SIST ISO 12635:1997
(Main)Graphic technology -- Plates for offset printing -- Dimensions
Graphic technology -- Plates for offset printing -- Dimensions
Technologie graphique -- Plaques pour impression offset -- Dimensions
Grafična tehnologija - Plošče za ofsetni tisk - Mere
General Information
Relations
Standards Content (Sample)
INTERNATIONAL
STANDARD
First edition
1996-07-o 1
Graphic technology - Plates for offset
printing - Dimensions
Technologie graphique - Plaques pour impression offset - Dimensions
Reference number
IS0 12635:1996(E)
---------------------- Page: 1 ----------------------
reword
IS0 (the International Organization for Standardization) is a worldwide fed-
eration of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be rep-
resented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. IS0 col-
laborates closely with the International Electrotechnical Commission (IEC)
on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are cir-
culated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 12635 was prepared by Technical Committee
ISOnC 130, Graphic technology.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be repro-
duced or utilized in any form or by any means, electronic or mechanical, including photo-
copying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 2 ----------------------
Q IS0
IS0 12635:1996(E)
Introduction
This International Standard is a first step towards stipulating the properties
of printing plates for offset printing. While not all existing plate sizes are
covered by this International Standard, the stipulations on dimensions and
the recommendation of only three types of perforation are aimed at limit-
ing the existing wide range, and simplifying manufacture and communi-
cations between plate manufacturers, press manufacturers and printing
houses.
. . .
III
---------------------- Page: 3 ----------------------
This page intentionally left blank
---------------------- Page: 4 ----------------------
IS0 12635:1996(E)
INTERNATIONAL STANDARD @ IS0
Plates for offset printing -
Graphic technology -
Dimensions
3.3 plate thickness (s): Nominal caliper of a coated
1 Scope
plate.
This International Standard specifies the width, length,
and labelling
thickness, perforation, designation
(marking) of printing plates (referred to hereafter as
4 Requirements
“plates”) for offset printing. It is intended to facilitate
4.1 Measurement
better communication between plate manufacturers, conditions
press manufacturers and printing houses.
Measurements shall
be conducted under standard
The specifications given in this International Standard atmosphere for conditioning as specified in IS0 554.
are intended primarily for metal plates. However, this
International Standard may apply to other materials if 4.2 Dimensions
they meet the requirements of clause 4. It is not in-
tended for material supplied in rolled form. 4.21 Plate dimensions
The nominal plate width, plate length and plate thick-
ness shall be as specified in tables 1 and 2 when
2 Normative reference
measured under the conditions specified in 4.1.
The following standard contains provisions which,
The length and width tolerances shown in table 1 are
through reference in this text, constitute provisions of
based on a perfectly rectangular plate. Figure 1 shows
this International Standard. At the time of publication,
the nominal dimensions of a plate (solid line) together
the edition indicated was valid. All standards are sub-
with rectangles corresponding to plus and minus tol-
ject to revision, and parties to agreements based on
erances (dashed lines). The actual contour of the plate
this International Standard are encouraged to investi-
including deviations from rectangularity shall cover the
gate the possibility of applying the most recent edition
smaller rectangle at all points but shall not extend
...
SLOVENSKI STANDARD
SIST ISO 12635:1997
01-december-1997
*UDILþQDWHKQRORJLMD3ORãþH]DRIVHWQLWLVN0HUH
Graphic technology -- Plates for offset printing -- Dimensions
Technologie graphique -- Plaques pour impression offset -- Dimensions
Ta slovenski standard je istoveten z: ISO 12635:1996
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
SIST ISO 12635:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 12635:1997
---------------------- Page: 2 ----------------------
SIST ISO 12635:1997
INTERNATIONAL
STANDARD
First edition
1996-07-o 1
Graphic technology - Plates for offset
printing - Dimensions
Technologie graphique - Plaques pour impression offset - Dimensions
Reference number
IS0 12635:1996(E)
---------------------- Page: 3 ----------------------
SIST ISO 12635:1997
reword
IS0 (the International Organization for Standardization) is a worldwide fed-
eration of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be rep-
resented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. IS0 col-
laborates closely with the International Electrotechnical Commission (IEC)
on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are cir-
culated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 12635 was prepared by Technical Committee
ISOnC 130, Graphic technology.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be repro-
duced or utilized in any form or by any means, electronic or mechanical, including photo-
copying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 4 ----------------------
SIST ISO 12635:1997
Q IS0
IS0 12635:1996(E)
Introduction
This International Standard is a first step towards stipulating the properties
of printing plates for offset printing. While not all existing plate sizes are
covered by this International Standard, the stipulations on dimensions and
the recommendation of only three types of perforation are aimed at limit-
ing the existing wide range, and simplifying manufacture and communi-
cations between plate manufacturers, press manufacturers and printing
houses.
. . .
III
---------------------- Page: 5 ----------------------
SIST ISO 12635:1997
This page intentionally left blank
---------------------- Page: 6 ----------------------
SIST ISO 12635:1997
IS0 12635:1996(E)
INTERNATIONAL STANDARD @ IS0
Plates for offset printing -
Graphic technology -
Dimensions
3.3 plate thickness (s): Nominal caliper of a coated
1 Scope
plate.
This International Standard specifies the width, length,
and labelling
thickness, perforation, designation
(marking) of printing plates (referred to hereafter as
4 Requirements
“plates”) for offset printing. It is intended to facilitate
4.1 Measurement
better communication between plate manufacturers, conditions
press manufacturers and printing houses.
Measurements shall
be conducted under standard
The specifications given in this International Standard atmosphere for conditioning as specified in IS0 554.
are intended primarily for metal plates. However, this
International Standard may apply to other materials if 4.2 Dimensions
they meet the requirements of clause 4. It is not in-
tended for material supplied in rolled form. 4.21 Plate dimensions
The nominal plate width, plate length and plate thick-
ness shall be as specified in tables 1 and 2 when
2 Normative reference
measured under the conditions specified in 4.1.
The following standard contains provisions which,
The length and width tolerances shown in table 1 are
through reference in this text, constitute provisions of
based on a perfectly rectangul
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.