Abstract

This document specifies the safety requirements relevant to load-handling functions for rough-terrain variable reach tractors (RTVR tractors). This includes the safety requirements for their permanently mounted equipment (PME).
Fork arms are considered to be part of the PME. RTVR tractors can also be equipped with a variety of attachments (e.g. bale spikes, mowers, sweepers).
This document deals with all the significant hazards, hazardous situations and events relevant to the operation of the PME of RTVR tractors when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
This document does not apply to:
—   rough-terrain variable-reach trucks covered by EN 1459 1:2025;
—   slewing rough-terrain variable-reach trucks covered by EN 1459 2:2015+A1:2018;
—   industrial variable reach trucks covered by EN ISO 3691 2:2023;
—   lorry-mounted variable-reach trucks covered by ISO 20297 1:2017;
—   RTVR tractors fitted with tilting or elevating operator position;
—   mobile cranes covered by EN 13000:2010+A1:2014;
—   machines designed primarily for earth moving, even if their buckets and blades are replaced with forks (see the EN 474 series);
—   RTVR tractors designed primarily with variable length load suspension elements (e.g. chain, ropes) from which the load can swing freely in all directions;
—   RTVR tractors designed primarily for container handling;
—   RTVR tractors on tracks;
—   RTVR tractors with articulated chassis;
—   front loaders covered by EN 12525:2000+A2:2010;
—   attachments.
Determination and declaration of sound power level is not addressed by this document.
This document does not cover sales literature.
Consistency of single lever (if fitted) and movement of the RTVR tractor when travelling in the forward direction is not covered by this document.
This document does not address hazards linked to:
—   operation of the RTVR tractor from a position other than the normal operating position or the remote control;
—   gas power systems;
—   gasoline engine systems.
This document does not address hazards which can occur:
a)   when handling suspended loads which can swing freely (additional requirements are given in EN 1459 4:2020+A1:2025);
b)   when using RTVR tractors on public roads;
c)   when operating in potentially explosive atmospheres (additional requirements are given in EN 1755:2024);
d)   when operating underground;
e)   when towing trailers;
f)   when fitted with a personnel work platform (additional requirements are given in EN 1459 3:2015 and EN 1459 9:2021);
g)   when using system capable of controlling the speed of the RTVR tractor as set by the operator (cruise-control).
This document does not provide a method of calculation for fatigue and strength of material.
This document is not applicable to RTVR tractors manufactured before the date of its publication.

Status
Not Published
Public Enquiry End Date
30-Jul-2025
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
11-Nov-2026
Due Date
16-Jan-2027

Buy Documents

Draft

oSIST prEN 17968:2025

English language (63 pages)
Preview
Preview
e-Library read for
×1 day

SIST EN 17968:2027 is a Slovenian standard published by SIST for rough-terrain variable-reach tractors (RTVR tractors). It specifies safety requirements and verification for permanently mounted equipment (PME) used for load handling, including fork arms, so manufacturers, assessors, buyers and maintenance teams can see how these machines are to be designed, checked and marked.

What does SIST EN 17968:2027 specify?

SIST EN 17968:2027 specifies safety requirements for the load-handling functions of RTVR tractors and the PME fitted to them. It focuses on the hazards created by the machine in normal use and by reasonably foreseeable misuse, and it sets out how those risks are to be reduced and verified.

The document is organized into six main clauses and three annexes.

AnnexWhat it covers
Annex AList of significant hazards
Annex BConsistency of motions
Annex CRules for the construction and layout of pedals

The scope excludes other machine families such as rough-terrain variable-reach trucks, slewing trucks, industrial variable reach trucks, lorry-mounted variable-reach trucks, mobile cranes, front loaders, earth-moving machines, machines on tracks, articulated chassis machines, and attachments as separate items. It also leaves out several special operating cases, including public-road use, explosive atmospheres, underground use, towing trailers, personnel work platforms, freely swinging suspended loads, cruise-control, and operation from a position other than the normal operating position or remote control. The document also excludes sound power level determination, sales literature, and fatigue or strength calculation methods.

What are the key requirements of SIST EN 17968:2027?

Control systems, starting, stopping and travel safety

SIST EN 17968:2027 gives detailed safety requirements for starting, stopping and motion control in Clause 4.2, 4.5 and 4.6. In practice, this means the machine must be arranged so that unsafe travel or load movement cannot happen just because the operator is absent, returns to the station, or moves a control unintentionally.

Several of these functions are tied to the safety-related parts of control systems in Table 2, with requirements expressed as PLr or SIL. That matters because the designer must choose and document a control-system performance level that matches the risk.

Key points include:

  • prevention of unauthorized starting and unintended movement
  • prevention of uncontrolled motion from rest on level ground
  • powered travel only when the operator is at the normal operating position
  • parking-brake functions that do not create new hazards
  • remote control that blocks conflicting normal-position controls, while keeping an emergency stop available at the normal operating position

Brakes, steering and control layout

Clause 4.3 and 4.5 require the service brake, parking brake and steering arrangements to behave predictably. For example, the service brake must hold a laden machine motionless on the maximum slope permitted by the manufacturer, and steering controls are tested under defined loaded conditions.

This matters because the standard is not only about stopping the machine, but about stopping it safely under real working loads. Annex C also sets out pedal layout and construction rules so that the operator can brake, clutch and inch without confusion.

The document also covers:

  • differential locking indication and marking
  • steering direction in crab-steering mode
  • visual indication for selected multi-function modes
  • automatic locking and unlock indication for axle oscillation locking
  • clear marking of stabilizer controls and sway/levelling controls

Electrical, hydraulic and structural safety

Clause 4.4, 4.7 and 4.10 set requirements for electrical protection, hydraulic integrity and the lifting or reaching system. Electrical and electronic parts need suitable protection ratings, wiring identification and protection against electric shock, while the control system safety functions are linked to Table 2.

The hydraulic system must withstand pressure and keep the load held if there is leakage, a fault or loss of power. That is important because the machine must not drop or drift a load when a hose, valve or power supply fails.

The lifting and reaching system also has defined strength expectations:

  • chains and wire ropes must meet minimum strength factors
  • fork arms must comply with ISO 2330 and be secured against unintended disengagement
  • the attachment interface must meet EN 1459-5
  • mechanisms with travel limits need mechanical stops or equivalent cylinder design

Stability, protection structures and operator station

Clause 4.8, 4.13, 4.14 and 4.15 deal with the machine's stability and the operator's protection. RTVR tractors must meet ISO 22915-14, carry a longitudinal load moment indicator (LLMI) and a longitudinal load moment control (LLMC), and use an inclinometer for lateral slope at the operating position.

The operator protection requirements include ROPS and FOPS, guarding of hot or moving parts, protection against crushing and trapping, and measures for visibility and lighting. For compact RTVR tractors the FOPS level is different from other RTVR tractors, which matters when choosing a machine for a given work site.

The operator station also has practical comfort and safety requirements:

  • storage for the instruction manual
  • wipers and washers where fitted
  • ventilation and air conditioning requirements where fitted
  • operator restraint systems, including seat belt warnings
  • visibility of indicators and displays in daylight and darkness

Marking, load charts and information for use

Clause 6 requires the PME to be marked with identification, conformity marking, serial number, year of construction and rated capacity. Where load-carrying attachments are authorized, the machine must carry durable, readable load charts that match the attachment, load centre distance, actual capacities and stabilizer configuration.

The instruction handbook has to cover operation, maintenance, transportation, lifting, daily checks, residual risks, prohibited uses and noise and vibration information. In practice, this is the information users need to operate the machine within its approved limits and to keep the safety functions effective over time.

What terms does SIST EN 17968:2027 define?

  • rough-terrain variable-reach tractor (RTVR tractor) - A tractor with one telescopic articulated arm, non-slewing or slewing by not more than 5° either side of the longitudinal axis, used for stacking loads.
  • permanently mounted equipment (PME) - The load-handling part of the RTVR tractor, including the telescopic articulated arm and the load-handling device fitted to it.
  • actual capacity (Q) - The maximum load the manufacturer allows for a given configuration, based on strength and stability, at specified height, reach and load-centre distance.
  • rated capacity (Q1) - The maximum load permitted on fork arms with the boom fully retracted and the standard load centre distance.
  • reach (d) - The horizontal distance used to express the position of the load relative to the front of the front tyres.
  • stabilizing devices - Extendable or pivoting supports used to improve stability when the RTVR tractor is stationary.
  • normal operating position - The position specified by the manufacturer from which the operator controls the machine, including load-handling functions.

Who uses SIST EN 17968:2027?

SIST EN 17968:2027 is mainly used by machine manufacturers who design RTVR tractors and their PME, and by the teams that verify braking, stability, control functions, load charts, markings and instructions. It is also used by safety bodies such as regulators, accident-prevention organizations and market-surveillance teams.

In practice, the standard is also relevant for:

  • users and employers who operate the machines
  • maintenance and service providers
  • conformity assessment and testing personnel
  • buyers who need to specify a safe machine configuration and the right attachments

What changed in SIST EN 17968:2027 from the previous edition?

SIST EN 17968:2027 supersedes CEN/TS 1459-8:2018. The European foreword states that the technical changes are:

  • alignment to the requirements of EN 1459-1:2025
  • updated normative references
  • other minor changes, mainly editorial clarifications of existing requirements

Which standards are used with SIST EN 17968:2027?

The document relies on several referenced standards to define test methods, control-system design, stability, protection structures and marking. The most important are:

ReferenceWhat it contributes
EN ISO 12100Risk assessment and risk reduction framework
EN ISO 13849-1 / EN IEC 62061Safety-related parts of control systems
EN 1459-5Attachment interface requirements
EN 15000LLMI and load moment limiting functions
ISO 22915-14Stability verification for RTVR trucks
EN 15830Visibility test methods and verification
EN ISO 3471 / EN ISO 3449ROPS and FOPS requirements
EN ISO 4413Hydraulic system safety rules
ISO 15817Remote operator control systems
ISO 2330 / ISO 2328Fork arm characteristics and mounting dimensions
EN 12053 / EN 13059Noise and vibration measurement methods
EN ISO 6683 / EN 17314Operator restraint systems

The scope also names related parts for special cases, including EN 1459-4 for freely suspended loads, EN 1459-3 and EN 1459-9 for personnel work platforms, and EN 1755 for potentially explosive atmospheres.

What does the SIST EN 17968:2027 document contain?

SIST EN 17968:2027 contains a full set of machine-safety clauses for RTVR tractors, covering controls, brakes, electrical protection, hydraulics, operator station design, stability, visibility, lighting, fire protection, transportation and lifting provisions, noise, and electromagnetic radiation. It uses a mix of design checks, visual examination, measurements, functional tests and structural tests to verify compliance.

The document also includes Table 2 for safety-related control functions, Table 3 for chain and wire rope strength factors, Annex B for consistent control movements, and Annex C for pedal layout and construction. Figures support the definitions and marking of lift points, tie-down points, retrieval points, symbols and load charts, while the instruction requirements define what the operator manual and PME marking have to communicate in practice.

Relations

Effective Date
19-Jan-2023
Effective Date
18-Jan-2023
Effective Date
28-Dec-2022

Buy Documents

Draft

oSIST prEN 17968:2025

English language (63 pages)
Preview
Preview
e-Library read for
×1 day

Frequently Asked Questions

SIST EN 17968:2027 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Rough-terrain variable-reach tractors - Safety requirements and verification for permanently mounted equipment". This standard covers: This document specifies the safety requirements relevant to load-handling functions for rough-terrain variable reach tractors (RTVR tractors). This includes the safety requirements for their permanently mounted equipment (PME). Fork arms are considered to be part of the PME. RTVR tractors can also be equipped with a variety of attachments (e.g. bale spikes, mowers, sweepers). This document deals with all the significant hazards, hazardous situations and events relevant to the operation of the PME of RTVR tractors when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). This document does not apply to: — rough-terrain variable-reach trucks covered by EN 1459 1:2025; — slewing rough-terrain variable-reach trucks covered by EN 1459 2:2015+A1:2018; — industrial variable reach trucks covered by EN ISO 3691 2:2023; — lorry-mounted variable-reach trucks covered by ISO 20297 1:2017; — RTVR tractors fitted with tilting or elevating operator position; — mobile cranes covered by EN 13000:2010+A1:2014; — machines designed primarily for earth moving, even if their buckets and blades are replaced with forks (see the EN 474 series); — RTVR tractors designed primarily with variable length load suspension elements (e.g. chain, ropes) from which the load can swing freely in all directions; — RTVR tractors designed primarily for container handling; — RTVR tractors on tracks; — RTVR tractors with articulated chassis; — front loaders covered by EN 12525:2000+A2:2010; — attachments. Determination and declaration of sound power level is not addressed by this document. This document does not cover sales literature. Consistency of single lever (if fitted) and movement of the RTVR tractor when travelling in the forward direction is not covered by this document. This document does not address hazards linked to: — operation of the RTVR tractor from a position other than the normal operating position or the remote control; — gas power systems; — gasoline engine systems. This document does not address hazards which can occur: a) when handling suspended loads which can swing freely (additional requirements are given in EN 1459 4:2020+A1:2025); b) when using RTVR tractors on public roads; c) when operating in potentially explosive atmospheres (additional requirements are given in EN 1755:2024); d) when operating underground; e) when towing trailers; f) when fitted with a personnel work platform (additional requirements are given in EN 1459 3:2015 and EN 1459 9:2021); g) when using system capable of controlling the speed of the RTVR tractor as set by the operator (cruise-control). This document does not provide a method of calculation for fatigue and strength of material. This document is not applicable to RTVR tractors manufactured before the date of its publication.

This document specifies the safety requirements relevant to load-handling functions for rough-terrain variable reach tractors (RTVR tractors). This includes the safety requirements for their permanently mounted equipment (PME). Fork arms are considered to be part of the PME. RTVR tractors can also be equipped with a variety of attachments (e.g. bale spikes, mowers, sweepers). This document deals with all the significant hazards, hazardous situations and events relevant to the operation of the PME of RTVR tractors when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). This document does not apply to: — rough-terrain variable-reach trucks covered by EN 1459 1:2025; — slewing rough-terrain variable-reach trucks covered by EN 1459 2:2015+A1:2018; — industrial variable reach trucks covered by EN ISO 3691 2:2023; — lorry-mounted variable-reach trucks covered by ISO 20297 1:2017; — RTVR tractors fitted with tilting or elevating operator position; — mobile cranes covered by EN 13000:2010+A1:2014; — machines designed primarily for earth moving, even if their buckets and blades are replaced with forks (see the EN 474 series); — RTVR tractors designed primarily with variable length load suspension elements (e.g. chain, ropes) from which the load can swing freely in all directions; — RTVR tractors designed primarily for container handling; — RTVR tractors on tracks; — RTVR tractors with articulated chassis; — front loaders covered by EN 12525:2000+A2:2010; — attachments. Determination and declaration of sound power level is not addressed by this document. This document does not cover sales literature. Consistency of single lever (if fitted) and movement of the RTVR tractor when travelling in the forward direction is not covered by this document. This document does not address hazards linked to: — operation of the RTVR tractor from a position other than the normal operating position or the remote control; — gas power systems; — gasoline engine systems. This document does not address hazards which can occur: a) when handling suspended loads which can swing freely (additional requirements are given in EN 1459 4:2020+A1:2025); b) when using RTVR tractors on public roads; c) when operating in potentially explosive atmospheres (additional requirements are given in EN 1755:2024); d) when operating underground; e) when towing trailers; f) when fitted with a personnel work platform (additional requirements are given in EN 1459 3:2015 and EN 1459 9:2021); g) when using system capable of controlling the speed of the RTVR tractor as set by the operator (cruise-control). This document does not provide a method of calculation for fatigue and strength of material. This document is not applicable to RTVR tractors manufactured before the date of its publication.

SIST EN 17968:2027 is classified under the following ICS (International Classification for Standards) categories: 53.060 - Industrial trucks. The ICS classification helps identify the subject area and facilitates finding related standards.

SIST EN 17968:2027 has the following relationships with other standards: It is inter standard links to SIST-TS CEN/TS 1459-8:2019, SIST-TS CEN/TS 1459-8:2019, SIST-TS CEN/TS 1459-8:2019. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

SIST EN 17968:2027 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

SIST EN 17968:2027 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
oSIST prEN 17968:2025
01-julij-2025
Traktorji z mehanizmom s spremenljivim dosegom- Terenska vozila - Varnostne
zahteve in preverjanje za trajno nameščeno opremo
Rough-terrain variable-reach tractors - Safety requirements and verification for
permanently mounted equipment
Geländegängige Traktoren mit veränderlicher Reichweite - Sicherheitstechnische
Anforderungen und Verifizierung für permanent montierte Ausrüstung
Tracteurs tout-terrain à portée-variable - Exigences de sécurité et vérification pour les
équipements montés en permanence
Ta slovenski standard je istoveten z: prEN 17968
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN 17968:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 17968:2025
oSIST prEN 17968:2025
DRAFT
EUROPEAN STANDARD
prEN 17968
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2025
ICS 53.060 Will supersede CEN/TS 1459-8:2018
English Version
Rough-terrain variable-reach tractors - Safety
requirements and verification for permanently mounted
equipment
Tracteurs tout-terrain à portée-variable - Prescriptions Geländegängige Traktor mit veränderlicher Reichweite
de sécurité et vérification - Sicherheitstechnische Anforderungen und
Verifizierung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 150.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17968:2025 E
worldwide for CEN national Members.

oSIST prEN 17968:2025
prEN 17968:2025 (E)
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 11
4 Safety requirements and/or protective/risk reduction measures . 17
4.1 General. 17
4.1.1 Introduction . 17
4.1.2 Sharp edges and acute angles . 17
4.1.3 Stored energy components . 17
4.2 Starting/stopping of engine and moving machine . 17
4.2.1 Unauthorized starting . 17
4.2.2 Stopping system . 17
4.2.3 Unintended movement . 17
4.2.4 Uncontrolled motion . 18
4.2.5 Powered travel movement . 18
4.2.6 Non-activation of the parking brake . 18
4.3 Brakes . 18
4.3.1 General. 18
4.3.2 Failure of energy supply . 18
4.3.3 Holding performance . 18
4.4 Electrical and electronic systems . 19
4.4.1 General. 19
4.4.2 Safety related parts of control systems . 19
4.4.3 Degree of protection . 19
4.4.4 Identification of wiring . 19
4.4.5 Protection against electric shock . 19
4.4.6 Batteries . 19
4.5 Controls at the normal operating position . 19
4.5.1 General. 19
4.5.2 Differential locking . 20
4.5.3 Steering controls . 20
4.5.4 Load handling controls . 22
4.5.5 Multi-function controls . 22
4.5.6 Stabilizing device control . 22
4.5.7 Sway/levelling control . 23
4.5.8 Axle oscillation locking . 23
4.6 Remote control . 23
4.7 Power systems and accessories . 24
4.7.1 Exhaust system . 24
4.7.2 Cooling system . 24
4.7.3 Tanks and pressure vessels . 24
4.8 Stabilizing devices . 24
4.9 Design requirements for maintenance purposes . 26
4.9.1 General. 26
oSIST prEN 17968:2025
prEN 17968:2025 (E)
4.9.2 Boom support device . 26
4.9.3 Tiltable cab support device . 27
4.10 Systems for lifting, tilting and reaching . 27
4.10.1 Chains and wire ropes . 27
4.10.2 Hydraulic system . 28
4.10.3 Maximum load lowering speed . 29
4.10.4 Limitation of stroke . 29
4.10.5 Fork arms . 29
4.10.6 Attachment interface . 30
4.11 Operator’s station . 30
4.11.1 General requirements . 30
4.11.2 Operator’s manual storage . 30
4.11.3 Pipes and hoses . 30
4.11.4 Operator's station . 30
4.11.5 Operator's seat . 32
4.11.6 Control panels, and symbols on displays . 33
4.12 Operator access . 33
4.12.1 General requirements . 33
4.12.2 Operator’s station openings . 33
4.13 Protective measures and devices . 33
4.13.1 Hot parts . 33
4.13.2 Protection against crushing, shearing and trapping . 33
4.13.3 Guards . 34
4.13.4 Engine compartment . 34
4.13.5 Fenders . 34
4.13.6 ROPS and FOPS . 34
4.13.7 Audible warning devices . 34
4.14 Stability requirements . 34
4.15 Visibility . 35
4.16 Lighting . 35
4.17 Fire protection . 35
4.17.1 Fire resistance . 35
4.17.2 Fire extinguisher . 35
4.18 Retrieval, transportation and lifting . 35
4.18.1 General . 35
4.18.2 Retrieval . 35
4.18.3 Tying-down . 35
4.18.4 Lifting . 36
4.19 Noise . 36
4.19.1 Noise emission reduction . 36
4.19.2 Emission sound pressure level at the operator's station . 37
4.20 Electromagnetic radiation . 37
5 Verification of safety requirements and/or protective/risk reduction measures . 37
5.1 General . 37
5.2 Functional verification . 37
5.3 Structural verification . 37
5.3.1 Test loads . 37
5.3.2 Static test . 38
5.3.3 Dynamic tests . 38
5.4 Load holding verification . 39
6 Information for use . 39
6.1 General . 39
oSIST prEN 17968:2025
prEN 17968:2025 (E)
6.2 Graphical symbols and warning . 39
6.2.1 Safety signs and graphical symbols . 39
6.2.2 Graphical symbol of lift points . 39
6.2.3 Graphical symbol of tie-down points . 40
6.2.4 Graphical symbol of retrieval points . 40
6.2.5 Graphical symbol for pneumatic tyre inflation pressures . 41
6.2.6 Graphical symbol for fuel filling points . 41
6.2.7 Graphical symbol for hydraulic fluid filling points . 42
6.2.8 Graphical symbols for stored energy components . 42
6.2.9 Graphical symbol for brake fluid filling points . 43
6.2.10 Graphical symbol for battery disconnection . 44
6.2.11 Warnings . 44
6.3 Instruction handbook. 44
6.3.1 General. 44
6.3.2 Operating and maintenance instructions . 45
6.4 Marking of PME . 48
6.5 Load chart . 49
Annex A (informative) List of significant hazards . 51
Annex B (informative) Consistency of motions . 57
Annex C (normative) Rules for the construction and layout of pedals . 59
C.1 Definitions . 59
C.1.1 pedal . 59
C.1.2 service brake pedal . 59
C.1.3 clutch pedal . 59
C.1.4 inching pedal . 59
C.1.5 accelerator pedal . 59
C.2 Requirements . 59
C.2.1 General. 59
C.2.2 Service brake pedal . 59
C.2.3 Clutch pedal . 60
C.2.4 Accelerator pedal . 60
C.2.5 Inching pedal . 60
C.3 Design and manufacture . 60
Bibliography . 62

oSIST prEN 17968:2025
prEN 17968:2025 (E)
European foreword
This document (prEN 17968:2025) has been prepared by Technical Committee CEN/TC 150 “Industrial
trucks - Safety”, the secretariat of which is held by BSI.
This document will supersede CEN/TS 1459-8:2018.
In comparison with the previous edition CEN/TS 1459-8:2018, the following technical modifications
have been made:
— alignment to requirements of EN 1459-1:2025;
— update of normative references;
— other minor changes, mainly editorial clarifications of existing requirements.
This document has been prepared under a standardization request given to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
oSIST prEN 17968:2025
prEN 17968:2025 (E)
Introduction
This document covers general safety requirements and the means for verification of these requirements
for rough-terrain variable-reach tractors (RTVR tractors).
All quantities are in SI units, and this includes metric units.
This document is a type C standard as stated in EN ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the provisions of the other
standards, for machines that have been designed and built according to the provisions of this type C
standard.
Two legislative frameworks involve RTVR tractors:
— Regulation (EU) No 167/2013 providing requirements for the type-approval of agricultural and
forestry vehicles, also known as Tractor Mother Regulation (TMR), which trucks are homologated
according to. A number of additional Regulations supplements this one, such as:
— Delegated Regulation (EU) No 1322/2014 with regard to construction and general requirements
of agricultural and forestry vehicles;
— Delegated Regulation (EU) 2015/208 with regard to functional safety requirements of
agricultural and forestry vehicles;
— Delegated Regulation (EU) 2015/68 with regard to braking systems of agricultural and forestry
vehicles;
— Delegated Regulation (EU) 2018/985 as regards environmental and propulsion unit
performance requirements for agricultural and forestry vehicles and their engines;
— Implementing Regulation (EU) 2015/504 with regard to the administrative requirements of
agricultural and forestry vehicles.
oSIST prEN 17968:2025
prEN 17968:2025 (E)
— Directive 2006/42/EC as the permanently mounted equipment (PME), that RTVR tractors are
equipped with, falls under the definition of machinery in Article 2 (a) third indent as "an assembly
referred to in the first and second indents, ready to be installed and able to function as it stands only
if mounted on a means of transport".
A CEN/TR “Mapping between the clauses in EN 17968 and the European frameworks involving rough-
terrain variable-reach tractors” is under development.
This document is based on requirements of EN 1459-1:2025.

oSIST prEN 17968:2025
prEN 17968:2025 (E)
1 Scope
This document specifies the safety requirements relevant to load-handling functions for rough-terrain
variable reach tractors (RTVR tractors). This includes the safety requirements for their permanently
mounted equipment (PME).
Fork arms are considered to be part of the PME. RTVR tractors can also be equipped with a variety of
attachments (e.g. bale spikes, mowers, sweepers).
This document deals with all the significant hazards, hazardous situations and events relevant to the
operation of the PME of RTVR tractors when they are used as intended and under conditions of misuse
which are reasonably foreseeable by the manufacturer (see Annex A).
This document does not apply to:
— rough-terrain variable-reach trucks covered by EN 1459-1:2025;
— slewing rough-terrain variable-reach trucks covered by EN 1459-2:2015+A1:2018;
— industrial variable reach trucks covered by EN ISO 3691-2:2023;
— lorry-mounted variable-reach trucks covered by ISO 20297-1:2017;
— variable-reach trucks fitted with tilting or elevating operator position;
— mobile cranes covered by EN 13000:2010+A1:2014;
— machines designed primarily for earth moving, even if their buckets and blades are replaced with
forks (see EN 474 series);
— trucks designed primarily with variable length load suspension elements (e.g. chain, ropes) from
which the load can swing freely in all directions;
— trucks designed primarily for container handling;
— trucks on tracks;
— trucks with articulated chassis;
— front loaders covered by EN 12525:2000+A2:2010;
— attachments.
Determination and declaration of sound power level is not addressed by this document.
This document does not cover sales literature.
This document does not address hazards linked to:
— operation of the RTVR tractor from a position other than the normal operating position or the remote
control;
— hybrid power systems;
— gas power systems;
— gasoline engine systems;
oSIST prEN 17968:2025
prEN 17968:2025 (E)
— battery power systems.
This document does not address hazards which can occur:
a) when handling suspended loads which can swing freely (additional requirements are given in
EN 1459-4:2024+A1:2025);
b) when using RTVR tractors on public roads;
c) when operating in potentially explosive atmospheres (additional requirements are given in
EN 1755:2024);
d) when operating underground;
e) when towing trailers;
f) when fitted with a personnel work platform (additional requirements are given in EN 1459-3:2015
and EN 1459-9:2021);
g) when using system capable of controlling the speed of the RTVR tractor as set by the operator
(cruise-control).
This document does not provide a method of calculation for fatigue and strength of material.
This document is not applicable to RTVR tractors manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1459-5:2020, Rough-terrain trucks — Safety requirements and verification — Part 5: Attachment
interface
EN 12053:2001+A1:2008, Safety of industrial trucks — Test methods for measuring noise emissions
EN 13059:2002+A1:2008, Safety of industrial trucks — Test methods for measuring vibration
EN 15000:2008, Safety of industrial trucks — Self-propelled variable reach trucks — Specification,
performance and test requirements for longitudinal load moment indicators and longitudinal load moment
limiters
EN 15830:2012, Rough-terrain variable reach trucks — Visibility — Test methods and verification
EN 17314:2020, Industrial trucks — Specifications and test methods — Operator restraint systems other
than lap-type seat belts
EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
EN IEC 62061:2021, Safety of machinery — Functional safety of safety-related electrical, electronic and
programmable electronic control systems (IEC 62061:2021)

This document is impacted by EN 1459-5:2020/prA1:202x.
This document is impacted by the amendments EN 60529:1991/A1:2000 and EN 60529:1991/A2:2013.
oSIST prEN 17968:2025
prEN 17968:2025 (E)
EN ISO 3449:2008, Earth-moving machinery — Falling-object protective structures — Laboratory tests
and performance requirements (ISO 3449:2005)
EN ISO 3457:2008, Earth-moving machinery — Guards — Definitions and requirements (ISO 3457:2003)
EN ISO 3471:2008, Earth-moving machinery — Roll-over protective structures — Laboratory tests and
performance requirements (ISO 3471:2008)
EN ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their
components (ISO 4413:2010)
EN ISO 6683:2008, Earth-moving machinery — Seat belts and seat belt anchorages — Performance
requirements and tests (ISO 6683:2005)
EN ISO 11688-1:2009, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)
EN ISO 13849-1:2023, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design (ISO 13849-1:2023)
EN ISO 13850:2015, Safety of machinery — Emergency stop function — Principles for design
(ISO 13850:2015)
EN ISO 13857:2019, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2019)
ISO 2328:2011, Fork-lift trucks — Hook-on type fork arms and fork arm carriages — Mounting dimensions
ISO 2330:2002, Fork-lift trucks — Fork arms — Technical characteristics and testing
ISO 3864-1:2011, Graphical symbols — Safety colours and safety sign — Part 1: Design principles for safety
signs and safety markings
ISO 3864-2:2016, Graphical symbols — Safety colours and safety sign — Part 2: Design principles for
product safety labels
ISO 3864-3:2024, Graphical symbols — Safety colours and safety sign — Part 3: Design principles for
graphical symbols for use in safety signs
ISO 3864-4:2011, Graphical symbols — Safety colours and safety sign — Part 4: Colorimetric and
photometric properties of safety sign materials
ISO 5053-1:2020, Industrial trucks — Vocabulary — Part 1: Types of industrial trucks
ISO 6011:2003, Earth-moving machinery — Visual display of machine operation
ISO 7000:2019, Graphical symbols for use on equipment — Registered symbols
oSIST prEN 17968:2025
prEN 17968:2025 (E)
ISO 9244:2008 , Graphical symbols for use on equipment — Registered symbols
ISO 10263-2:2009, Earth-moving machinery — Operator enclosure environment — Part 2: Air filter
element test method
ISO 10263-4:2009, Earth-moving machinery — Operator enclosure environment — Part 4: Heating,
ventilating and air conditioning (HVAC) test method and performance
ISO 12509:2023, Earth-moving machinery and rough-terrain trucks — Lighting, signalling and marking
lights, and reflex reflectors
ISO 13333:1994, Earth-moving machinery — Dumper body support and operator's cab tilt support devices
ISO 15817:2012, Earth-moving machinery — Safety requirements for remote operator control systems
ISO 15818:2017, Earth-moving machinery — Lifting and tying-down attachment points — Performance
requirements
ISO 15870:2000, Powered industrial trucks — Safety signs and hazard pictorials — General principles
ISO 16528-1:2007, Boilers and pressure vessels — Part 1: Performance requirements
ISO 16528-2:2007, Boilers and pressure vessels — Part 2: Procedures for fulfilling the requirements of
ISO 16528-1
ISO 21507:2010, Earth-moving machinery — Performance requirements for non-metallic fuel tanks
ISO 22915-10:2023, Industrial trucks — Verification of stability — Part 10: Additional stability test for
trucks operating in the special condition of stacking with load laterally displaced by powered devices
ISO 22915-14:2010, Industrial trucks — Verification of stability — Part 14: Rough-terrain variable-reach
trucks
ISO 22915-20:2023, Industrial trucks — Verification of stability — Part 20: Additional stability test for
trucks operating in the special condition of offset load, offset by utilization
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010, ISO 5053-
1:2020 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
tractor
motorised, wheeled agricultural or forestry vehicle having two axles and a maximum design speed of not
less than 6 km/h, the main function of which lies in its tractive power and which has been especially

As impacted by ISO 9244:2008/Amd 1:2016.
oSIST prEN 17968:2025
prEN 17968:2025 (E)
designed to pull, push, carry and actuate certain interchangeable equipment designed to perform
agricultural or forestry work, or to tow agricultural or forestry trailers or equipment
[SOURCE: Regulation (EU) No 167/2013, Article 3(8), modified]
3.2
rough-terrain variable-reach tractor
RTVR tractor
tractor having one telescopic articulated arm, non-slewing or having a slewing movement of not more
than 5° either side of the longitudinal axis of the RTVR tractor used for stacking loads
Note 1 to entry: See Figure 1.

Figure 1 — RTVR tractor
3.3
compact rough-terrain variable-reach tractor
RTVR tractor having a maximum height in normal travel mode of 2 150 mm and at least one of the
following conditions:
— a maximum operating mass of 7 000 kg;
— a maximum width in normal travel mode of 2 000 mm
Note 1 to entry: These dimensions do not include equipment such as working lights, mirrors, etc.
3.4
actual capacity
Q
maximum load, established by the manufacturer based on components strength and RTVR tractor
stability, that the RTVR tractor can carry, lift and stack to a specified height, at a specified standard load
centre distance and reach, in normal operating conditions
Note 1 to entry: The actual capacity depends on the configuration of the RTVR tractor in terms of such variables as:
— lift height;
— reach of the boom;
— standard load centre distance;
oSIST prEN 17968:2025
prEN 17968:2025 (E)
— load handling device (fork arms or attachment fitted);
— stabilizing devices.
Note 2 to entry: This actual capacity defines the load handling ability of the particular RTVR tractor as equipped.
Additional actual capacity ratings with removable attachments may also be established where permitted by the
appropriate stability test or by calculation verified by empirical data.
3.5
rated capacity
Q1
maximum load permitted by the manufacturer at the standard load centre distance (D) that the RTVR
tractor is capable of lifting and transporting on fork arms in normal conditions with the boom fully
retracted
3.6
reach
d
distance between two vertical parallel planes, one plane tangent to the front of the outside diameter of
the front tyres, the other plane described by the vertical projection of the centre-of-gravity of the load to
the ground
Note 1 to entry: The centre-of-gravity of the load (G) is defined in Table 1.
Note 2 to entry: See Figure 2 for examples of reach.
Note 3 to entry: For practical matters, d can be measured referring to point g, being g the vertical projection of the
centre-of-gravity (G) of the load onto the plane of the top surface of the fork arms.
oSIST prEN 17968:2025
prEN 17968:2025 (E)
Key
d reach
D standard load centre distance
G centre of gravity of the load
g the vertical projection of the centre-of-gravity (G) of the load onto the plane of the top surface of the fork
arms
H height of the load
Q actual capacity
Q1 rated capacity
Q2 actual capacity at maximum height or elevation
Q3 actual capacity at maximum reach
Figure 2 — Parameters for the designation of the actual capacity of the RTVR tractor with fork
oSIST prEN 17968:2025
prEN 17968:2025 (E)
3.7
lift height
H
vertical distance between the upper face of the fork arms and the ground
Note to entry: See Figure 2.
3.8
standard load centre distance
D
distance from the centre of gravity (G) of the load measured horizontally back to the front of the fork
shanks and vertically down to the upper faces of the fork arms, as specified in Table 1
Note 1 to entry: See Figure 2, for example.
Note 2 to entry: Typical standard load centre distances are given in Table 1. Trucks may be rated for special
applications with load centres related to those applications which may be different from those listed in Table 1.
Table 1 — Typical standard load centre distance
Rated capacity Q in kg Standard load centre distance D in mm
400 500 600 900 1 200
0 < 1 000 X
≥ 1 000 < 5 000  X
≥ 5 000 ≤ 10 000   X
> 10 000 < 20 000   X X X
≥ 20 000 < 25 000    X X
≥ 25 000     X
3.9
axle oscillation lock
mechanism designed to prevent oscillation of an axle to improve RTVR tractor stability
3.10
stabilising devices
extendable and/or pivoting mechanical supports used to improve stability of a RTVR tractor when
stationary
3.11
lateral levelling
changing the lateral inclination angle between the chassis and the ground to ensure the boom operates
in a vertical plane even when the RTVR tractor is positioned on a side slope
3.12
forks
device comprising two or more solid fork arms, each consisting of a shank (vertical portion) and blade,
which is hook- or shaft-mounted, fitted on the carriage and usually adjusted manually
3.13
boom
pivoting support member that permits horizontal and vertical positioning of the load or attachment
oSIST prEN 17968:2025
prEN 17968:2025 (E)
3.14
crab steering mode
steering mode where all wheels of the RTVR tractor steer in the same direction
3.15
normal operating position
position specified by the manufacturer in which the operator is able to control the RTVR tractor
operations, including load handling functions
3.16
attachment bracket
device fitted at the end of the boom to mount interchangeable attachments to facilitate quick interchange
of attachment
3.17
boom float
operating mode that uses gravity to allow an attachment at the end of the boom to follow a contour (e.g.
the ground)
3.18
maximum working pressure
maximum pressure in the hydraulic circuit during normal operation
Note to entry: This definition is derived from ISO 10972-3:2003, 3.2.
3.19
level ground
ground with a gradient of (0 ± 2) %
3.20
operating mass
mass of the RTVR tractor equipped with forks, unladen, and with the operator (75 kg), full fuel tank and
all fluid systems (i.e. hydraulic oil, transmission oil, engine oil, engine coolant) at the levels specified by
the manufacturer
3.21
technically permissible maximum operating mass
operating mass without the forks and including the heaviest permitted attachment without load
3.22
operator’s station
part of the machine which surrounds the normal operating position
3.23
enclosed cab
cab where door(s) or window
...