SIST EN ISO 10350-1:2008/A1:2014
(Main)Plastics - Acquisition and presentation of comparable single- point data - Part 1: Moulding materials (ISO 10350-1:2008/Amd 1:2014)
Plastics - Acquisition and presentation of comparable single- point data - Part 1: Moulding materials (ISO 10350-1:2008/Amd 1:2014)
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1: Formmassen (ISO 10350 1:2007/Amd 1:2014)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 1: Matériaux pour moulage (ISO 10350-1:2008/Amd 1:2014)
Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 1. del: Materiali za oblikovanje - Dopolnilo A1 (ISO 10350-1:2008/Amd 1:2014)
Standard ISO 10350 določa posebne preskusne postopke za pridobitev in predstavitev primerljivih podatkov za nekatere osnovne lastnosti polimernih materialov. Na splošno vsako lastnost določa ena eksperimentalna vrednost, čeprav so v nekaterih primerih lastnosti predstavljene z dvema vrednostma, ki sta pridobljeni v različnih preskusnih pogojih. Vključene so tiste lastnosti, ki so običajno navedene v tehničnih listih proizvajalca. Ta del standarda ISO 10350 se večinoma uporablja za neojačene in ojačene plastomerne materiale in duromere, ki so lahko oblikovani z vbrizgavanjem ali s stiskanjem ali pripravljeni v obliki trakov določene debeline. 2. del standarda ISO 10350 obravnava zlasti polimerne materiale, ojačene z dolgimi vlakni ali z brezkončnimi vlakni. Za potrebe standarda ISO 10350 se za polimerne materiale, ojačene z dolgimi vlakni, štejejo polimerni materiali, katerih vlakna so pred oblikovanjem daljša od 7,5 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10350-1:2008/oprA1:2011
01-junij-2011
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO 0DWHULDOL]DREOLNRYDQMD'RSROQLOR ,62 '$PG
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials - Amendment 1 (ISO 10350-1:2008/DAmd1)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350-1:2008/DAmd1)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage - Amendement 1 (ISO 10350-1:2008/DAmd1)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2008/prA1
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 10350-1:2008/oprA1:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
EUROPEAN STANDARD
DRAFT
EN ISO 10350-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 83.080.01
English Version
Plastics - Acquisition and presentation of comparable single-
point data - Part 1: Moulding materials - Amendment 1 (ISO
10350-1:2008/DAmd1)
Plastiques - Acquisition et présentation de caractéristiques
intrinsèques comparables - Partie 1: Matériaux pour
moulage - Amendement 1 (ISO 10350-1:2008/DAmd1)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2008/prA1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
EN ISO 10350-1:2008/prA1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
EN ISO 10350-1:2008/prA1:2011 (E)
Foreword
This document (EN ISO 10350-1:2008/prA1:2011) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by
NBN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 10350-1:2008/DAmd1 has been approved by CEN as a EN ISO 10350-1:2008/prA1:2011
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10350-1:2008/oprA1:2011
DRAFT AMENDMENT ISO 10350-1:2007/DAM 1
ISO/TC 61/SC 2 Secretariat: AENOR
Voting begins on Voting terminates on
2011-04-14 2011-09-14
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NORMALISATION
Plastics — Acquisition and presentation of comparable
single-point data —
Part 1:
Moulding materials
AMENDMENT 1
Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables —
Partie 1: Matériaux pour moulage
AMENDEMENT 1
ICS 83.080.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will
...
SLOVENSKI STANDARD
SIST EN ISO 10350-1:2008/A1:2014
01-september-2014
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO 0DWHULDOL]DREOLNRYDQMH'RSROQLOR$ ,62 $PG
Plastics - Acquisition and presentation of comparable single- point data - Part 1:
Moulding materials (ISO 10350-1:2008/Amd 1:2014)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350 1:2007/Amd 1:2014)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO 10350-1:2008/Amd 1:2014)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2008/A1:2014
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 10350-1:2008/A1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10350-1:2008/A1:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 10350-1:2008/A1:2014
EUROPEAN STANDARD
EN ISO 10350-1:2008/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 83.080.01
English Version
Plastics - Acquisition and presentation of comparable single-
point data - Part 1: Moulding materials (ISO 10350-1:2008/Amd
1:2014)
Plastiques - Acquisition et présentation de caractéristiques Kunststoffe - Ermittlung und Darstellung vergleichbarer
intrinsèques comparables - Partie 1: Matériaux pour Einpunktkennwerte - Teil 1: Formmassen (ISO 10350
moulage - (ISO 10350-1:2008/Amd 1:2014) 1:2007/Amd 1:2014)
This amendment A1 modifies the European Standard EN ISO 10350-1:2008; it was approved by CEN on 30 April 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2008/A1:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10350-1:2008/A1:2014
EN ISO 10350-1:2008/A1:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10350-1:2008/A1:2014
EN ISO 10350-1:2008/A1:2014 (E)
Foreword
This document (EN ISO 10350-1:2008/A1:2014) has been prepared by Technical Committee ISO/TC 61
“Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by
NBN.
This Amendment to the European Standard EN ISO 10350-1:2008 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and
conflicting national standards shall be withdrawn at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10350-1:2007/Amd 1:2014 has been approved by CEN as EN ISO 10350-1:2008/A1:2014
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.