SIST EN 300 443-5 V1.2.1:2003
(Main)Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3 specification for basic call/bearer control; Part 5: Test Suite Structure and Test Purposes (TSS&TP) specification for the network
Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3 specification for basic call/bearer control; Part 5: Test Suite Structure and Test Purposes (TSS&TP) specification for the network
Upgrade of Tset Specification.
Širokopasovno digitalno omrežje z integriranimi storitvami (B-ISDN) – Protokol digitalne naročniške signalizacije št. 2 (DSS2) – Specifikacija tretje plasti vmesnika uporabnik-omrežje B-ISDN za krmiljenje osnovnega klica/nosilca – 5. del: Zgradba preskušalnega niza in nameni preskušanja (TSS&TP) – Specifikacija za omrežje
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2003
âLURNRSDVRYQRGLJLWDOQRRPUHåMH]LQWHJULUDQLPLVWRULWYDPL %,6'1 ±3URWRNRO
GLJLWDOQHQDURþQLãNHVLJQDOL]DFLMHãW '66 ±6SHFLILNDFLMDWUHWMHSODVWLYPHVQLND
XSRUDEQLNRPUHåMH%,6'1]DNUPLOMHQMHRVQRYQHJDNOLFDQRVLOFD±GHO =JUDGED
SUHVNXãDOQHJDQL]DLQQDPHQLSUHVNXãDQMD 766 73 ±6SHFLILNDFLMD]DRPUHåMH
Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling
System No. two (DSS2) protocol; B-ISDN user-network interface layer 3 specification for
basic call/bearer control; Part 5: Test Suite Structure and Test Purposes (TSS&TP)
specification for the network
Ta slovenski standard je istoveten z: EN 300 443-5 Version 1.2.1
ICS:
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
European Standard (Telecommunications series)
Broadband Integrated Services Digital Network (B-ISDN);
Digital Subscriber Signalling System No. two (DSS2) protocol;
B-ISDN user-network interface layer 3 specification
for basic call/bearer control;
Part 5: Test Suite Structure and Test Purposes (TSS&TP)
specification for the network
2 ETSI EN 300 443-5 V1.2.1 (2000-10)
Reference
REN/SPAN-05143-5
Keywords
BC, B-ISDN, broadband, DSS2, ISDN, layer 3,
network, TSS&TP, UNI
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.:+33492944200 Fax:+33 493654716
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at http://www.etsi.org/tb/status/
If you find errors in the present document, send your comment to:
editor@etsi.fr
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2000.
All rights reserved.
ETSI
3 ETSI EN 300 443-5 V1.2.1 (2000-10)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope .6
2 References .6
3 Definitions and abbreviations.6
3.1 Definitions.6
3.1.1 Definitions related to conformance testing .6
3.1.2 Definitions related to EN 300 443-1.7
3.2 Abbreviations .7
4 Test Suite Structure (TSS).8
5 Test Purposes (TP) .9
5.1 Introduction .9
5.1.1 TP naming convention.9
5.1.2 Source of TP definition.9
5.1.3 Test strategy.9
5.1.4 Test of call states .9
5.2 TPs for the basic call/bearer control, layer 3, network .10
5.2.1 Signalling procedures at the coincident S /T and at the T reference points.10
B B B
5.2.1.1 Call/connection establishment at the originating interface.10
5.2.1.1.1 Connection identifier (VPCI/VCI) allocation/selection (01).10
5.2.1.1.1.1 Associated signalling (02).10
5.2.1.1.1.2 Non-associated signalling (03).11
5.2.1.1.2 QOS and traffic parameter selection procedures (04).12
5.2.1.1.3 Invalid call/connection control information (05).12
5.2.1.1.4 Call/connection proceeding (06).12
5.2.1.1.5 Call/connection confirmation indication (07).13
5.2.1.1.6 Call/connection acceptance (08).13
5.2.1.1.7 Call/connection rejection (09) .13
5.2.1.1.8 Transit network selection (10).14
5.2.1.2 Call/connection establishment at the destination interface.14
5.2.1.2.1 Incoming call/connection request (11) .14
5.2.1.2.2 Connection identifier (VPCI/VCI) allocation/selection (12).15
5.2.1.2.2.1 Associated signalling (13).15
5.2.1.2.2.2 Non-associated signalling (14).15
5.2.1.2.3 Call/connection confirmation (15).16
5.2.1.2.4 Call/connection acceptance (16).17
5.2.1.3 Call/connection clearing.17
5.2.1.3.1 Exception conditions (17).17
5.2.1.3.2 Clearing initiated by the user (18) .17
5.2.1.3.3 Clearing initiated by the network (19).18
5.2.1.3.4 Clear collision (20).18
5.2.1.4 Restart procedure .19
5.2.1.4.1 Sending RESTART (21).19
5.2.1.4.2 Receipt of RESTART (22) .19
5.2.1.4.3 Remote interface (23).22
5.2.1.5 Handling of error conditions .22
5.2.1.5.1 Error handling in N0 (24) .22
5.2.1.5.2 Error handling in N3 (25) .26
5.2.1.5.3 Error handling in N4 (26) .27
5.2.1.5.4 Error handling in N6 (27) .29
5.2.1.5.5 Error handling in N7 (28) .32
5.2.1.5.6 Error handling in N9 (29) .34
5.2.1.5.7 Error handling in N10 - incoming call (30) .37
ETSI
4 ETSI EN 300 443-5 V1.2.1 (2000-10)
5.2.1.5.8 Error handling in N10 - outgoing call (31).40
5.2.1.5.9 Error handling in N12 - incoming call (32) .44
5.2.1.5.10 Error handling in N12 - outgoing call (33).46
5.2.1.5.11 Error handling in R0 (34) .48
5.2.1.5.12 Error handling in R1 (35) .51
5.2.1.6 Notification procedures (36) .53
5.2.2 Signalling procedures for interworking between N-ISDN and B-ISDN.54
5.2.2.1 Interworking N-ISDN -> B-ISDN (37).54
5.2.2.2 Interworking B-ISDN -> N-ISDN (38).54
6 Compliance.55
7 Requirements for a comprehensive testing service .55
Bibliography.56
History .57
ETSI
5 ETSI EN 300 443-5 V1.2.1 (2000-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://www.etsi.org/ipr).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services and
Protocols for Advanced Networks (SPAN).
The present document is part 5 of a multi-part standard covering the Digital Subscriber Signalling System No. 2 (DSS2)
protocol specification for the B-ISDN user-network interface layer 3 specification for basic call/bearer control, as
described below:
Part 1: "Protocol specification";
Part 2: "Protocol Implementation Conformance Statement (PICS) proforma specification";
Part 3: "Test Suite Structure and Test Purposes (TSS&TP) specification for the user";
Part 4: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification for the user";
Part 5: "Test Suite Structure and Test Purposes (TSS&TP) specification for the network";
Part 6: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification for the network".
National transposition dates
Date of adoption of this EN: 6 October 2000
Date of latest announcement of this EN (doa): 31 January 2001
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2001
Date of withdrawal of any conflicting National Standard (dow): 31 July 2001
ETSI
6 ETSI EN 300 443-5 V1.2.1 (2000-10)
1 Scope
The present document specifies the network Test Suite Structure and Test Purposes (TSS&TP) for the T reference
B
point or coincident S and T reference point (as defined in ITU-T Recommendation I.413 [5]) of implementations
B B
conforming to the standards for the signalling user-network layer 3 specification for basic call/bearer control of the
Digital Subscriber Signalling System No. two (DSS2) protocol for the pan-European Broadband Integrated Services
Digital Network (B-ISDN), EN 300 443-1 [1].
A further part of the present document specifies the Abstract Test Suite (ATS) and partial Protocol Implementation
eXtra Information for Testing (PIXIT) proforma based on the present document.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
• A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same
number.
[1] ETSI EN 300 443-1 (V1.3): "Broadband Integrated Services Digital Network (B-ISDN); Digital
Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3
specification for basic call/bearer control; Part 1: Protocol specification [ITU-T Recommendation
Q.2931 (1995), modified]".
[2] ETSI EN 300 443-2 (V1.3): "Broadband Integrated Services Digital Network (B-ISDN); Digital
Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3
specification for basic call/bearer control; Part 2: Protocol Implementation Conformance
Statement (PICS) proforma specification".
[3] ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 1: General concepts".
[4] ISO/IEC 9646-2: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 2: Abstract Test Suite specification".
[5] ITU-T Recommendation I.413 (1993): "B-ISDN user-network interface".
[6] ETSI ETS 300 406: "Methods for Testing and Specification (MTS); Protocol and profile
conformance testing specifications; Standardization methodology".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in EN 300 443-1 [1] and the following apply:
3.1.1 Definitions related to conformance testing
abstract test case: refer to ISO/IEC 9646-1 [3]
ETSI
7 ETSI EN 300 443-5 V1.2.1 (2000-10)
Abstract Test Method (ATM): refer to ISO/IEC 9646-1 [3]
Abstract Test Suite (ATS): refer to ISO/IEC 9646-1 [3]
Implementation Under Test (IUT): refer to ISO/IEC 9646-1 [3]
lower tester: refer to ISO/IEC 9646-1 [3]
Protocol Implementation Conformance Statement (PICS): refer to ISO/IEC 9646-1 [3]
PICS proforma: refer to ISO/IEC 9646-1 [3]
Protocol Implementation eXtra Information for Testing (PIXIT): refer to ISO/IEC 9646-1 [3]
PIXIT proforma: refer to ISO/IEC 9646-1 [3]
Test Purpose (TP): refer to ISO/IEC 9646-1 [3]
3.1.2 Definitions related to EN 300 443-1
network: DSS2 protocol entity at the Network side of the user-network interface where a T reference point or
B
coincident S and T reference point applies
B B
network (S /T ): DSS2 protocol entity at the Network side of the user-network interface where a coincident S and T
B B B B
reference point applies
network (T ): DSS2 protocol entity at the Network side of the user-network interface where a T reference point
B B
applies (user is the private ISDN)
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ATM Abstract Test Method
ATS Abstract Test Suite
B-ISDN Broadband Integrated Services Digital Network
DSS2 Digital Subscriber Signalling System No. two
IUT Implementation Under Test
N0 Null call state
N1 Call Initiated call state
N10 Active call state
N12 Release Indication call state
N2 Overlap Sending call state
N3 Outgoing Call Proceeding call state
N4 Call Delivered call state
N6 Call Present call state
N7 Call Received call state
N9 Incoming Call Proceeding call state
N-ISDN Narrowband Integrated Services Digital Network
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
Rest 0 Restart Null state
Rest 1 Restart Request state
Rest 2 Restart state
TP Test Purpose
TSS Test Suite Structure
VC Virtual Channel
VCI Virtual Channel Identifier
VP Virtual Path
VPC Virtual Path Connection
VPCI Virtual Path Connection Identifier
ETSI
8 ETSI EN 300 443-5 V1.2.1 (2000-10)
4 Test Suite Structure (TSS)
Signalling procedures at the coincident S /T and at the T reference points
B B B
Call/connection establishment at the originating interface
Connection identifier (VPCI/VCI) allocation/selection .(01)
Associated signalling.(02)
Non-associated signalling.(03)
QOS and traffic parameters selection procedures .(04)
Invalid call/connection control information .(05)
Call/connection proceeding.(06)
Call/connection confirmation indication.(07)
Call/connection acceptance.(08)
Call/connection rejection .(09)
Transit network selection .(10)
Call/connection establishment at the destination interface
Incoming call/connection request.(11)
Connection identifier (VPCI/VCI) allocation/selection .(12)
Associated signalling.(13)
Non-associated signalling.(14)
Call/connection confirmation.(15)
Call/connection acceptance.(16)
Call/connection clearing
Exception conditions.(17)
Clearing initiated by the user .(18)
Clearing initiated by the network.(19)
Clear collision .(20)
Restart procedure
Sending RESTART.(21)
Receipt of RESTART .(22)
Remote user.(23)
Handling of error conditions
Error handling in N0 .(24)
Error handling in N3 .(25)
Error handling in N4 .(26)
Error handling in N6 .(27)
Error handling in N7 .(28)
Error handling in N9 .(29)
Error handling in N10 - incoming call .(30)
Error handling in N10 - outgoing call .(31)
Error handling in N12 - incoming call .(32)
Error handling in N12 - outgoing call .(33)
Error handling in Rest 0 .(34)
Error handling in Rest 1 .(35)
Notification procedures .(36)
Signalling procedures for interworking between N-ISDN and B-ISDN
Interworking N-ISDN -> B-ISDN.(37)
Interworking B-ISDN -> N-ISDN.(38)
Figure 1: Test suite structure
ETSI
9 ETSI EN 300 443-5 V1.2.1 (2000-10)
5 Test Purposes (TP)
5.1 Introduction
For each test requirement a TP is defined.
5.1.1 TP naming convention
TPs are numbered, starting at 01, within each group. Groups are organized according to the TSS. Additional references
are added to identify the actual test suite (see table 1).
Table 1: TP identifier naming convention scheme
Identifier: __
= layer + type of IUT: "L3BN" for Layer 3Basic call/bearer control,
IUT = Network
= group number: two character field representing the group reference
according to TSS
= sequential number: (01-99)
5.1.2 Source of TP definition
The TPs are based on EN 300 443-1 [1].
5.1.3 Test strategy
As the base standard EN 300 443-1 [1] contains no explicit requirements for testing, the TPs were generated as a result
of an analysis of the base standard and the PICS specification EN 300 443-2 [2].
The TPs are only based on conformance requirements related to the externally observable behaviour of the IUT, and are
limited to conceivable situations to which a real implementation is likely to be faced (ETS 300 406 [6]).
5.1.4 Test of call states
Many TPs include a reference to the IUT's final call state after the realization of the TP. In these cases the TP includes
the requirement to ensure that the IUT has entered this particular final call state. Ensuring that the IUT is in a particular
call state shall be realized by following the procedures described in subclause 5.6.11 of EN 300 443-1 [1]. According to
these procedures, the IUT on receipt of a STATUS ENQUIRY message, shall respond with a STATUS message
indicating, in the fifth octet of the Call state information element, the current call state of the IUT. This exchange of
messages is not mentioned explicitly in each TP but is considered to be implicit in the reference to the final call state.
This way of phrasing the TPs has been used to avoid over-complicating the text and structure of the TPs and to improve
the readability.
ETSI
10 ETSI EN 300 443-5 V1.2.1 (2000-10)
5.2 TPs for the basic call/bearer control, layer 3, network
All PICS items referred to in this subclause are as specified in EN 300 443-2 [2] unless indicated otherwise by another
numbered reference.
Unless specified:
- the messages indicated are valid and contain at least the mandatory information elements and possibly optional
information elements;
- the information elements indicated are valid and contain at least the mandatory parameters and possibly optional
parameters.
5.2.1 Signalling procedures at the coincident S /T and at the T reference
B B B
points
Test purposes for EN 300 443-1 [1] subclause 5.1.
5.2.1.1 Call/connection establishment at the originating interface
Test purposes for EN 300 443-1 [1] subclause 5.1.
5.2.1.1.1 Connection identifier (VPCI/VCI) allocation/selection (01)
Test purposes for EN 300 443-1 [1] subclause 5.1.2.
L3BN_01_01
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = VP associated signalling),
- sends a RELEASE COMPLETE message (Cause value = 36) and remains in N0.
Selection: Associated signalling at the originating side NOT supported. PICS: NOT MCn 1.1.
5.2.1.1.1.1 Associated signalling (02)
Test purposes for EN 300 443-1 [1] subclause 5.1.2.1.
Selection: Associated signalling at the originating side supported. PICS: MCn 1.1.
L3BN_02_01
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = VP associated signalling, preferred exclusive = exclusive VPCI; any VCI), when a VCI is available in the
VPC carrying the signalling VC,
- sends a CALL PROCEEDING message (Connection identifier present, VP associated signalling = VP associated
signalling, preferred exclusive = exclusive VPCI; exclusive VCI, virtual channel identifier indicating a specific
VCI) and enters N3.
L3BN_02_02
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = VP associated signalling, preferred exclusive = exclusive VPCI; exclusive VCI, virtual channel identifier
indicating a specific VCI), when the requested VCI is available in the VPC carrying the signalling VC,
- sends a CALL PROCEEDING message (Connection identifier present, VP associated signalling = VP associated
signalling, preferred exclusive = exclusive VPCI; exclusive VCI, virtual channel identifier indicating the
requested VCI) and enters N3.
L3BN_02_03
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = VP associated signalling, preferred exclusive = exclusive VPCI; any VCI), when no VCI is available in the
VPC carrying the signalling VC,
- sends a RELEASE COMPLETE message (Cause value = 45) and remains in N0.
ETSI
11 ETSI EN 300 443-5 V1.2.1 (2000-10)
L3BN_02_04
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = VP associated signalling, preferred exclusive = exclusive VPCI; exclusive VCI, virtual channel identifier
indicating a specific VCI), when the requested VCI is not available in the VPC carrying the signalling VC,
- sends a RELEASE COMPLETE message (Cause value = 35) and remains in N0.
5.2.1.1.1.2 Non-associated signalling (03)
Test purposes for EN 300 443-1 [1] subclause 5.1.2.2.
L3BN_03_01
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; any VCI, virtual path connection
identifier indicating a specific VPCI), when a VCI is available within the requested VPCI,
- sends a CALL PROCEEDING message (Connection identifier present, VP associated signalling = explicit
indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection identifier
indicating the requested VPCI, virtual channel identifier indicating a specific VCI) and enters N3.
L3BN_03_02
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection
identifier indicating a specific VPCI, virtual channel identifier indicating a specific VCI), when the requested VCI is
available within the requested VPCI,
- sends a CALL PROCEEDING message (Connection identifier present, VP associated signalling = explicit
indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection identifier
indicating the requested VPCI, virtual channel identifier indicating the requested VCI) and enters N3.
L3BN_03_03
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier absent), when a VCI is available
within any VPCI,
- sends a CALL PROCEEDING message (Connection identifier present, VP associated signalling = explicit
indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection identifier
indicating a specific VPCI, virtual channel identifier indicating a specific VCI) and enters N3.
L3BN_03_04
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; any VCI, virtual path connection
identifier indicating a specific VPCI), when the requested VPCI is not available,
- sends a RELEASE COMPLETE message (Cause value = 35) and remains in N0.
L3BN_03_05
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection
identifier indicating a specific VPCI, virtual channel identifier indicating a specific VCI), when the requested VPCI is
not available,
- sends a RELEASE COMPLETE message (Cause value = 35) and remains in N0.
L3BN_03_06
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; any VCI, virtual path connection
identifier indicating a specific VPCI, virtual channel identifier indicating a specific VCI), when no VCI is available
within the requested VPCI,
- sends a RELEASE COMPLETE message (Cause value = 45) and remains in N0.
L3BN_03_07
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier present, VP associated
signalling = explicit indication of VPCI, preferred exclusive = exclusive VPCI; exclusive VCI, virtual path connection
identifier indicating a specific VPCI, virtual channel identifier indicating a specific VCI), when the requested VCI is not
available within the requested VPCI,
- sends a RELEASE COMPLETE message (Cause value = 35) and remains in N0.
ETSI
12 ETSI EN 300 443-5 V1.2.1 (2000-10)
L3BN_03_08
Ensure that the IUT in N0, on receipt of a SETUP message (Connection identifier absent), when no VCI is available
within any VPCI,
- sends a RELEASE COMPLETE message (Cause value = 45) and remains in N0.
5.2.1.1.2 QOS and traffic parameter selection procedures (04)
Test purposes for EN 300 443-1 [1] subclause 5.1.3.
L3BN_04_01
Ensure that the IUT in N0, on receipt of a SETUP message (Quality of service parameter present, requesting a QOS
class that can not be provided),
- sends a RELEASE COMPLETE message (Cause value = 49) and remains in N0.
NOTE: There is only one non-reserved value for the QOS class defined in EN 300 443-1 [1].
L3BN_04_02
Ensure that the IUT in N0, on receipt of a SETUP message (ATM traffic descriptor present, requesting a peak cell rate
that can not be provided),
- sends a RELEASE COMPLETE message (Cause value = 37) and remains in N0.
5.2.1.1.3 Invalid call/connection control information (05)
Test purposes for EN 300 443-1 [1] subclause 5.1.4.
L3BN_05_01
Ensure that the IUT in N0, on receipt of a SETUP message ( Called party number present, indicating invalid call
information, i.e. unassigned called party number),
- sends a RELEASE message (Cause value = 1) possibly preceded by a CALL PROCEEDING message and enters
N12orsendsaRELEASE COMPLETE message(Causevalue =1)and remainsinN0.
L3BN_05_02
Ensure that the IUT in N0, on receipt of a SETUP message ( Called party number present, indicating invalid call
information, i.e. no outgoing trunk direction exists for the called party number),
- sends a RELEASE message (Cause value = 3) possibly preceded by a CALL PROCEEDING message and enters
N12orsendsaRELEASE COMPLETE message(Causevalue =3)and remainsinN0.
L3BN_05_03
Ensure that the IUT in N0, on receipt of a SETUP message ( Called party number present, indicating invalid call
information, i.e. a called party number that has been changed),
- sends a RELEASE message (Cause value = 22) possibly preceded by a CALL PROCEEDING message and
enters N12 or sends a RELEASE COMPLETE message (Cause value = 22) and remains in N0.
L3BN_05_04
Ensure that the IUT in N0, on receipt of a SETUP message ( Called party number present, indicating invalid call
information, i.e. an incomplete called party number),
- sends a RELEASE message (Cause value = 28) possibly preceded by a CALL PROCEEDING message and
enters N12 or sends a RELEASE COMPLETE message (Cause value = 28) and remains in N0.
5.2.1.1.4 Call/connection proceeding (06)
Test purposes for EN 300 443-1 [1] subclause 5.1.5.
L3BN_06_01
Ensure that the IUT in N0, on receipt of a SETUP message (Broadband bearer capability requesting a service that is
authorized and available),
- sends a CALL PROCEEDING message and enters N3.
L3BN_06_02
Ensure that the IUT in N0, on receipt of a SETUP message (Broadband bearer capability requesting a service that is not
authorized),
- sends a RELEASE COMPLETE message (Cause value = 57) and remains in N0.
ETSI
13 ETSI EN 300 443-5 V1.2.1 (2000-10)
L3BN_06_03
Ensure that the IUT in N0, on receipt of a SETUP message (Broadband bearer capability requesting a service that is not
available),
- sends a RELEASE COMPLETE message (Cause value = 58, 63 or 65) and remains in N0.
5.2.1.1.5 Call/connection confirmation indication (07)
Test purposes for EN 300 443-1 [1] subclause 5.1.6.
L3BN_07_01
Ensure that the IUT in N3, to indicate that user alerting has been initiated at the called user's side,
- sends an ALERTING message and enters N4.
5.2.1.1.6 Call/connection acceptance (08)
Test purposes for EN 300 443-1 [1] subclause 5.1.7.
L3BN_08_01
Ensure that the IUT in N3, to indicate that the call has been accepted at the called user's side,
- sends a CONNECT message and enters N10.
L3BN_08_02
Ensure that the IUT in N4, to indicate that the call has been accepted at the called user's side,
- sends a CONNECT message and enters N10.
L3BN_08_03
Ensure that the IUT in N10, on receipt of a CONNECT ACKNOWLEDGE message,
- sends no message and remains in N10.
5.2.1.1.7 Call/connection rejection (09)
Test purposes for EN 300 443-1 [1] subclauses 5.1.8, 5.2.5, 5.4 and annex B.
L3BN_09_01
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (Broadband bearer
capability not supported),
- sends a RELEASE message (Cause value = 88) and enters N12.
L3BN_09_02
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (QOS class can not be
provided),
- sends a RELEASE message (Cause value = 49) and enters N12.
L3BN_09_03
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (peak cell rate can not
be provided),
- sends a RELEASE message (Cause value = 47) and enters N12.
L3BN_09_04
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (call rejected),
- sends a RELEASE message (Cause value = 21) and enters N12.
L3BN_09_05
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (user busy),
- sends a RELEASE message (Cause value = 17) and enters N12.
L3BN_09_06
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (second expiry of
T303),
- sends a RELEASE message (Cause value = 18) and enters N12.
ETSI
14 ETSI EN 300 443-5 V1.2.1 (2000-10)
L3BN_09_07
Ensure that the IUT in N3, to indicate that the call has not been accepted at the called user's side (expiry of T310),
- sends a RELEASE message (Cause value = 18) and enters N12.
L3BN_09_08
Ensure that the IUT in N4, to indicate that the call has not been accepted at the called user's side (expiry of T301),
- sends a RELEASE message (Cause value = 19) and enters N12.
5.2.1.1.8 Transit network selection (10)
Test purposes for EN 300 443-1 [1] subclause 5.1.9, annex D.
Selection: Transit network selection procedures supported. PICS: MCn 11
L3BN_10_01
Ensure that the IUT in N0, on receipt of a SETUP message (Transit network selection indicating a transit network not
recognized by the IUT),
- sends a RELEASE message (Cause value = 2) preceded by a CALL PROCEEDING message and enters N12.
L3BN_10_02
Ensure that the IUT in N0, on receipt of a SETUP message (Transit network selection indicating the transit network
selectioninanincorrect format),
- sends a RELEASE message (Cause value = 91) preceded by a CALL PROCEEDING message and enters N12.
L3BN_10_03
Ensure that the IUT in N0, on receipt of a SETUP message (Transit network selection indicating valid network selection
information), to indicate that it can not route the call to the requested direction due to insufficient bandwidth,
- sends a RELEASE message (Cause value = 37) preceded by a CALL PROCEEDING message and enters N12.
5.2.1.2 Call/connection establishment at the destination interface
Test purposes for EN 300 443-1 [1] subclause 5.2.
5.2.1.2.1 Incoming call/connection request (11)
Test purposes for EN 300 443-1 [1] subclauses 5.2.1 and 5.2.4.
L3BN_11_01
Ensure that the IUT in N0, to indicate the arrival of a call,
- sends a SETUP message (Quality of service parameter, ATM traffic descriptor present) and enters N6.
L3BN_11_02
Ensure that the IUT in N0, to indicate the arrival of a call by using the en bloc receiving procedures,
- sends a SETUP message (Quality of service parameter, ATM traffic descriptor, Broadband sending complete
present) and enters N6.
L3BN_11_03
Ensure that the IUT in N6, on the first expiry of T303,
- sends a SETUP message (same contents as the first SETUP message) and remains in N6.
L3BN_11_04
Ensure that the IUT in N6, on the second expiry of T303,
- sends a no message and enters N0.
ETSI
15 ETSI EN 300 443-5 V1.2.1 (2000-10)
5.2.1.2.2 Connection identifier (VPCI/VCI) allocation/selection (12)
Test purposes for EN 300 443-1 [1] subclause 5.2.3.
Selection: Associated signalling on the destination side NOT supported. PICS: NOT MCn 2.1
L3BN_12_01
Ensure that the IUT in N6, on receipt of a CALL PROCEEDING message (Connection identifier present, VP associated
signalling = VP associated signalling),
- sends a RELEASE message (Cause value = 36) and enters N12.
L3BN_12_02
Ensure that the IUT in N6, on receipt of an ALERTING message (Connection identifier present, VP associated
signalling = VP associated signalling),
- sends a RELEASE message (Cause value = 36) and enters N12.
L3BN_12_03
Ensure that the IUT in N6, on receipt of a CONNECT message (Connection identifier present, VP associated
signalling = VP associated signalling),
- sends a RELEASE message (Cause value = 36) and enters N12.
5.2.1.2.2.1 Associated signalling (13)
Test purposes for EN 300 443-1 [1] subclause 5.2.3.1.
Selection: Associated signalling on the destination side supported. PICS: MCn 2.1
L3BN_13_01
Ensure that the IUT in N0, to indicate the arrival of a call,
- sends a SETUP message (Connection identifier present, VP associated signalling = VP associated signalling)
and enters N6.
5.2.1.2.2.2 Non-associated signalling (14)
Test purposes for EN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...