iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST IEC 60308:1999

(Main)

Hydraulic turbines - Testing of control systems

Hydraulic turbines - Testing of control systems

Deals with the definition and the characteristics of control systems. It is not limited to the actual controller tasks but also includes other tasks which may be assigned to a control system, such as sequence control tasks, safety and provision for the actuating energy. The following systems are included, speed, power, opening, water level and flow control for all turbine types; electronic, electrical and fluid power devices; safety devices as well as start-up and shutdown devices.

Turbines hydrauliques - Essais des systèmes de régulation

Traite de la définition et des caractéristiques des systèmes de régulation.  Elle n'est pas limitée aux tâches effectives de régulation, mais inclut également d'autres tâches qui peuvent être assignées à un système de régulation, telles que les tâches de commande séquentielle, de sécurité, d'alimentation en énergie de manoeuvre.  La présente norme couvre les systèmes suivants : régulation de vitesse, puissance, ouverture, niveau d'eau et débit de tous types de turbines; dispositifs électroniques, électriques et d'alimentation en fluide;  dispositifs de sécurité; dispositifs de démarrage, et dispositifs d'arrêt.

Mednarodna pravila za preskušanje regulacije hitrosti krmilnih sistemov vodnih turbin

General Information

Status
Withdrawn
Publication Date
31-Mar-1999
Withdrawal Date
19-Apr-2016
ICS
27.140 - Hydraulic energy engineering
Technical Committee
IEHT - Electrotechnics - Hydraulic turbins
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
19-Apr-2016
Due Date
12-May-2016
Completion Date
20-Apr-2016
Ref Project
IEC 60308 - Hydraulic turbines - Testing of control systems

Buy Standard

IEC 60308:1999IEC 60308:1999
PreviousNext
Standard
IEC 60308:1999
English language
50 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST IEC 60308:1999
01-april-1999
Mednarodna pravila za preskušanje regulacije hitrosti krmilnih sistemov vodnih
turbin
Hydraulic turbines - Testing of control systems
Turbines hydrauliques - Essais des systèmes de régulation
Ta slovenski standard je istoveten z: IEC 60308
ICS:
27.140 Vodna energija Hydraulic energy engineering
SIST IEC 60308:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST IEC 60308:1999

---------------------- Page: 2 ----------------------

SIST IEC 60308:1999

---------------------- Page: 3 ----------------------

SIST IEC 60308:1999

---------------------- Page: 4 ----------------------

SIST IEC 60308:1999

---------------------- Page: 5 ----------------------

SIST IEC 60308:1999

---------------------- Page: 6 ----------------------

SIST IEC 60308:1999

---------------------- Page: 7 ----------------------

SIST IEC 60308:1999

---------------------- Page: 8 ----------------------

SIST IEC 60308:1999

---------------------- Page: 9 ----------------------

SIST IEC 60308:1999

---------------------- Page: 10 ----------------------

SIST IEC 60308:1999

---------------------- Page: 11 ----------------------

SIST IEC 60308:1999

---------------------- Page: 12 ----------------------

SIST IEC 60308:1999

---------------------- Page: 13 ----------------------

SIST IEC 60308:1999

---------------------- Page: 14 ----------------------

SIST IEC 60308:1999

---------------------- Page: 15 ----------------------

SIST IEC 60308:1999

---------------------- Page: 16 ----------------------

SIST IEC 60308:1999

---------------------- Page: 17 ----------------------

SIST IEC 60308:1999

---------------------- Page: 18 ----------------------

SIST IEC 60308:1999

---------------------- Page: 19 ----------------------

SIST IEC 60308:1999

---------------------- Page: 20 ----------------------

SIST IEC 60308:1999

---------------------- Page: 21 ----------------------

SIST IEC 60308:1999

---------------------- Page: 22 ----------------------

SIST IEC 60308:1999

---------------------- Page: 23 ----------------------

SIST IEC 60308:1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 63132-6:2023(Main)
Guidance for installation procedures and tolerances of hydroelectric machines - Part 6: Vertical Pelton turbines (IEC 63132-6:2023)
EN IEC 63132-6:2023

IEC 63132-6:2023 is to establish, in a general way, suitable procedures and tolerances for the installation of Pelton vertical turbines. This document presents a typical assembly and whenever the word "turbine" is used in this document, it refers to a vertical Pelton turbine. There are many possible ways to assemble a unit. The size of the machine, the design of the machine, the layout of the powerhouse or the delivery schedule of the components are some of the elements that could result in additional steps, or the elimination of some steps and/or assembly sequences.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63132-5:2023(Main)
Guide for installation procedures and tolerances of hydroelectric machines - Part 5: Bulb turbines and generators (IEC 63132-5:2023)
EN IEC 63132-5:2023

The purpose of this guide is to establish, in a general way, suitable procedures and tolerances for the installation of bulb turbine and generator. This guide presents a typical assembly and whenever the words "turbine" and "generator" are used in this part, it refers to bulb turbine and generator. There are many possible ways to assemble a unit. The size of the machine, the design of the machine, the layout of the powerhouse, the sequence of concreting or the delivery schedule of the components are some of the elements that could result in additional steps, or the elimination of some steps and/or assembly sequences.
It is understood that a publication of this type will be binding only if, and to the extent that, both contracting parties have agreed upon it.
The guide excludes matters of purely commercial interest, except those inextricably bound up with the conduct of installation. It also excluded to specifications of the civil works but this aspect of the work should be taken into consideration during the assembly of the units.
Wherever the guide specifies that documents, drawings or information is supplied by a manufacturer (or by manufacturers), each individual manufacturer will furnish the appropriate information for their own supply only.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63132-3:2020(Main)
Guidance for installation procedures and tolerances of hydroelectric machines - Part 3: Vertical Francis turbines or pump-turbines (IEC 63132-3:2020)
EN IEC 63132-3:2020

The purpose of this this part of IEC 63132 is to establish, in a general way, suitable procedures
and tolerances for the installation of a vertical Francis turbine or pump-turbine. This document
presents a typical assembly and whenever the word “turbine” is used in this document, it refers
to a vertical Francis turbine or a pump-turbine. There are many possible ways to assemble a
unit. The size of the machine, design of the machine, layout of the powerhouse or delivery
schedule of the components are some of the elements that could result in additional steps, the
elimination of some steps and/or assembly sequences.
It is understood that a publication of this type will be binding only if, and to the extent that, both
contracting parties have agreed upon it.
This document excludes matters of purely commercial interest, except those inextricably bound
up with the conduct of installation.
The tolerances in this document have been established upon best practices and experience,
although it is recognized that other standards specify different tolerances.
Wherever this document specifies that documents, drawings or information is supplied by a
manufacturer (or by manufacturers), each individual manufacturer will furnish the appropriate
information for their own supply only.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63132-4:2020(Main)
Guidance for installation procedures and tolerances of hydroelectric machines - Part 4: Vertical Kaplan or propeller turbines (IEC 63132-4:2020)
EN IEC 63132-4:2020

The purpose of this this part of IEC 63132 is to establish, in a general way, suitable
procedures and tolerances for the installation of a vertical Kaplan or propeller turbine. This
document presents a typical assembly and whenever the word “turbine” is used in this
document, it refers to a vertical Kaplan or propeller turbine. There are many possible ways to
assemble a unit. The size of the machine, design of the machine, layout of the powerhouse or
delivery schedule of the components are some of the elements that could result in additional
steps, the elimination of some steps and/or assembly sequences.
It is understood that a publication of this type will be binding only if, and to the extent that,
both contracting parties have agreed upon it.
This document excludes matters of purely commercial interest, except those inextricably
bound up with the conduct of installation.
The tolerances in this document have been established upon best practices and experience,
although it is recognized that other standards specify different tolerances.
Wherever this document specifies that documents, drawings or information is supplied by a
manufacturer (or by manufacturers), each individual manufacturer will furnish the appropriate
information for their own supply only.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63132-2:2020(Main)
Guide for installation procedures and tolerances of hydroelectric machines - Part 2: Vertical generator (IEC 63132-2:2020)
EN IEC 63132-2:2020

The purpose of this part of IEC 63132 is to establish, in a general way, suitable procedures and
tolerances for installation of generator. This document presents a typical assembly. There are
many possible ways to assemble a unit. The size of the machines, design of the machines,
layout of the powerhouse or delivery schedule of the components are some of the elements that
could result in additional steps, the elimination of some steps and/or assembly sequences.
It is understood that a publication of this type will be binding only if, and to the extent that, both
contracting parties have agreed upon it.
This document excludes matters of purely commercial interest, except those inextricably bound
up with the conduct of installation.
This document applies to vertical generators according to IEC 60034-7 1.
The tolerances in this document have been established upon best practices and experience,
although it is recognized that other standards specify different tolerances.
Brushless excitation system is not included in this document.
Wherever this document specifies that documents, drawings or information is supplied by a
manufacturer (or by manufacturers), each individual manufacturer will furnish the appropriate
information for their own supply only.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63132-1:2020(Main)
Guidance for installation procedures and tolerances of hydroelectric machines - Part 1: General aspects (IEC 63132-1:2020)
EN IEC 63132-1:2020

The purpose of this part of IEC 63132 is to establish, in a general way, suitable procedures and
tolerances for the installation of hydroelectric turbines and generators. This document presents
a typical assembly. There are many possible ways to assemble a unit. The size of the machines,
design of the machines, layout of the powerhouse and delivery schedule of the components are
some of the elements that could result in additional steps, the elimination of some steps and/or
assembly sequences.
It is understood that a publication of this type will be binding only if, and to the extent that, both
contracting parties have agreed upon it.
Installations for refurbishment projects or for small hydro projects are not in the scope of this
document. An agreement between all parties is necessary.
This document excludes matters of purely commercial interest, except those inextricably bound
up with the conduct of installation.
The tolerances in this document have been established upon best practices and experience,
although it is recognized that other standards specify different tolerances.
Wherever this document specifies that documents, drawings or information is supplied by a
manufacturer (or manufacturers), each individual manufacturer will furnish the appropriate
information for their own supply only.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60193:2019(Main)
Hydraulic turbines, storage pumps and pump-turbines - Model acceptance tests (IEC 60193:2019)
EN IEC 60193:2019

This document applies to laboratory models of any type of impulse or reaction hydraulic turbine,
storage pump or pump-turbine.
This document applies to models of prototype machines either with unit power greater than
5 MW or with reference diameter greater than 3 m. Full application of the procedures herein
prescribed is not generally justified for machines with smaller power and size. Nevertheless,
this document may be used for such machines by agreement between the purchaser and the
supplier.
In this document, the term "turbine" includes a pump-turbine operating as a turbine and the
term "pump" includes a pump-turbine operating as a pump.
This document excludes all matters of purely commercial interest, except those inextricably
bound up with the conduct of the tests.
This document is concerned with neither the structural details of the machines nor the
mechanical properties of their components, so long as these do not affect model performance
or the relationship between model and prototype performances.
This document covers the arrangements for model acceptance tests to be performed on
hydraulic turbines, storage pumps and pump-turbines to determine if the main hydraulic
performance contract guarantees (see 4.2) have been satisfied.
It contains the rules governing test conduct and prescribes measures to be taken if any phase
of the tests is disputed.
The main objectives of this document are:
– to define the terms and quantities used;
– to specify methods of testing and of measuring the quantities involved, in order to ascertain
the hydraulic performance of the model;
– to specify the methods of computation of results and of comparison with guarantees;
– to determine if the contract guarantees that fall within the scope of this document have been
fulfilled;
– to define the extent, content and structure of the final report.
The guarantees can be given in one of the following ways:
– guarantees for prototype hydraulic performance, computed from model test results
considering scale effects;
– guarantees for model hydraulic performance.
Moreover, additional performance data (see 4.4) can be needed for the design or the operation
of the prototype of the hydraulic machine. Contrary to the requirements of Clauses 4 to 6 related
to main hydraulic performance, the information of these additional data given in Clause 7 is
considered only as recommendation or guidance to the user (see 7.1).
It is particularly recommended that model acceptance tests be performed if the expected field
conditions for acceptance tests (see IEC 60041:1991) would not allow the verification of
guarantees given for the prototype machine.
A transposition method taking into account the model and prototype wall surface roughness for
the performance conversion on pump-turbines, Francis turbines, and axial machines is
described in IEC 62097. This method requires model and prototype surface roughness data and
is takes into account the shift in nED, QED and PED factors for determining the transposition of
efficiency between model and prototype. However, in the case of Francis machines with semispiral
casing and axial machines, the transposition method has not been fully validated due to
a lack of data. In addition, IEC 62097 does not apply to storage pumps, Pelton turbines, and
Dériaz. Therefore, for these and otherwise specifically agreed upon cases where hydraulically
smooth flow conditions are assumed on the model and the prototype, the transposition formula
and procedure given in Annex D and Annex I can be applied. Applications and limitations of
both this document and IEC 62097 transposition methods are discussed in Annex E.
The method for performance conversion from model to prototype needs to be clearly defined in
the main hydraulic performance contract.

  • Standard
    314 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62097:2019(Amendment)
Hydraulic machines, radial and axial - Methodology for performance transposition from model to prototype (IEC 62097:2019)
EN IEC 62097:2019

This International Standard establishes the prototype hydraulic machine efficiency from model
test results, with consideration of scale effect including the effect of surface roughness.
This document is intended to be used for the assessment of the results of contractual model
tests of hydraulic machines.

  • Standard
    129 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62364:2019(Main)
Hydraulic machines - Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines (IEC 62364:2019)
EN IEC 62364:2019

This document gives guidelines for:
a) presenting data on hydro-abrasive erosion rates on several combinations of water quality, operating conditions, component materials, and component properties collected from a variety of hydro sites;
b) developing guidelines for the methods of minimizing hydro-abrasive erosion by modifications to hydraulic design for clean water. These guidelines do not include details such as hydraulic profile shapes which are determined by the hydraulic design experts for a given site;
c) developing guidelines based on “experience data” concerning the relative resistance of materials faced with hydro-abrasive erosion problems;
d) developing guidelines concerning the maintainability of materials with high resistance to hydro-abrasive erosion and hardcoatings;
e) developing guidelines on a recommended approach, which owners could and should take to ensure that specifications communicate the need for particular attention to this aspect of hydraulic design at their sites without establishing criteria which cannot be satisfied because the means are beyond the control of the manufacturers;
f) developing guidelines concerning operation mode of the hydro turbines in water with particle materials to increase the operation life.
It is assumed in this document that the water is not chemically aggressive. Since chemical aggressiveness is dependent upon so many possible chemical compositions, and the materials of the machine, it is beyond the scope of this document to address these issues.
It is assumed in this document that cavitation is not present in the turbine. Cavitation and hydro-abrasive erosion can reinforce each other so that the resulting erosion is larger than the sum of cavitation erosion plus hydro-abrasive erosion. The quantitative relationship of the resulting hydro-abrasive erosion is not known and it is beyond the scope of this document to assess it, except to suggest that special efforts be made in the turbine design phase to minimize cavitation.
Large solids (e.g. stones, wood, ice, metal objects, etc.) traveling with the water can impact turbine components and produce damage. This damage can in turn increase the flow turbulence thereby accelerating wear by both cavitation and hydro-abrasive erosion. Hydroabrasive erosion resistant coatings can also be damaged locally by impact of large solids. It isbeyond the scope of this document  to address these issues.
This document focuses mainly on hydroelectric powerplant equipment. Certain portions can
also be applicable to other hydraulic machines.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62256:2017(Main)
Hydraulic turbines, storage pumps and pump-turbines - Rehabilitation and performance improvement (IEC 62256:2017)
EN 62256:2017

This document covers turbines, storage pumps and pump-turbines of all sizes and of the
following types:
• Francis;
• Kaplan;
• propeller;
• Pelton (turbines only);
• bulb turbines.
This document also identifies without detailed discussion, other powerhouse equipment that
could affect or be affected by a turbine, storage pump, or pump-turbine rehabilitation.
The object of this document is to assist in identifying, evaluating and executing rehabilitation
and performance improvement projects for hydraulic turbines, storage pumps and pumpturbines.
This document can be used by owners, consultants, and suppliers to define:
• needs and economics for rehabilitation and performance improvement;
• scope of work;
• specifications;
• evaluation of results.
This document is intended to be:
• an aid in the decision process;
• an extensive source of information on rehabilitation;
• an identification of the key milestones in the rehabilitation process;
• an identification of the points to be addressed in the decision processes.
This document is not intended to be a detailed engineering manual nor a maintenance
document.

  • Standard
    160 pages
    English language
    sale 10% off
    e-Library read for
    1 day