/DIS 6224:2009)
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau -
Spécifications (ISO/DIS 6224:2009)
Ta slovenski standard je istoveten z: prEN ISO 6224
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
oSIST prEN ISO 6224:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 6224:2009
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6224:2009
EUROPEAN STANDARD
DRAFT
prEN ISO 6224
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2009
ICS 23.040.70 Will supersede EN ISO 6224:2008
English Version
Thermoplastics hoses, textile-reinforced, for general-purpose
water applications - Specification (ISO/DIS 6224:2009)
Tuyaux en matières thermoplastiques à armature textile
d'usage général pour l'eau - Spécifications (ISO/DIS
6224:2009)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 218.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 6224:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6224:2009
prEN ISO 6224:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6224:2009
prEN ISO 6224:2009 (E)
Foreword
This document (prEN ISO 6224:2009) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 6224:2008.
Endorsement notice
The text of ISO/DIS 6224:2009 has been approved by CEN as a prEN ISO 6224:2009 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6224:2009
---------------------- Page: 6 ----------------------
oSIST prEN ISO 6224:2009
DRAFT INTERNATIONAL STANDARD ISO/DIS 6224
ISO/TC 45/SC 1 Secretariat: DSM
Voting begins on: Voting terminates on:
2009-05-21 2009-10-21
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Thermoplastics hoses, textile-reinforced, for general-purpose
water applications — Specification
Tuyaux en matières thermoplastiques à armature textile d'usage général pour l'eau — Spécifications
[Revision of third edition (ISO 6224:2005)]
ICS 23.040.70
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2009
---------------------- Page: 7 ----------------------
oSIST prEN ISO 6224:2009
ISO/DIS 6224
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 6224:2009
ISO/DIS 6224
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Classification. 2
5 Materials and construction . 2
6 Dimensions. 2
7 Physical properties. 3
8 Marking . 5
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 6224:2009
ISO/DIS 6224
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is no
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.