SIST EN 3999:2007

Aerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm <= a <= 6 mm

This standard specifies the requirements relating to:
Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm This material is manufactured to a minimum residual stress requirement for chemical milling applications.

Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T351 - Bleche und Bänder mit besserer Eignung zum chemischen Fräsen 1,6 mm <= a <= 6 mm

Série aérospatiale - Alliage d'aluminium AL-P2024-T351 - Tôles et bandes avec aptitude améliorée a l'usinage chimique 1,6 mm <= a <= 6 mm

Aeronavtika - Aluminijeva zlitina AL-P2024-T351 - Pločevina in trakovi z izboljšanimi lastnostmi za kemično rezkanje 1,6 mm <= a <= 6 mm

General Information

• Status: Published
• Publication Date: 01-Oct-2007
• ICS: 49.025.20 - Aluminium
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 03-Sep-2007
• Due Date: 08-Nov-2007
• Completion Date: 02-Oct-2007
• Ref Project: EN 3999:2007 - Aerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm ≤ a ≤ 6 mm

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T351 - Bleche und Bänder mit besserer Eignung zum chemischen Fräsen 1,6 mm <= a <= 6 mmSérie aérospatiale - Alliage d'aluminium AL-P2024-T351 - Tôles et bandes avec aptitude améliorée a l'usinage chimique 1,6 mm <= a <= 6 mmAerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm <= a <= 6 mm49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 3999:2007SIST EN 3999:2007en01-november-2007SIST EN 3999:2007SLOVENSKI
STANDARD



SIST EN 3999:2007



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3999
August 2007 ICS 77.150.10 English Version
Aerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm ≤ a ≤ 6 mm
Série aérospatiale - Alliage d'aluminium AL-P2024-T351 - Tôles et bandes avec aptitude améliorée à l'usinage chimique 1,6 mm ≤ a ≤ 6 mm
Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T351 - Bleche und Bänder mit besserer Eignung zum chemischen Fräsen 1,6 mm ≤ a ≤ 6 mm This European Standard was approved by CEN on 12 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3999:2007: ESIST EN 3999:2007



EN 3999:2007 (E) 2 Contents Foreword.3 Introduction.4 1 Scope.4 2 Normative references.4
SIST EN 3999:2007



EN 3999:2007 (E) 3 Foreword This document (EN 3999:2007) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn at the latest by February 2008. According to the
...