SIST EN 16392-2:2014

Non Destructive Testing - Characterisation and verification of ultrasonic phased array systems - Part 2: Probes

EN 16392-2 covers linear phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz - 10 MHz. This European Standard specifies the characterisation tests that have to be done at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria. This document does not describe methods and acceptance criteria to characterise the performance of an ultrasonic phased array instrument or the performance of a combined system. These are described in prEN ISO 18563-1 and in prEN ISO 18563-3.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe

Dieses Dokument gilt für die zerstörungsfreie Prüfung mit Ultraschall unter Anwendung von Linearprüfköpfen mit phasengesteuerter Elementanordnung (Phased Array Prüfköpfen), die entweder für die Kontakttechnik (mit oder ohne Vorsatzkeil) oder für die Tauchtechnik vorgesehen sind und Mittenfrequenzen von 0,5 MHz bis 10 MHz anwenden.
Dieses  Dokument legt Fertigungsendprüfungen an Phased Array Prüfköpfen fest, deren Ergebnisse zur Charakterisierung der Prüfköpfe dienen. Es werden sowohl die Methodologie als auch Zulässigkeitskriterien festgelegt.
Es sollte beachtet werden, dass die genannten Zulässigkeitskriterien nur unter den Bedingungen gültig sind, die für den jeweils betrachteten Prüfkopf festgelegt wurden.
Die Verfahren und Zulässigkeitskriterien, die in diesem Dokument beschrieben werden, sind nicht zur Charakterisierung der Leistung kompletter Phased Array Prüfsysteme anwendbar.

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle multi-élément par ultrasons - Partie 2: Traducteurs

Le présent document traite des traducteurs multi-éléments linéaires utilisés pour le contrôle non destructif par ultrasons, au contact (avec ou sans sabot) ou en immersion, ayant une fréquence centrale comprise entre 0,5 MHz et 10 MHz.
Le présent document spécifie les essais de caractérisation qui doivent être effectués à l'issue de la fabrication d'un traducteur multi-élément. Il définit à la fois la méthodologie et les critères d'acceptation.
Il convient de noter que ces critères d'acceptation sont seulement valables dans les conditions définies pour le traducteur considéré.
Le présent document ne décrit pas les méthodes et critères d'acceptation permettant de caractériser les performances d'un appareillage complet de contrôle multi-élément par ultrasons.

Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme faznih sistemov - 2. del: Sonde

Standard EN 16392-2 zajema sonde linearnega faznega niza, ki se uporabljajo za ultrazvočne neporušitvene preiskave pri tehniki s kontaktom (z ali brez klina) ali pri imerzni tehniki z osrednjimi frekvencami v razponu od 0,5 MHz do 10 MHz. Ta evropski standard določa preizkuse za karakterizacijo, ki morajo biti izvedeni na koncu izdelave sonde linearnega faznega niza. Opredeljuje tako metodologijo kot kriterije sprejemljivosti. Ta dokument ne opisuje metod in kriterijev sprejemljivosti za karakterizacijo delovanja ultrazvočnega instrumenta faznega niza ali delovanja kombiniranega sistema. Ti so opisani v standardih prEN ISO 18563-1 in prEN ISO 18563-3.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 30-May-2012
• Publication Date: 29-Jun-2014
• Withdrawal Date: 22-Oct-2017
• ICS: 19.100 - Non-destructive testing
• Technical Committee: PKG - Testing of metallic materials
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 20-Oct-2017
• Due Date: 12-Nov-2017
• Completion Date: 23-Oct-2017
• Ref Project: EN 16392-2:2014 - Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes

Relations

• Replaced By: SIST EN ISO 18563-2:2017 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)
• Effective Date: 06-Sep-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: PrüfköpfeEssais non destructifs - Caractérisation et vérification de l'appareillage de contrôle multi-élément par ultrasons - Partie 2: TraducteursNon Destructive Testing - Characterisation and verification of ultrasonic phased array systems - Part 2: Probes19.100Neporušitveno preskušanjeNon-destructive testingICS:Ta slovenski standard je istoveten z:EN 16392-2:2014SIST EN 16392-2:2014en,fr,de01-julij-2014SIST EN 16392-2:2014SLOVENSKI
STANDARD



SIST EN 16392-2:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16392-2
March 2014 ICS 19.100 English Version
Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe This European Standard was approved by CEN on 6 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16392-2:2014 ESIST EN 16392-2:2014



EN 16392-2:2014 (E)
2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 General requirements for compliance .4 5 Technical specification for phased array probes .5 6 Test equipment .7 7 Performance tests for phased array probes .7
SIST EN 16392-2:2014



EN 16392-2:2014 (E) 3 Foreword This document (EN 16392-2:2014) has been prepared by Technical Committee CEN/TC 138 “Non-destructive testing”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. EN 16392 consists of the following parts, under the general title Non-destructive testing — Characterisation and verification of ultrasonic phased array equipment: — Part 2: Probes; and prEN ISO 18563 — Part 1: Instruments; — Part 3: Combined systems. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 16392-2:2014



EN 16392-2:2014 (E)
4
1 Scope This European Standard covers linear phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz – 10 MHz. This European Standard specifies the characterisation tests that have to be done at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria. This document does not describe methods and acceptance criteria to characterise the performance of an ultrasonic phased array instrument or the performance of a combined system. These are described in prEN ISO 18563-1 and in prEN ISO 18563-3. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16018, Non-destructive testing - Terminology - Terms used in ultrasonic testing with phased arrays EN 1330-2, Non-destructive testing - Terminology - Part 2: Terms common to the non-destructive testing methods. EN 1330-4, Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing EN ISO 2400, Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 1 (ISO 2400:2012) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1330-2, EN 1330-4, EN 16018 and the following apply. 3.1 phased array probe data sheet document describing the general characteristics of the same type of phased array probes 3.2 phased array probe certificate document showing compliance with this European Standard giving the measured values of the required parameters of one specific phased array probe 4 General requirements for compliance An ultrasonic phased array probe complies with this document if it satisfies the following conditions: a) the probe shall comply with Clause 7; b) a declaration of conformity is issued: SIST EN 16392-2:2014



EN 16392-2:2014 (E) 5 1) either based on the results of statistical analysis by a manufacturer operating a certified quality management system or by an organisation operating an accredited test laboratory; 2) or based on measurements of every probe. Probe manufacturers shall then provide the measurement results. Manufacturers shall state which method is used. c) the probe body shall show: 1) a unique serial number; 2) the centre frequency; 3) the number of elements; 4) the pitch; 5) the position of the first and last element; 6) reference, if applicable. If this information cannot be given on the probe body, then at least a unique serial number and a reference to identify the probe shall be used. d) a technical specification for the probe is available, which defines the performance criteria in accordance with Clause 5. 5 Technical specification for phased array probes The technical specifications of phased array probes required by this document shall be listed in a data sheet. Table 1 shows the information which shall be supplied by the manufacturer in the probe data sheet (M = Measurement, OI = Other information). The probe data sheet sh
...