SIST EN ISO 11393-5:2019
(Main)Protective clothing for users of hand-held chainsaws - Part 5: Performance requirements and test methods for protective gaiters (ISO 11393-5:2018)
Protective clothing for users of hand-held chainsaws - Part 5: Performance requirements and test methods for protective gaiters (ISO 11393-5:2018)
This part of ISO 11393 specifies requirements and the test methods to be used to assess the resistance of gaiters to cutting by hand-held chain-saws and other properties. A requirement and a test method for assessing the strength of underfoot straps of gaiters is also included.
This part of ISO 11393 is applicable to gaiters which are to be used in conjunction with safety footwear with a steel toecap complying with ISO 20345 design “C” or “D”,. These gaiters shall be designed to be used only in association with a specific footwear and tested together.
This part of ISO 11393 is not applicable to gaiters intended for use in situations where there is a significant risk of tripping such as tree climbing or in forests.
Schutzkleidung für Benutzer von handgeführten Kettensägen - Teil 5: Prüfverfahren und Leistungsanforderungen für Schutzgamaschen (ISO 11393-5:2018)
Dieser Teil von ISO 11393 legt Anforderungen und Prüfverfahren zur Ermittlung des Schnittwiderstands von Gamaschen gegen Schnitte durch handgeführte Kettensägen und andere Eigenschaften fest. Eine Anforderung und ein Prüfverfahren zur Ermittlung der Festigkeit der Fußschlaufen von Gamaschen sind ebenfalls enthalten.
Dieser Teil von ISO 11393 gilt für Gamaschen, die in Verbindung mit Sicherheitsschuhen mit Zehenkappe aus Stahl nach ISO 20345, Form „C“ oder „D“, verwendet werden. Diese Gamaschen müssen für die ausschlie߬liche Verwendung zusammen mit einem festgelegten Schuhwerk ausgelegt werden und zusammen geprüft werden.
Diese Produkte sind für die hauptsächliche Verwendung in Kombination mit einem festgelegten ortho-pädischen Schuhwerk vorgesehen.
Dieser Teil von ISO 11393 gilt nicht für Gamaschen, die für den Gebrauch in Situationen mit signifikantem Stolperrisiko bestimmt sind, wie bei der Arbeit im Wald oder beim Besteigen von Bäumen.
Vêtements de protection pour utilisateurs de scies à chaîne tenues à la main - Partie 5: Exigences de performance et méthodes d'essai pour guêtres de protection (ISO 11393-5:2018)
Le présent document spécifie les exigences et les méthodes d'essais pour évaluer la résistance des guêtres aux coupures dues aux scies à chaîne tenues à la main, ainsi que d'autres propriétés. Il comprend une exigence et une méthode d'essai pour l'évaluation de la résistance des brides passant sous le pied de guêtres.
Le présent document est applicable aux guêtres utilisées avec des chaussures de sécurité avec un embout en acier conformes à l'ISO 20345, type «C» ou «D». Ces guêtres sont conçues pour n'être utilisées que conjointement avec des chaussures définies et pour être soumises à essai avec elles.
NOTE Ces produits sont destinés à être utilisés, sans toutefois s'y limiter, en association avec un modèle défini de chaussures orthopédiques.
Le présent document ne s'applique pas aux guêtres prévues pour être utilisées dans des situations où il existe un risque significatif de trébucher, telles que grimper aux arbres ou en forêt.
Varovalna obleka za uporabnike ročnih verižnih žag - 5. del: Zahtevane lastnosti in preskusne metode za zaščitne dokolenice (gamaše) (ISO 11393-5:2018)
Ta del standarda ISO 11393 določa zahteve in preskusne metode, ki se uporabljajo za vrednotenje odpornosti gamaš proti urezu z ročnimi verižnimi žagami in drugih lastnosti. Vključeni sta tudi zahteva in preskusna metoda za vrednotenje trdnostni trakov gamaš. Ta del standarda ISO 11393 se uporablja za gamaše, ki se uporabljajo skupaj z zaščitno obutvijo z jekleno kapico, skladno z zasnovo »C« ali »D« iz standarda ISO 20345. Te gamaše je treba zasnovati tako, da se uporabljajo samo z določeno obutvijo in se preskušajo skupaj. Ta del standarda ISO 11393 se ne uporablja za gamaše, ki so namenjene uporabi v primerih, pri katerih obstaja znatno tveganje za spotikanje, npr. pri plezanju po drevesih ali v gozdovih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11393-5:2019
01-oktober-2019
Nadomešča:
SIST EN 381-8:1998
SIST EN 381-9:1998
Varovalna obleka za uporabnike ročnih verižnih žag - 5. del: Zahtevane lastnosti in
preskusne metode za zaščitne dokolenice (gamaše) (ISO 11393-5:2018)
Protective clothing for users of hand-held chainsaws - Part 5: Performance requirements
and test methods for protective gaiters (ISO 11393-5:2018)
Schutzkleidung für Benutzer von handgeführten Kettensägen - Teil 5: Prüfverfahren und
Leistungsanforderungen für Schutzgamaschen (ISO 11393-5:2018)
Vêtements de protection pour utilisateurs de scies à chaîne tenues à la main - Partie 5:
Exigences de performance et méthodes d'essai pour guêtres de protection (ISO 11393-
5:2018)
Ta slovenski standard je istoveten z: EN ISO 11393-5:2019
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
SIST EN ISO 11393-5:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11393-5:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 11393-5:2019
EN ISO 11393-5
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 13.340.10 Supersedes EN 381-8:1997, EN 381-9:1997
English Version
Protective clothing for users of hand-held chainsaws - Part
5: Performance requirements and test methods for
protective gaiters (ISO 11393-5:2018)
Vêtements de protection pour utilisateurs de scies à Schutzkleidung für Benutzer von handgeführten
chaîne tenues à la main - Partie 5: Exigences de Kettensägen - Teil 5: Prüfverfahren und
performance et méthodes d'essai pour guêtres de Leistungsanforderungen für Schutzgamaschen (ISO
protection (ISO 11393-5:2018) 11393-5:2018)
This European Standard was approved by CEN on 18 July 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11393-5:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11393-5:2019
EN ISO 11393-5:2019 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of REGULATION (EU) 2016/425 aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11393-5:2019
EN ISO 11393-5:2019 (E)
European foreword
This document (EN ISO 11393-5:2019) has been prepared by Technical Committee ISO/TC 94
"Personal safety - Personal protective equipment" in collaboration with Technical Committee CEN/TC
162 “Protective clothing including hand and arm protection and lifejackets” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 381-8:1997 and EN 381-9:1997.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11393-5:2018 has been approved by CEN as EN ISO 11393-5:2019 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11393-5:2019
EN ISO 11393-5:2019 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of REGULATION (EU) 2016/425 aimed to be covered
This European Standard has been prepared under a Commission’s standardization request to provide
one voluntary means of conforming to essential requirements of Regulation (EU) 2016/425 on the
approximation of the laws of the Member States relating to personal protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Regulation,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits
of the scope of this standard, a presumption of conformity with the corresponding essential
requirements of that Regulation and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex II of the REGULATION
(EU) 2016/425 Personal Protective Equipment
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
REGULATION (EU) 2016/425 of this EN
1.1.1 Ergonomics 4.7
1.1.2.1. Optimum level of protection 4.7
1.1.2.2. Classes of protection appropriate 4.5
to different levels of risk
1.2.1 Absence of inherent risks and 4.2.1; 4.2.3; 4.4
other nuisance factors
1.2.1.1. Suitable constituent materials 4.3
1.2.1.3. Maximum permissible user 4.7
impediment
1.3.1 Adaptation of PPE to user 6.5
morphology
1.3.2. Lightness and strength 4.2.2
1.3.3 Compatibility of different classes 8; 10
or types of PPE designed for
simultaneous use
1.4. Manufacturer’s instructions 10
and information
2.1. PPE incorporating adjustment 4.7
systems
2.4. PPE subject to ageing 8; 10
4
---------------------- Page: 6 ----------------------
SIST EN ISO 11393-5:2019
EN ISO 11393-5:2019 (E)
2.12. PPE bearing one or more 9
identification markings or indicators
directly or indirectly relating to health
and safety
3.3 Protection against mechanical 4.6
injuries
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
5
---------------------- Page: 7 ----------------------
SIST EN ISO 11393-5:2019
---------------------- Page: 8 ----------------------
SIST EN ISO 11393-5:2019
INTERNATIONAL ISO
STANDARD 11393-5
Second edition
2018-09
Protective clothing for users of hand-
held chainsaws —
Part 5:
Performance requirements and test
methods for protective gaiters
Vêtements de protection pour utilisateurs de scies à chaîne tenues à
la main —
Partie 5: Exigences de performance et méthodes d'essai pour guêtres
de protection
Reference number
ISO 11393-5:2018(E)
©
ISO 2018
---------------------- Page: 9 ----------------------
SIST EN ISO 11393-5:2019
ISO 11393-5:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11393-5:2019
ISO 11393-5:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 General . 2
4.2 Fasteners . 2
4.2.1 General. 2
4.2.2 Attachment system . 2
4.2.3 Twisting resistance of the gaiter . 2
4.3 Innocuousness . 2
4.4 Specified protective area . 3
4.5 Classification according to chain speed . 3
4.6 Cut resistance . 3
4.7 Ergonomics . 3
5 Pre-treatment . 4
6 Test methods . 4
6.1 Test samples . 4
6.2 Resistance to the chainsaw. 4
6.2.1 Principle . 4
6.2.2 Test specimens. 4
6.2.3 Apparatus . 4
6.3 Strength of the attachment system . 4
6.3.1 Principle . 4
6.3.2 Test samples. 5
6.3.3 Apparatus . 5
6.3.4 Preparing and fixing of samples for testing and procedure . 5
6.4 Twisting resistance of the gaiter . 5
6.4.1 Principle . 5
6.4.2 Test specimens. 5
6.4.3 Test equipment . 6
6.4.4 Procedure . 6
6.5 Ergonomic testing . 6
6.5.1 Ergonomic assessment . 6
6.5.2 Procedures . 7
7 Test report . 7
8 Marking . 8
9 Pictogram . 8
10 Information to be supplied by the manufacturer . 9
Bibliography .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 11393-5:2019
ISO 11393-5:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in
collaboration with ISO Technical Committee TC 94, Personal safety — Personal protective equipment,
Subcommittee SC 13, Protective clothing, in accordance with the agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 11393-5:2001), which has been technically
revised. The whole document and the Scope have been revised. The main changes compared to the
previous edition are as follows:
— in the Introduction, the term “hand-held chainsaws primarily constructed for cutting wood” has
been added;
— the normative references have been updated;
— terms and definitions have been added;
— a conjunction of the gaiter to a defined boot for test purposes has become mandatory;
— requirements and test methods for ergonomic properties, twisting resistance, the strength of the
attachment system and innocuousness have been added;
— requirements for protective coverage have been changed;
— class 0 has been deleted from the requirements to cut resistance;
— the pre-treatment procedure has been revised.
A list of all parts in the ISO 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.