SIST-TS CEN/TS 1852-2:2009
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
This Technical Specification gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system. This Technical Specification includes: a) requirements for materials, components, joints and assemblies given in EN 1852-1; b) requirements for the manufacturer's quality system; c) definitions and procedures to be applied if third party certification is involved.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität, die als Teil des
Qualitätssicherungssystems im Qualitätssicherungsplan des Herstellers enthalten sein müssen.
Diese Technische Spezifikation enthält:
a) Anforderungen an Werkstoffe, Rohrleitungsteile, Verbindungen und Bauteilkombinationen, die in
EN 1852-1 festgelegt sind;
b) Anforderungen an das Qualitätssicherungssystem des Herstellers;
ANMERKUNG 1 Das Qualitätssicherungssystem sollte EN ISO 9001:2008 [1] entsprechen.
c) Definitionen und Verfahren im Falle der Zertifizierung durch unparteiische Dritte.
ANMERKUNG 2 Bei Drittstellenzertifizierung wird empfohlen, diese durch eine, in Abhängigkeit der Anwendung, nach
EN 45011:1998 [2] bzw. EN ISO 17021:2006 [3] zugelassene Zertifizierungsstelle durchführen zu lassen.
1.2 Anwendung
Diese Technische Spezifikation gilt für erdverlegte drucklose Abwasserkanäle und -leitungen aus Polypropylen
(PP):
a) die für Anwendungen außerhalb der Gebäudestruktur vorgesehen sind; auf dem Erzeugnis gekennzeichnet
durch Anwendungskennzeichen „U“; und
b) die für Anwendungen sowohl außerhalb (Anwendungskennzeichen „U“) als auch innerhalb (Anwendungskennzeichen
„D“) der Gebäudestruktur vorgesehen sind; auf dem Erzeugnis gekennzeichnet durch „UD“.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement sans pression enterrés - Polypropylène (PP) - Partie 2 : Guide d'évaluation de la conformité
1.1 Généralités
La présente spécification technique indique comment inclure l’évaluation de conformité dans le plan qualité du
fabricant dans le cadre du système qualité.
Elle comporte les points suivants :
a) exigences relatives aux matières, composants, joints et assemblages énoncées dans l’EN 1852-1 ;
b) exigences relatives au système qualité du fabricant ;
NOTE 1 Il est recommandé que le système qualité soit conforme à l’EN ISO 9001:2008 [1].
c) définitions et modes opératoires à appliquer en cas de certification par tierce partie.
NOTE 2 Si une certification par tierce partie est prévue, il est recommandé que l’organisme de certification soit
accrédité selon l’EN 45011:1998 [2] ou l’EN ISO/CEI 17021:2006 [3], selon le cas.
1.2 Applicabilité
La présente spécification technique s’applique aux systèmes de canalisations en polypropylène (PP) destinés
à être utilisés pour :
a) les branchements et les collecteurs d’assainissement sans pression enterrés à l’extérieur de la structure
du bâtiment (code de zone d’application «U»), ce qui se traduit dans le marquage des produits par le
code «U», et
b) les branchements et les collecteurs d’assainissement sans pression enterrés aussi bien à l’intérieur (code
de zone d’application «D») qu’à l’extérieur de la structure du bâtiment (code de zone d’application «U»),
ce qui se traduit dans le marquage des produits par le code «UD».
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 2. del: Navodilo za ugotavljanje skladnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 1852-2:2009
01-oktober-2009
1DGRPHãþD
SIST ENV 1852-2:2001
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 2. del:
Navodilo za ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement sans pression enterrés - Polypropylène (PP) - Partie 2 : Guide
d'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 1852-2:2009
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST-TS CEN/TS 1852-2:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 1852-2:2009
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 1852-2:2009
TECHNICAL SPECIFICATION
CEN/TS 1852-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2009
ICS 23.040.01; 93.030 Supersedes ENV 1852-2:2000
English Version
Plastics piping systems for non-pressure underground drainage
and sewerage - Polypropylene (PP) - Part 2: Guidance for the
assessment of conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte drucklose
branchements et les collecteurs d'assainissement sans Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil
pression enterrés - Polypropylène (PP) - Partie 2 : Guide 2: Empfehlungen für die Beurteilung der Konformität
d'évaluation de la conformité
This Technical Specification (CEN/TS) was approved by CEN on 10 December 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1852-2:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
Contents Page
Foreword . 3
Introduction . 4
1 Scope . 5
1.1 General . 5
1.2 Applicability . 5
2 Normative references . 5
3 Definitions, symbols and abbreviations . 5
3.1 Definitions . 5
3.2 Abbreviations . 7
4 Requirements . 8
4.1 General . 8
4.2 Testing and inspection . 8
4.2.1 Material specification . 8
4.2.2 Grouping . 8
4.2.3 Type tests (TT) . 9
4.2.4 Batch release tests (BRT) . 12
4.2.5 Process verification tests (PVT) . 13
4.2.6 Audit tests (AT) . 14
4.2.7 Indirect tests (IT) . 15
4.2.8 Inspection records and test records . 16
Bibliography . 17
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
Foreword
This document (CEN/TS 1852-2:2009) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This document supersedes ENV 1852-2:2000.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
System Standards are based on the results of the work undertaken in ISO/TC 138 "Plastics pipes, fittings and
valves for the transport of fluids", which is a Technical Committee of the International Organization for
Standardization (ISO).
They are supported by separate standards on test methods to which references are made throughout the
System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 1852 consists of the following Parts, under the general title Plastics piping systems for non-pressure
underground drainage and sewerage - Polypropylene (PP)
Part 1: Specifications for pipes, fittings and the system
Part 2: Guidance for the assessment of conformity (the present Technical Specification)
Part 3: Guidance for installation (Technical Specification)
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
Introduction
This Technical Specification is intended to serve as a guide for the assessment of conformity of products
covered by EN 1852-1.
It can be used integrally and/or be used for inclusion of conformity assessment in the manufacturer's quality
plan as part of the quality system for attestation purposes. The use of this Technical Specification does not
necessarily imply the involvement of a third party.
It can also be used to support the elaboration of national third party certification procedures for products
conforming to EN 1852-1. It is the responsibility of the manufacturer to choose or not to choose for the
involvement of a third party for certification purposes.
4
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
1 Scope
1.1 General
This Technical Specification gives guidance for the assessment of conformity to be included in the
manufacturer's quality plan as part of the quality system.
This Technical Specification includes:
a) requirements for materials, components, joints and assemblies given in EN 1852-1;
b) requirements for the manufacturer's quality system;
[1]
NOTE 1 It is recommended that the quality system conforms to EN ISO 9001:2008 .
c) definitions and procedures to be applied if third party certification is involved.
NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to
[2] [3]
EN 45011:1998 or EN ISO/IEC 17021:2006 , as applicable.
1.2 Applicability
This Technical Specification is applicable to piping systems made of polypropylene (PP) intended to be used
for:
a) non-pressure underground drainage and sewerage outside the building structure (application area code
"U"), reflected in the marking of products by "U", and
b) for non-pressure underground drainage and sewerage for both buried in the ground within the building
structure (application area code "D") and outside the building structure (application area code "U"),
reflected in the marking of products by "UD".
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 1852-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
3 Definitions, symbols and abbreviations
For the purposes of this Technical Specification, the definitions, symbols and abbreviations given in
EN 1852-1:2009, together with the following apply.
3.1 Definitions
3.1.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and responsibility
to carry out certification of conformity according to given rules of procedure and management
5
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
3.1.2
inspection body
impartial organisation or company, approved by the certification body as possessing the necessary
competence to verify and/to carry out initial type testing, audit testing and inspection of the manufacturer's
factory production control in accordance with the relevant European Standard
3.1.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of
materials and products
3.1.4
quality system
organisational structure, responsibilities, procedures, processes and resources for implementing quality
[4]
management (see EN ISO 9000:2005 )
3.1.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.1.6
modes of type testing
3.1.6.1
type testing (TT)
testing performed to prove that the material, component, joint or assembly is capable of conforming to the
requirements given in the relevant standard
3.1.6.2
preliminary type testing (PTT)
type testing carried out by or on behalf of the manufacturer
3.1.6.3
initial type testing (ITT)
type testing carried out by or on behalf of the certification body for certification purposes
3.1.7
batch release test (BRT)
test performed by the manufacturer on a batch of components, which has to be satisfactorily completed before
the batch can be released
3.1.8
process verification test (PVT)
test performed by the manufacturer on materials, components, joints or assemblies at specific intervals to
confirm that the process continues to be capable of producing components conforming to the requirements
given in the relevant standard
NOTE Such tests are not required to release batches of components and are carried out as a measure of process
control.
3.1.9
audit test (AT)
test performed by or on behalf of a certification body to confirm that the material, component, joint or assembly
continues to conform with the requirements given in the relevant standard and to provide information to
assess the effectiveness of the quality system
6
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
3.1.10
indirect test (IT)
test performed by the manufacturer different from that specified for that particular characteristic, having
verified its correlation with the specified test
3.1.11
witness testing (WT)
testing accepted by a certification body for initial type testing and/or audit testing, which is carried out by, or on
behalf of the manufacturer and supervised by a representative of the certification body, qualified in testing
3.1.12
material
defined type of polymer or additive or constituent thereof
3.1.13
compound (blend)
recipe that defines types of polymer, additives and constituents at specified dosage levels
3.1.14
material batch or compound batch
clearly identifiable quantity of a particular material or compound
3.1.15
production batch
clearly identifiable collection of units, manufactured consecutively under the same conditions, using material
or compounds conforming to the same specification
3.1.16
lot
clearly identifiable subdivision of a batch for inspection purposes
3.1.17
sample
one or more units of product drawn from a batch or lot, selected at random without regard to quality
NOTE The number of units of product in the sample is the sample size.
3.1.18
group
collection of similar components from which samples are selected for testing purposes
3.2 Abbreviations
NOTE For reasons to avoid misunderstanding the following abbreviations are kept the same for each language. For
the same reason, the terms are given in three languages ("en" for English, "fr" for French and "de" for German).
AT en : audit test
fr : essai d'audit
de : Überwachungsprüfung
BRT en : batch release test
fr : essai de libération de campagne de fabrication
de : Freigabeprüfung einer Charge
7
---------------------- Page: 9 ----------------------
SIST-TS CEN/TS 1852-2:2009
CEN/TS 1852-2:2009 (E)
IT en : indirect test
fr : essai indirect
de : indirekte Prüfung
ITT en : initial type testing
fr : essais de type initiaux
de : Erst-Typprüfung
PTT en : preliminary type testing
fr : essais de type préliminaires
de : vorausgehende Typprüfung
PVT en : process verification testing
fr : essai de vérification du procédé de fabrication
de : Prozessüberprüfung
TT en : type test
fr : essai de type
de : Typprüfung
WT en : witness testing
fr : essais de témoins
de : Prüfung unter Aufsicht
4 Requirements
4.1 General
4.1.1 Materials, components, joints and assemblies shall conform to the requirements given in EN 1852-1.
4.1.2 Components
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.