Bitumen and bituminous binders - Determination of needle penetration

This document specifies a method for determining the consistency of bitumen and bituminous binders. The normal procedure is described for penetrations up to 330 mm × 0,1 mm at 25 °C. The maximum penetration that can be tested is 500 mm × 0,1 mm.
WARNING The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der Nadelpenetration

Dieses Dokument legt ein Verfahren zur Bestimmung der Konsistenz von Bitumen und bitumenhaltigen Binde¬mitteln fest. Das übliche Verfahren wird für Penetrationen bis zu 330 mm × 0,1 mm bei 25 °C beschrieben. Die maximale Penetration, die geprüft werden kann, beträgt 500 mm × 0,1 mm.
WARNUNG Die Anwendung dieses Dokumentes kann den Einsatz gefährlicher Stoffe, Arbeitsgänge und Geräte bedingen. Dieses Dokument erhebt nicht den Anspruch, alle mit ihrer Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieses Dokuments, geeignete Sicherheits- und Gesundheitsschutzmaßnahmen vorzusehen und im Vorfeld die Anwendbarkeit von einschränkenden Vorschriften zu klären.

Bitumes et liants bitumineux - Détermination de la pénétrabilité à l'aiguille

Le présent document prescrit une méthode pour la détermination de la consistance des bitumes et des liants bitumineux. Le mode opératoire s'applique normalement pour les pénétrabilités inférieures ou égales à 330 × 0,1 mm à 25 °C. La pénétrabilité maximale qu'il est possible de mesurer est de 500 × 0,1 mm.
AVERTISSEMENT L'utilisation de ce document implique l'usage de produits, d'opérations et d'équipements à caractère dangereux. Le présent document n'est pas censé aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de son utilisateur d'établir des règles d'hygiène et de sécurité appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določanje penetracije z iglo

General Information

Status
Not Published
Public Enquiry End Date
29-Jun-2023
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
27-Jun-2024
Due Date
15-Aug-2024

Relations

Buy Standard

Draft
prEN 1426:2023
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 1426:2023
01-junij-2023
Bitumen in bitumenska veziva - Določanje penetracije z iglo
Bitumen and bituminous binders - Determination of needle penetration
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Nadelpenetration
Bitumes et liants bitumineux - Détermination de la pénétrabilité à l'aiguille
Ta slovenski standard je istoveten z: prEN 1426
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 1426:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1426:2023

---------------------- Page: 2 ----------------------
oSIST prEN 1426:2023


DRAFT
EUROPEAN STANDARD
prEN 1426
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2023
ICS 75.140; 91.100.50 Will supersede EN 1426:2015
English Version

Bitumen and bituminous binders - Determination of
needle penetration
Bitumes et liants bitumineux - Détermination de la Bitumen und bitumenhaltige Bindemittel -
pénétrabilité à l'aiguille Bestimmung der Nadelpenetration
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1426:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1426:2023
prEN 1426:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 6
6 Sampling . 9
7 Procedure.10
7.1 Preparation of the needle holder and needles .10
7.2 Tests in the constant temperature bath.10
7.3 Tests outside the constant temperature bath .10
7.4 Determination of the penetration .11
7.4.1 First determinations .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.