EN ISO 10350-1:2017
(Main)Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1: Formmassen (ISO 10350-1:2017)
Die Reihe ISO 10350 legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte für bestimmte grundlegende Eigenschaften von Kunststoffen fest. Im Allgemeinen wird jede Eigen¬schaft durch einen einzelnen Messwert festgelegt, in bestimmten Fällen wird eine Eigenschaft jedoch durch zwei Werte charakterisiert, die unter verschiedenen Prüfbedingungen ermittelt wurden. Die aufgeführten Eigenschaften werden vom Hersteller üblicherweise in Datenblättern erfasst. Dieser Teil der Reihe ISO 10350 behandelt in erster Linie thermoplastische und duroplastische Kunststoffe mit oder ohne Verstärkung, die spritzgegossen, gepresst oder in Form von Platten mit festgelegter Dicke bereitgestellt werden. ISO 10350 2 befasst sich speziell mit Kunststoffen, die eine Verstärkung durch lange oder kontinuierliche Fasern haben. Für die Anwendung von ISO 10350 gelten solche Kunststoffe als langfaserverstärkt, die vor dem Formen eine Faserlänge von mehr als 7,5 mm haben.
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 1: Matériaux pour moulage (ISO 10350-1:2017)
L'ISO 10350 identifie des méthodes d'essai spécifiques en vue de l'acquisition et de la présentation de données comparables relatives à certaines propriétés de base des matières plastiques. En général, chaque propriété est spécifiée par une valeur expérimentale unique; toutefois, dans certains cas, certaines propriétés sont représentées par deux valeurs obtenues dans des conditions d'essai différentes. Les propriétés indiquées sont celles qui sont traditionnellement présentées dans les fiches techniques des fabricants. L'ISO 10350-1 est avant tout applicable aux matériaux thermodurcissables ou thermoplastiques, renforcés ou non, susceptibles d'être moulés par compression ou injection ou préparés en feuilles ayant une épaisseur spécifiée. Pour les besoins du présent document, il est à noter que les plastiques renforcés de fibres longues ont des longueurs de fibre supérieures à 7,5 mm avant moulage.
NOTE L'ISO 10350‑2 traite spécifiquement des plastiques renforcés de fibres longues ou continues.
Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 1. del: Materiali za oblikovanje (ISO 10350-1:2017)
Skupina standardov ISO 10350 določa posebne preskusne postopke za pridobitev in predstavitev primerljivih podatkov o določenih osnovnih lastnostih polimernih materialov. Na splošno vsako lastnost določa enotna eksperimentalna vrednost, čeprav so v nekaterih primerih lastnosti predstavljene z dvema vrednostma, ki sta pridobljeni pri različnih preskusnih pogojih. Vključene so tiste lastnosti, ki so običajno navedene v tehničnih listih proizvajalca. Ta dokument se večinoma uporablja za neojačene in ojačene plastomerne materiale in duromere, ki so lahko oblikovani z vbrizgavanjem ali stiskanjem oziroma so pripravljeni v obliki trakov določene debeline. Za potrebe tega dokumenta se za polimerne materiale, ojačene z dolgimi vlakni, šteje, da so njihova vlakna pred oblikovanjem daljša od 7,5 mm.
OPOMBA: Standard ISO 10350-2 obravnava zlasti z dolgimi ali neprekinjenimi vlakni ojačene polimerne materiale.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2018
1DGRPHãþD
SIST EN ISO 10350-1:2008
SIST EN ISO 10350-1:2008/A1:2014
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO 0DWHULDOL]DREOLNRYDQMH ,62
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials (ISO 10350-1:2017)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350-1:2017)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO 10350-1:2017)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2017
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10350-1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 10350-1:2008
English Version
Plastics - Acquisition and presentation of comparable
single-point data - Part 1: Moulding materials (ISO 10350-
1:2017)
Plastiques - Acquisition et présentation de Kunststoffe - Ermittlung und Darstellung
caractéristiques intrinsèques comparables - Partie 1: vergleichbarer Einpunktkennwerte - Teil 1:
Matériaux pour moulage (ISO 10350-1:2017) Formmassen (ISO 10350-1:2017)
This European Standard was approved by CEN on 10 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10350-1:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics”
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10350-1:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10350-1:2017 has been approved by CEN as EN ISO 10350-1:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 10350-1
Third edition
2017-09
Plastics — Acquisition and
presentation of comparable single-
point data —
Part 1:
Moulding materials
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 1: Matériaux pour moulage
Reference number
ISO 10350-1:2017(E)
©
ISO 2017
ISO 10350-1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 10350-1:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Specimen preparation and conditioning. 3
5 Test requirements . 4
6 Presentation of results . 4
Bibliography .11
ISO 10350-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical behavior.
This third edition cancels and replaces the second edition (ISO 10350-1:2007), which has been
technically revised. It also incorporates the Amendment ISO 10350-1:2007/Amd.1:2014.
A list of all parts in the ISO 10350 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
ISO 10350-1:2017(E)
Introduction
The ISO 10350 series has been prepared because users of plastics find that available data cannot always
be readily used to compare the properties of similar materials, especially when the data have been
supplied by different sources. Even when the same standard tests have been used, they often allow
the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this document is to identify specific methods and conditions of test to be
used for the acquisition and presentation of data in order that valid comparisons between materials
can be made.
The ISO 10350 series is concerned with tests employed to present “single-point” data on the limited
range of properties commonly included in data sheets and used for the preliminary selection of
materials. Such data represent the most basic approach to the specification of properties of materials,
and the ISO 10350 series thus facilitates the first steps towards more efficient selection and use of
plastics in the many applications to which they are suited.
Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3) are concerned
with the standardized acquisition and presentation of multipoint data, to demonstrate how properties
vary with important factors such as time, temperature and the presence of particular natural and
chemical environments. In these documents, some additional properties are included. Their use will
provide a more substantial database than one containing only single-point data, and so will enable
improved assessment of the fitness of a material for any particular application. In addition, ISO 11403-1,
which deals with mechanical properties, assists predictions of the performance of components and
ISO 11403-2, covering thermal and processing properties, aids predictions of melt-flow behaviour
during manufacturing. ISO 11403-3 is concerned with environmental influences on properties, and
other parts may be prepared to cover additional properties.
INTERNATIONAL STANDARD ISO 10350-1:2017(E)
Plastics — Acquisition and presentation of comparable
single-point data —
Part 1:
Moulding materials
1 Scope
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of
comparable data for certain basic properties of plastics. In general, each property is specified by a single
experimental value, although in certain cases properties are represented by two values obtained under
different test conditions. The properties included are those presented conventionally in manufacturers'
data sheets. This document applies predominantly to unreinforced and reinforced thermoplastic and
thermosetting materials that may be injection- or compression-moulded or prepared as sheets of
specified thickness. For the purposes of this document, long-fibre-reinforced plastics are considered to
have fibre lengths greater than 7,5 mm prior to moulding.
NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplast
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.