SIST EN 62329-3-101:2010

Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance (IEC 62329-3-101:2010)

This sheet of IEC 62329-3 gives the requirements for heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. Experience of product performance indicates that this moulded shape material is suitable for inclusion in systems for operation in the following temperature range: -30 °C to + 105 °C. The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers for options. A guide to adhesive compatibility is given in Annex A. These moulded shapes are normally supplied in the styles and dimensions given in IEC 62329-3- 100. The colour is normally black. Styles and dimensions other than those specifically listed in IEC 62329-3-100 may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 1 with the exception of dimensions. Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Wärmeschrumpfende Formteile - Teil 3: Anforderungen für Formteilmaße, Materialeigenschaften und Kompatibilitätsverhalten - Blatt 101: Wärmeschrumpfende Formteile aus Polyolefin, halbsteif, flammwidrig, Materialanforderungen und Systemeigenschaften (IEC 62329-3-101:2010)

Profilés thermorétractables - Partie 3: Exigences relatives aux dimensions des profilés, exigences de matériaux et performances de compatibilité - Feuille 101: Profilés thermorétractables, exigences relatives aux matériaux semi-rigides en polyoléfine, à risque de feu limité et performances du système (CEI 62329-3-101:2010)

La CEI 62329-3-101:2010 définit les exigences relatives aux profilés thermorétractables, en matériau semi-rigide polyoléfine, à risque de feu limité, et aux performances du système. L'expérience en matière de performance des produits indique que les matériaux de profilés sont adaptés à leur intégration dans des systèmes pour des utilisations dans la plage de températures de -30 °C à +105 °C.

Toplotno skrčljive ulite oblike - 3. del: Specifikacijske zahteve za mere oblik, material in skladnost - 101. list: Toplotno skrčljive ulite oblike iz poliolefina, poltoge, z majhno požarno nevarnostjo, omejenimi zahtevami za material in lastnosti sistema (IEC 62329-3-101:2010)

Ta list IEC 62329-3 podaja zahteve za toplotno skrčljive ulite oblike iz poliolefina, poltoge, z majhno požarno nevarnostjo, zahteve za material in lastnosti sistema. Izkušnje glede lastnosti izdelka nakazujejo, da je ta material za ulite oblike primeren za vključitev v sisteme za operacijo v naslednjem temperaturnem razponu: od -30 C do + 105 °C. Ulite oblike se lahko dobavljajo predhodno premazane z lepilom. O možnostih se pozanimajte pri proizvajalcih/dobaviteljih. Vodilo o združljivosti lepila je podano v Dodatku A. Te ulite oblike se običajno dobavljajo v slogih in merah, podanih v IEC 62329-3-100. Običajno so črne barve. Slogi in mere, ki niso izrecno navedeni v IEC 62329-3-100, so lahko na voljo na zahtevo. Ti predmeti so skladni s tem standardom, če izpolnjujejo zahteve glede lastnosti, navedene v preglednici 1, z izjemo mer. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri takšni uporabi, in ne le na podlagi same specifikacije.

General Information

• Status: Published
• Publication Date: 19-Oct-2010
• ICS: 29.035.01 - Insulating materials in general
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Oct-2010
• Due Date: 10-Dec-2010
• Completion Date: 20-Oct-2010
• Ref Project: EN 62329-3-101:2010 - Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wärmeschrumpfende Formteile - Teil 3: Anforderungen für Formteilmaße, Materialeigenschaften und Kompatibilitätsverhalten - Blatt 101: Wärmeschrumpfende Formteile aus Polyolefin, halbsteif, flammwidrig, Materialanforderungen und Systemeigenschaften (IEC 62329-3-101:2010)Profilés thermorétractables - Partie 3: Exigences relatives aux dimensions des profilés, exigences de matériaux et performances de compatibilité - Feuille 101: Profilés thermorétractables, exigences relatives aux matériaux semi-rigides en polyoléfine, à risque de feu limité et performances du système (CEI 62329-3-101:2010)Heat-shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance (IEC 62329-3-101:2010)29.035.01Izolacijski materiali na splošnoInsulating materials in generalICS:Ta slovenski standard je istoveten z:EN 62329-3-101:2010SIST EN 62329-3-101:2010en01-december-2010SIST EN 62329-3-101:2010SLOVENSKI
STANDARD



SIST EN 62329-3-101:2010



EUROPEAN STANDARD EN 62329-3-101 NORME EUROPÉENNE
EUROPÄISCHE NORM September 2010
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62329-3-101:2010 E
ICS 29.035.01
English version
Heat-shrinkable moulded shapes -
Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance -
Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance (IEC 62329-3-101:2010)
Profilés thermorétractables -
Partie 3: Exigences relatives
aux dimensions des profilés, exigences
de matériaux et performances
de compatibilité -
Feuille 101: Profilés thermorétractables, exigences relatives aux matériaux
semi-rigides en polyoléfine, à risque
de feu limité et performances du système (CEI 62329-3-101:2010)
Wärmeschrumpfende Formteile -
Teil 3: Anforderungen für Formteilmaße, Materialeigenschaften
und Kompatibilitätsverhalten -
Blatt 101: Wärmeschrumpfende Formteile aus Polyolefin, halbsteif, flammwidrig, Materialanforderungen
und Systemeigenschaften (IEC 62329-3-101:2010)
This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 62329-3-101:2010



EN 62329-3-101:2010 - 2 - Foreword The text of document 15/569/FDIS, future edition 1 of IEC 62329-3-101, prepared by IEC TC 15, Solid electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62329-3-101 on 2010-09-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2011-06-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2013-09-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 62329-3-101:2010 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 60684-3-216 NOTE
Harmonized as EN 60684-3-216. __________ SIST EN 62329-3-101:2010



- 3 - EN 62329-3-101:2010 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60695-11-10 - Fire hazard testing -
Part 11-10: Test flames - 50 W horizontal
and vertical flame test methods EN 60695-11-10 -
IEC 60757 1983 Code for designation of colours HD 457 S1 1985
IEC 62329-1 - Heat shrinkable moulded shapes -
Part 1: Definitions and general requirements EN 62329-1
-
IEC 62329-2 2006 Heat shrinkable moulded shapes -
Part 2: Methods of test EN 62329-2 2006
IEC 62329-3-100 2010 Heat-shrinkable moulded shapes -
Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance -
Sheet 100: Heat-shrinkable moulded shape dimensions EN 62329-3-100 2010
ISO 1817 2005 Rubber, vulcanized - Determination of the effect of liquids - -
SIST EN 62329-3-101:2010



SIST EN 62329-3-101:2010



IEC 62329-3-101Edition 1.0 2010-06INTERNATIONAL STANDARD NORME INTERNATIONALEHeat-shrinkable moulded shapes –
Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance – Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance
Profilés thermorétractables –
Partie 3: Exigences relatives aux dimensions des profilés, exigences de matériaux et performances de compatibilité – Feuille 101: Profilés thermorétractables, exigences relatives aux matériaux semi-rigides en polyoléfine, à risque de feu limité, et performances du système
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE MICS 29.035.01 PRICE CODECODE PRIXISBN 978-2-88912-010-9
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ® SIST EN 62329-3-101:2010



– 2 – 62329-3-101 © IEC:2010 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references.6 3 Designation.7 4 Conditions of test for the moulded shapes.7 5 Requirements.7 6 Moulded shapes material conformance.7 7 Moulded shapes compatibility.7 Annex A (informative)
Adhesive compatibility guide for sheet 101 moulded shapes.11 Bibliography.12
Table 1 – Property requirements.8 Table 2 – Resistance to selected fluids.10
SIST EN 62329-3-101:2010



62329-3-101 © IEC:2010 – 3 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
HEAT-SHRINKABLE MOULDED SHAPES –
Part 3: Specification requirements for shape dimensions,
material requirements and compatibility performance –
Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid,
limited fire hazard, material requirements and system performance
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible fo
...