SIST EN 2267-010:2017
(Main)Aerospace series - Cables, electrical, for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard
Aerospace series - Cables, electrical, for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard
This European Standard specifies the characteristics of UV laser printable electrical lightweight wires DR
family for use in the on-board 115 V (phase to neutral) or 200 V (phase to phase) AC electrical systems
of aircraft at operating temperatures between − 65 °C and 260 °C. These cables are demonstrated to be
arc resistant in sizes AWG 26 to 14 (115/200 V AC).
In addition, these cables may be suitable for use at 230/400 V AC in pressurised zones only when installed
to take account of possible short circuit effects.
It shall also be possible to mark these cables by qualified compatible marking. These markings shall
satisfy the requirements of EN 3838.
Luft- und Raumfahrt - Leitungen, elektrisch, für allgemeine Verwendung - Betriebstemperaturen zwischen - 55 °C und 260 °C - Teil 010: DR-Familie Einadrige Leitungen UV-Laser bedruckbar - Produktnorm –
Série aérospatiale - Câbles, électriques, d'usage général - Températures de fonctionnement comprises entre - 55 °C et 260 °C - Partie 010: Famille DR, fil simple marquable au laser UV - Norme de produit
Aeronavtika - Električni kabli za splošno uporabo - Delovne temperature med –55 °C in 260 °C - 010. del: Družina DR, enožilni kabli z možnostjo UV-laserskega tiskanja - Standard za proizvod
Ta evropski standard določa karakteristike družine električnih kablov z možnostjo UV-laserskega tiskanja iz družine DR za uporabo na krovu v električnih sistemih letala s 115 V (faza, zvezana z nevtralno napetostjo) ali 200 V (faza, zvezana s fazo) pri temperaturi delovanja med –65 °C in 260 °C. Ti kabli so dokazano odporni proti obloku v velikostih od 26 do 14 AWG (115/200 V AC).
Poleg tega se lahko te kable uporablja pri 230/400 V AC v conah pod tlakom le, če so nameščeni, da se upoštevajo možni učinki kratkega stika.
Te kable je treba označiti s kvalificirano združljivo oznako. Te oznake morajo biti v skladu z zahtevami standarda EN 3838.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ODVHUVNHJDLuft- und Raumfahrt - Leitungen, elektrisch, für allgemeine Verwendung - Betriebstemperaturen zwischen - 55 °C und 260 °C - Teil 010: DR-Familie Einadrige Leitungen UV-Laser bedruckbar - Produktnorm
–Série aérospatiale - Câbles, électriques, d'usage général - Températures de fonctionnement comprises entre - 55 °C et 260 °C - Partie 010: Famille DR, fil simple marquable au laser UV - Norme de produitAerospace series - Cables, electrical, for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard49.060Aerospace electric equipment and systems29.060.20KabliCablesICS:Ta slovenski standard je istoveten z:EN 2267-010:2017SIST EN 2267-010:2017en,fr,de01-oktober-2017SIST EN 2267-010:2017SLOVENSKI
STANDARDSIST EN 2267-010:20141DGRPHãþD
SIST EN 2267-010:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2267-010
August
t r s y ICS
v {ä r x r Supersedes EN
t t x yæ r s rã t r s uEnglish Version
Aerospace series æ Cablesá electricalá for general purpose æ Operating temperatures between æ w w
¹C and
t x r
¹C æ Part
r s rã DR familyá single UV laser printable æ Product standard Série aérospatiale æ Câblesá électriquesá d 5usage général æ Températures de fonctionnement comprises entre æ w w
¹C et
t x r
¹C æ Partie
r s rã Famille DRá fil simple marquable au laser UV æ Norme de produit
Luftæ und Raumfahrt æ Leitungená elektrischá für allgemeine Verwendung æ Betriebstemperaturen zwischen æ w w
¹C und
t x r
¹C æ Teil
r s rã DRæFamilie Einadrige Leitungen UVæLaser bedruckbar æ Produktnorm This European Standard was approved by CEN on
t r February
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t t x yæ r s rã t r s y ESIST EN 2267-010:2017
EN 2267-010:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms, definitions, symbols and abbreviations . 4 4 Materials and construction . 5 5 Required characteristics . 6 6 Quality assurance . 9 7 Designation . 9 8 Identification and marking . 10 9 Packaging, labelling and delivery lengths . 10 10 Technical specification . 10
SIST EN 2267-010:2017
EN 2267-010:2017 (E) 3 European foreword This document (EN 2267-010:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2018, and conflicting national standards shall be withdrawn at the latest by February 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 2267-010:2013. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 2267-010:2017
EN 2267-010:2017 (E) 4 1 Scope This European Standard specifies the characteristics of UV laser printable electrical lightweight wires DR family for use in the on-board 115 V (phase to neutral) or 200 V (phase to phase) AC electrical systems of aircraft at operating temperatures between − 65 °C and 260 °C. These cables are demonstrated to be arc resistant in sizes AWG 26 to 14 (115/200 V AC). In addition, these cables may be suitable for use at 230/400 V AC in pressurised zones only when installed to take account of possible short circuit effects. It shall also be possible to mark these cables by qualified compatible marking. These markings shall satisfy the requirements of EN 3838. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2083, Aerospace series — Copper and copper alloys conductors for electrical cables — Product standard EN 2084, Aerospace series — Cables, electrical, general purpose, with conductors in copper or copper alloy — Technical specification EN 2267-002, Aerospace series — Cables, electri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.