Intelligent transport systems - ESafety - ECall end to end conformance testing for IMS packet switched based systems

This document defines the key actors in the eCall chain of service provision using IMS over packet switched networks (such as LTE/4G) as:
1)   In-vehicle system (3.20) (IVS)/vehicle,
2)   Mobile network Operator (MNO),
3)   Public safety answering point (3.27) (PSAP),
and to provide conformance tests for actor groups 1) - 3).
NOTE 1   Conformance tests are not appropriate nor required for vehicle occupants (3.36), although they are the recipient of the service.
NOTE 2   Third party eCall systems (TPS eCall) are not within the scope of this deliverable. This is because the core TPS-eCall (3.32) standard (EN 16102) does not specify the communications link between the vehicle and the TPS service provider (3.29).
NOTE 3   These conformance tests are based on the appropriate conformance tests from EN 16454 which was published before Internet Protocol multimedia Systems (IMS) packet switched networks were available. This deliverable therefore replicates the appropriate tests from EN 16454 (and acknowledge their source); adapt and revise Conformance Test Protocols (CTP) from EN 16454 to an IMS paradigm; or provide new additional tests that are required for the IMS paradigm. Some 14 112-eCall (Pan European eCall) tests provided in EN 16454 are specific to GSM/UMTS circuit switched communications and not appropriate for the IMS paradigm and are therefore excluded from this deliverable.
This document therefore provides a suite of ALL conformance tests for IVS equipment, MNO’s, and PSAPS, required to ensure and demonstrate compliance to FprCEN/TS 17184.
NOTE 4   Because in the event of non-viability or non-existence of an IMS supporting network at any particular time/location, IMS-eCall systems revert to CS networked eCall systems eCall via GSM/UMTS, IVS and PSAPs need to support, and prove compliance to both IMS and CS switched networks.
The Scope covers conformance testing (and approval) of new engineering developments, products and systems, and does not imply testing associated with individual installations in vehicles or locations.

Intelligente Verkehrssysteme - eSicherheit - eCall Ende-zu-Ende Konformitätsprüfungen für IMS-paketvermittelnde Systeme

Systèmes de transport intelligents - eSécurité - eCall: Essais de conformité du système « eCall » de bout en bout pour les systèmes IMS basés sur la commutation de paquets

Inteligentni transportni sistemi - e-Varnost - Preskušanje skladnosti e-klica v zvezi pošiljatelj-prejemnik za paketno preklopne sisteme IMS

Ta dokument opredeljuje ključne udeležence v verigi e-klica pri izvajanju storitve z uporabo sistema IMS prek paketno preklopnih omrežij (kot je LTE/4G) kot:
1) avtomobilski sistem (3.20) (IVS)/vozilo,
2) operaterje mobilnih omrežij (MNO),
3) odzivno točko javne varnosti (3.27) (PSAP),
in zagotavlja preskuse skladnosti za skupine udeležencev 1) – 3).
OPOMBA 1: Preskusi skladnosti niso primerni in zahtevani za potnike v vozilu (3.36), čeprav so prejemniki storitve.
OPOMBA 2: Sistemi za e-klice tretje strani (e-klic TPS) ne spadajo na področje uporabe tega dokumenta. Temeljni standard o sistemih za e-klice tretje strani (3.32) (EN 16102) namreč ne določa komunikacijske povezave med vozilom in ponudnikom storitev sistema tretje strani (3.29).
OPOMBA 3: Ti preskusi skladnosti temeljijo na ustreznih preskusih skladnosti iz standarda EN 16454, ki je bil objavljen, preden so bila na voljo paketno preklopna omrežja z multimedijskim sistemom internetnega protokola (IMS). Ta dokument tako vključuje ustrezne preskuse iz standarda EN 16454 (in navaja njihov vir); prilagaja in revidira protokole za preskuse skladnosti (CTP) iz standarda 16454 paradigmi IMS; ali zagotavlja nove dodatne preskuse, ki so zahtevani za paradigmo IMS. 14 preskusov 112-e-klica (vseevropski elektronski klic v sili), podanih v standardu EN 16454, je značilnih za vodovno komutirano komunikacijo in niso ustrezni za paradigmo IMS, zaradi česar so izključeni iz tega dokumenta.
Ta dokument tako določa paket VSEH preskusov skladnosti za opremo IVS, operaterja mobilnega omrežja in PSAPS, ki so zahtevani za zagotavljanje in prikaz skladnosti s standardom FprCEN/TS 17184.
OPOMBA 4: Ker v primeru neuspešnega delovanja ali neobstoja omrežja, ki podpira IMS, ob katerem koli času/na kateri koli lokaciji sistemi za e-klice IMS preidejo na sisteme za e-klice v vodovno komutiranem omrežju prek omrežja GSM/UMTS, morata IVS in odzivna točka javne varnosti podpreti in zagotoviti skladnosti z omrežjem IMS ter vodovno komutiranim omrežjem.
Področje uporabe zajema preskuse skladnosti (in potrditev) novih inženirskih dosežkov, izdelkov in sistemov ter ne zahteva preskusov, povezanih s posameznimi vgradnjami v vozila ali na lokacije.

General Information

Status
Published
Publication Date
09-Dec-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
20-Nov-2018
Due Date
25-Jan-2019
Completion Date
10-Dec-2018

Buy Standard

Technical specification
TS CEN/TS 17240:2019 - BARVE
English language
124 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 17240:2019
01-januar-2019
Inteligentni transportni sistemi - e-Varnost - Preskušanje skladnosti e-klica v zvezi
pošiljatelj-prejemnik za paketno preklopne sisteme IMS
Intelligent transport systems - ESafety - ECall end to end conformance testing for IMS
packet switched based systems
Intelligente Verkehrssysteme - eSicherheit - eCall Ende-zu-Ende Konformitätsprüfungen
für IMS-paketvermittelnde Systeme
Systèmes de transport intelligents - eSécurité - eCall: Essais de conformité du système «
eCall » de bout en bout pour les systèmes IMS basés sur la commutation de paquets
Ta slovenski standard je istoveten z: CEN/TS 17240:2018
ICS:
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
SIST-TS CEN/TS 17240:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 17240:2019

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 17240:2019


CEN/TS 17240
TECHNICAL SPECIFICATION

SPÉCIFICATION TECHNIQUE

October 2018
TECHNISCHE SPEZIFIKATION
ICS 35.240.60
English Version

Intelligent transport systems - ESafety - ECall end to end
conformance testing for IMS packet switched based
systems
Systèmes de transport intelligents - eSécurité - eCall: Intelligente Verkehrssysteme - eSicherheit - eCall
Essais de conformité du système " eCall " de bout en Ende-zu-Ende Konformitätsprüfungen für IMS-
bout pour les systèmes IMS basés sur la commutation paketvermittelnde Systeme
de paquets
This Technical Specification (CEN/TS) was approved by CEN on 20 August 2018 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 17240:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 17240:2019
CEN/TS 17240:2018 (E)
Contents Page
European foreword . 7
Introduction . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Symbols and abbreviations . 15
5 Conformance . 16
5.1 General . 16
5.2 General conditions . 16
6 General overview of the eCall transaction for pan-European eCall . 16
7 How to use this Standard . 21
7.1 Layout and procedures . 21
7.2 System under test . 22
7.3 Accelerated test procedures . 22
7.4 Accelerated test procedures for IVSs . 23
7.4.1 Accelerated test procedures for all types of 112-eCall IVS . 23
7.4.2 Additional accelerated test procedures for 112-eCall only IVS . 24
7.5 Accelerated test procedures for MNOs . 25
7.6 Accelerated test procedures for PSAPs – 112-eCall . 25
8 Requirements . 27
8.1 Requirements - General objectives . 27
8.1.1 State transitions. 27
8.1.2 Classification of testing . 33
8.1.3 CTP naming conventions . 35
8.1.4 CTP naming convention for IVS conformance tests . 36
8.2 CTP structure . 36
9 Conformance test requirements for in-vehicle IMS user equipment and systems
(IVS). 38
9.1 Conformance test requirements for in-vehicle user equipment and systems for IMS-
eCall (112-eCall/Pan European eCall) . 38
9.2 Test objectives and purposes . 38
9.3 Classification of testing and referenced tests for in-vehicle user equipment for 112-
eCall (Pan European eCall) IVS . 38
9.3.1 Taxonomy of testing . 38
9.3.2 Referenced tests . 38
9.4 State transition conformance tests for in-vehicle equipment and system to comply to
Standards for 112-eCall (Pan European eCall) . 39
9.4.1 Conformance requirement . 39
9.4.2 Use case test objectives by stage . 39
9.4.3 CTP 1.1.0.1IMS — Conformance to ETSI TS 136 523 and ETSI TS 134 229 – 112-eCall
IVS via IMS . 42
9.4.4 CTP 1.1.0.2 — Test for conformance to valid SIM/USIM – 112-eCall . 42
2

---------------------- Page: 4 ----------------------

SIST-TS CEN/TS 17240:2019
CEN/TS 17240:2018 (E)
9.4.5 CTP 1.1.0.3 — Automatic eCall triggering does not occur when engine control OFF –
112-eCall IVS . 43
9.4.6 CTP 1.1.1.1 — Power on and self test – 112-eCall IVS . 44
9.4.7 CTP 1.1.2.1 — Test for automatic activation of eCall . 45
9.4.8 CTP 1.1.2.2 — Automatically triggered eCall in progress was not disconnected upon
a new eCall trigger – 112-eCall IVS . 46
9.4.9 CTP 1.1.2.3 — Post-Lateral-crash performance of automatic trigger – IVS . 47
9.4.10 CTP 1.1.2.4 — Post-frontal-crash performance of automatic trigger - IVS . 48
9.4.11 CTP 1.1.2.5 — Performance of automatic trigger – Different crash types . 49
9.4.12 CTP 1.1.3.1 — eCall manually activated – 112-eCall IVS . 50
9.4.13 CTP 1.1.3.2 — Manually triggered eCall in progress was not disconnected upon a
new eCall trigger – 112-eCall IVS . 51
9.4.14 CTP 1.1.4.1 — Test eCall activated – 112-eCall IVS . 52
9.4.15 CTP 1.1.5.1 — Network registration – 112-eCall IVS . 53
9.4.16 CTP 1.1.5.2 — Manual termination of eCall by vehicle occupants not allowed
(automatically triggered eCall) – 112-eCall IVS . 54
9.4.17 CTP 1.1.5.3 — Manual termination of eCall by vehicle occupants not allowed
(manually triggered eCall) – 112-eCall IVS . 55
9.4.18 CTP 1.1.5.4 — Automatically triggered eCall in progress was not disconnected when
ignition is switched to OFF – 112-eCall IVS . 56
9.4.19 CTP 1.1.5.5 — Manually triggered eCall in progress was not disconnected when
engine control is switched to OFF – 112-eCall IVS . 57
9.4.20 CTP 1.1.5.6-IMS — Priority over conflicting communication – 112-eCall IVS . 58
9.4.21 CTP 1.1.5.7 — Network registration is re-tried when network registration attempt
was not successful – 112-eCall IVS . 59
9.4.22 CTP 1.1.6.1-IMS — SIP Invite sent . 59
9.4.23 CTP 1.1.7.1-IMS — Establish session with urn:service:sos.ecall.automatic – 112-eCall
IVS . 60
9.4.24 CTP 1.1.8.1-IMS — Establish session with urn:service:sos.ecall.manual – 112-eCall
IVS . 61
9.4.25 CTP 1.1.9.1-IMS — Set-up call to test address – 112-eCall IVS . 62
9.4.26 CTP 1.1.10.1-IMS — eCall is attempted when no networks are available (limited
service condition) – 112-eCall IVS . 63
9.4.27 CTP 1.1.10.2-IMS — Re-dial attempt completed within 2 min after eCall is dropped –
112-eCall IVS . 63
9.4.28 CTP 1.1.10.3 –IMS — ALLOW ACK Received . 63
9.4.29 CTP 1.1.15.1-IMS — Voice link Established – 112-eCall IVS . 64
9.4.30 CTP 1.1.15.2-IMS — Verify MSD Received – 112-eCall IVS . 65
9.4.31 CTP 1.1.16.1 — Clear down call automatically – PE eCall IVS . 65
9.4.32 CTP 1.1.16.2-IMS — IVS clears down the eCall upon T2 expiry – 112-eCall IVS . 66
9.4.33 CTP 1.1.16.3-IMS — IVS registers recent eCalls – 112-eCall IVS . 67
9.4.34 CTP 1.1.17.1-IMS — Call-back allowed and able to be answered by IVS – 112-eCall IVS . 68
9.4.35 CTP 1.1.17.2-IMS — Call-back answered by IVS in the event of abnormal termination
– 112-eCall IVS . 69
9.4.36 CTP 1.1.17.3-IMS — MSD transfer occurs upon PSAP request during call-back – 112-
eCall IVS . 70
9.4.37 CTP 1.1.17.4-IMS — Remain registered for ≥ 1 hr – 112-eCall IVS . 71
9.5 State transition test scripts for in-vehicle equipment and system to comply to
Standards for 112-eCall (Pan European eCall) – additional tests for eCall only
systems . 71
9.5.1 General . 71
9.5.2 CTP 1.1.1.2-IMS — IVS does not perform registration after power-up – 112-eCall only
IVS . 73
3

---------------------- Page: 5 ----------------------

SIST-TS CEN/TS 17240:2019
CEN/TS 17240:2018 (E)
9.5.3 CTP 1.1.1.3-IMS — IVS periodically scans and maintains a list of available PLMNs –
112-eCall only . 73
9.5.4 CTP1.1.10.4 — Verify that PLMN registration procedure is executed upon initiating
an eCall – 112-eCall only IVS . 74
9.5.5 CTP 1.1.17.5-IMS — Remain registered for ≥ 1 hr ≤ 12 hr – 112-eCall only IVS . 75
10 Conformance tests for mobile network operators . 75
10.1 Test objectives and purposes . 75
10.1.1 General . 75
10.1.2 Default assumptions . 76
10.2 Taxonomy of testing and referenced tests . 76
10.3 Use case conformance tests for mobile network operator systems to comply to
Standards for 112-eCall (Pan European eCall) . 76
10.3.1 Conformance requirement . 76
10.3.2 Use case test objectives by stage . 76
10.4 State transition test scripts for mobile network operators to demonstrate
compliance with 112-eCall (Pan European eCall) standards . 77
10.4.1 General . 77
10.4.2 CTP 2.0.1 — Keep SIMs/USIMs alive even though not in regular operation – MNO . 79
10.4.3 CTP 2.0.2-IMS — MNO supports general eCall relevant requirements . 80
10.4.4 CTP 2.0.3 — Decommission SIM/USIM - MNO . 81
10.4.5 CTP 2.0.4-IMS — Support IMS-eCall routing – MNO . 81
10.4.6 CTP 2.1.1 — Accept registration – Home network – MNO . 82
10.4.7 CTP 2.1.2 — Accept registration – Roaming –MNO . 82
10.4.8 CTP 2.2.1.1-IMS — Establish IMS-eCall (automatically initiated) – MNO . 83
10.4.9 CTP 2.2.1.2-IMS — Route call to ‘most appropriate’ PSAP – MNO . 84
10.4.10 CTP 2.2.1.3-IMS — Provide IMS emergency data/caller ID – MNO . 85
10.4.11 CTP 2.2.2.1-IMS — Receive IMS-eCall (manual initiated) – MNO . 86
10.4.12 CTP 2.2.3.1-IMS — Test for receiving test eCall . 86
10.4.13 CTP 2.2.3.2 — Route call to non-emergency number – MNO . 86
10.4.14 CTP 2.2.3.3 — Provide CLI for test eCall – MNO. 87
10.4.15 CTP 2.3.1 — Call in progress–MNO . 87
10.4.16 CTP 2.5.1 — Support call-back – MNO . 88
10.4.17 CTP 2.6.1 — Maintain registration for 1-12 h – MNO . 88
10.4.18 CTP 2.7.1 — Maintain call records - MNO . 88
11 Conformance tests for PSAP systems . 88
11.1 Test objectives and purposes . 88
11.2 Taxonomy of testing and referenced tests . 89
11.2.1 Taxonomy of testing . 89
11.2.2 Referenced tests . 89
11.3 Use case conformance tests for PSAP systems to comply to Standards for 112-eCall
(Pan European eCall) . 89
11.3.1 Conformance requirement . 89
11.3.2 Use case test objectives by stage . 89
11.4 State transition conformance tests for PSAPs – 112-eCall . 90
11.4.1 General . 90
11.4.2 CTP 3.1.0.1-IMS — Provide MNOs with appropriate routing data – Member State/
PSAP IMS-eCall . 92
11.4.3 CTP 3.1.0.2 — Maintain map geo-information – PSAP IMS-eCall . 93
11.4.4 CTP 3.1.1.1-IMS — Receive automatically initiated eCall – PSAP IMS-eCall . 94
11.4.5 CTP 3.1.1.2-IMS — Receive manually initiated eCall – PSAP IMS-eCall . 95
11.4.6 CTP 3.1.2-IMS — Interpret IMS emergency data- Caller ID and location – PSAP IMS-
eCall . 96
11.4.7 CTP 3.1.3.2-IMS — PSAP equipment failure – PSAP IMS-eCall . 96
4

---------------------- Page: 6 ----------------------

SIST-TS CEN/TS 17240:2019
CEN/TS 17240:2018 (E)
11.4.8 CTP 3.1.5.2-IMS — Route to operator after T4 expiration – PSAP 112-eCall . 96
11.4.9 CTP 3.1.7.1-IMS — Receive MSD – PSAP IMS-eCall . 97
11.4.10 CTP 3.1.7.2-IMS — Verify status bit in AL-ACK upon positive ACK– PSAP 112-
eCall . 98
11.4.11 CTP 3.1.7.4-IMS — Verify transfer of corrupted MSD – PSAP IMS-eCall . 98
11.4.12 CTP 3.1.7.5-IMS — Verify PSAP behaviour when MSD format check fails– PSAP
IMS-eCall . 99
11.4.13 CTP 3.1.8 — ACK – PSAP IMS-eCall . 99
11.4.14 CTP 3.1.9-IMS — Route voice and MSD to operator – PSAP IMS-eCall . 100
11.4.15 CTP 3.1.10-IMS — Display IMS-eCall data and MSD to operator – PSAP IMS-eCall . 101
11.4.16 CTP 3.1.11-IMS — Decode VIN – PSAP IMS-eCall . 102
11.4.17 CTP 3.1.12-IMS — Talk to vehicle occupants – PSAP IMS-eCall . 103
11.4.18 CTP 3.1.13-IMS — Request new MSD before call cleardown – PSAP IMS-eCall . 104
11.4.19 CTP 3.1.14.1 — Call cleardown – PSAP IMS-eCall . 105
11.4.20 CTP 3.1.14.2-IMS — Verify status bit in AL-ACK upon cleardown - PSAP –112-
eCall . 105
106
11.4.21 CTP 3.1.15-IMS — Call-back to vehicle – PSAP 112-eCall .
11.4.22 CTP 3.1.16-IMS — Request new MSD after call cleardown – PSAP IMS-eCall . 107
12 Marking, labelling and packaging . 107
13 Declaration of patents and intellectual property . 108
Annex A (normative) Proforma conformance test report for 112-eCall (Pan European eCall)
in-vehicle system (IVS) . 109
A.1 Conformance test report . 109
A.1.1 System under test: . . 109
A.1.2 System under test identification . 109
A.1.3 Testing environment . 110
A.1.4 Limits and reservation . 110
A.1.5 Comments . 110
A.2 SUT conformance status . 110
A.3 Static conformance summary . 111
A.4 Dynamic conformance summary . 111
A.5 Static conformance review report . 111
A.6 Test campaign report . 112
A.7 Observations . 113
Annex B (normative) ProForma conformance test report for mobile network operator
(MNO) . 114
B.1 Conformance test report . 114
B.1.1 System under test: . . 114
B.1.2 System under test identification . 114
B.1.3 Testing environment . 115
B.1.4 Limits and reservation . 115
B.1.5 Comments . 115
B.2 SUT conformance status . 115
B.3 Static conformance summary . 116
B.4 Dynamic conformance summary . 116
B.5 Static conformance review report . 116
B.6 Test campaign report . 117
B.7 Observations . 117
Annex C (normative) ProForma conformance test report for public service answering point
(PSAP) .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.