SIST EN IEC 63182-4:2022
(Main)Magnetic powder cores - guidelines on dimensions and the limits of surface irregularities - Part 4: Block-cores
Magnetic powder cores - guidelines on dimensions and the limits of surface irregularities - Part 4: Block-cores
This part of IEC 63182 specifies the preferred range of the dimensions that are important for mechanical interchangeability and the guidelines on allowable limits of surface irregularities for block-cores made of metallic magnetic powder.
This document is a specification about surface irregularities which is useful in the negotiations between suppliers and users of magnetic powder core.
The use of "derived" standards which give more detailed specifications of component parts while still permitting compliance with this standard is discussed in Annex A.
Magnetpulverkerne – Richtlinien zu Maßen und Grenzen von Oberflächenbeschädigungen – Teil 4: Blockkerne
Noyaux en poudre magnétique - Lignes directrices concernant les dimensions et les limites des irrégularités de surface - Partie 4: Noyaux en blocs
L’IEC 63182-4:2021 spécifie la plage préférentielle des dimensions qui sont importantes pour l’interchangeabilité mécanique, ainsi que les lignes directrices concernant les limites admissibles des irrégularités de surface pour les noyaux en blocs en poudre magnétique métallique.
Le présent document est une spécification portant sur les irrégularités de surface, qui est utile pour les négociations entre les fournisseurs et les utilisateurs de noyaux en poudre magnétique.
Jedra iz magnetnega prahu - Smernice o merah in mejnih vrednostih površinskih nepravilnosti - 4. del: Blokovna jedra
Ta del standarda IEC 63182 določa prednostni razpon mer, ki so pomembne za mehansko medsebojno zamenljivost, in smernice o dovoljenih mejnih vrednostih površinskih nepravilnosti za blokovna jedra, izdelana iz kovinskega magnetnega prahu.
Ta dokument je specifikacija o površinskih nepravilnostih, ki je uporabna za sklepanje dogovorov med dobavitelji in uporabniki jeder iz magnetnega prahu.
Uporaba »izpeljanih« standardov, ki podajajo podrobnejše specifikacije o delih komponent in hkrati dovoljujejo skladnost s tem standardom, je obravnavana v dodatku A.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 63182-4:2022
01-marec-2022
Jedra iz magnetnega prahu - Smernice o merah in mejnih vrednostih površinskih
nepravilnosti - 4. del: Blokovna jedra
Magnetic powder cores - guidelines on dimensions and the limits of surface irregularities
- Part 4: Block-cores
Noyaux en poudre magnétique - Lignes directrices concernant les dimensions et les
limites des irrégularités de surface - Partie 4: Noyaux en blocs
Ta slovenski standard je istoveten z: EN IEC 63182-4:2022
ICS:
29.100.10 Magnetne komponente Magnetic components
SIST EN IEC 63182-4:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 63182-4:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 63182-4:2022
EUROPEAN STANDARD EN IEC 63182-4
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2022
ICS 29.100.10
English Version
Magnetic powder cores - Guidelines on dimensions and the
limits of surface irregularities - Part 4: Block-cores
(IEC 63182-4:2021)
Noyaux en poudre magnétique - Lignes directrices Magnetpulverkerne - Richtlinien zu Maßen und Grenzen
concernant les dimensions et les limites des irrégularités de von Oberflächenbeschädigungen - Teil 4: Blockkerne
surface - Partie 4: Noyaux en blocs (IEC 63182-4:2021)
(IEC 63182-4:2021)
This European Standard was approved by CENELEC on 2022-01-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63182-4:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 63182-4:2022
EN IEC 63182-4:2022 (E)
European foreword
The text of document 51/1373/CDV, future edition 1 of IEC 63182-4, prepared by IEC/TC 51
"Magnetic components, ferrite and magnetic powder materials" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 63182-4:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-10-03
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-01-03
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63182-4:2021 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 63182-4:2022
EN IEC 63182-4:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 63182-1 - Magnetic powder cores - Guidelines on EN IEC 63182-1 -
dimensions and the limits of surface
irregularities - Part 1: General specification
3
---------------------- Page: 5 ----------------------
SIST EN IEC 63182-4:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 63182-4:2022
IEC 63182-4
®
Edition 1.0 2021-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic powder cores – Guidelines on dimensions and the limits of surface
irregularities –
Part 4: Block-cores
Noyaux en poudre magnétique – Lignes directrices concernant les dimensions
et les limites des irrégularités de surface –
Partie 4: Noyaux en blocs
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.100.10 ISBN 978-2-8322-1054-9
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 63182-4:2022
– 2 – IEC 63182-4:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Primary dimensions . 5
5 Limits of surface irregularities . 6
5.1 Definition of surface irregularities . 6
5.2 Examples of surface irregularities . 7
5.3 Chips and ragged edges . 7
5.3.1 General . 7
5.3.2 Chips . 7
5.3.3 Ragged edges . 7
5.4 Cracks . 7
5.5 Flash . 7
5.6 Rust . 8
5.7 Discoloration . 8
Annex A (normative) Derived standards . 9
Figure 1 – Main dimensions of block-cores . 6
Figure 2 – Examples of surface irregularities . 7
Table 1 – Main dimensions of block-cores. 6
---------------------- Page: 8 ----------------------
SIST EN IEC 63182-4:2022
IEC 63182-4:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MAGNETIC POWDER CORES – GUIDELINES ON DIMENSIONS
AND THE LIMITS OF SURFACE IRREGULARITIES –
Part 4: Block-cores
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommend
...
SLOVENSKI STANDARD
oSIST prEN IEC 63182-4:2021
01-september-2021
Jedra iz magnetnega prahu - Smernice o merah in mejnih vrednostih površinskih
nepravilnosti - 4. del: Blokovna jedra
Magnetic powder cores - guidelines on dimensions and the limits of surface irregularities
- Part 4: Block-cores
Noyaux en poudre magnétique - Lignes directrices concernant les dimensions et les
limites des irrégularités de surface - Partie 4: Noyaux en blocs
Ta slovenski standard je istoveten z: prEN IEC 63182-4:2021
ICS:
29.100.10 Magnetne komponente Magnetic components
oSIST prEN IEC 63182-4:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 63182-4:2021
---------------------- Page: 2 ----------------------
oSIST prEN IEC 63182-4:2021
51/1373/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 63182-4 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2021-06-11 2021-09-03
SUPERSEDES DOCUMENTS:
51/1344/CD, 51/1354/CC
IEC TC 51 : MAGNETIC COMPONENTS, FERRITE AND MAGNETIC POWDER MATERIALS
SECRETARIAT: SECRETARY:
Japan Mr Takeshi Abe
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any,
in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for
Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they
are aware and to provide supporting documentation.
TITLE:
Magnetic powder cores – guidelines on dimensions and the limits of surface irregularities–
Part 4: Block-cores
PROPOSED STABILITY DATE: 2027
NOTE FROM TC/SC OFFICERS:
Copyright © 2021 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 63182-4:2021
63182-4/Ed.1/CDV©IEC(E) 2 51/1373/CDV
1 CONTENTS
2 FOREWORD . 3
3 1 Scope . 5
4 2 Normative references . 5
5 3 Terms and definitions . 5
6 4 Primary dimensions . 5
7 5 Limits of surface irregularities . 6
8 5.1 Definition of surface irregularities . 6
9 5.2 Examples of surface irregularities . 6
10 5.3 Chips and Ragged edges . 7
11 5.3.1 General . 7
12 5.3.2 Chips . 7
13 5.3.3 Ragged edges . 7
14 5.4 Cracks . 7
15 5.5 Flash . 7
16 5.6 Rust . 7
17 5.7 Discoloration . 7
18 Annex A (normative) Derived standards . 8
19 Figure 1 – Main dimensions of block-cores . 5
20 Figure 2 – Examples of surface irregularities . 7
21 Table 1 – Main dimensions of block-cores . 6
---------------------- Page: 4 ----------------------
oSIST prEN IEC 63182-4:2021
51/1373/CDV 3 63182-4/Ed.1/CDV©IEC(E)
22 INTERNATIONAL ELECTROTECHNICAL COMMISSION
23
24 MAGNETIC POWDER CORES – GUIDELINES ON DIMENSIONS
25 AND THE LIMITS OF SURFACE IRREGULARITIES –
26 Part 4: Block-cores
27 FOREWORD
28 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
29 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
30 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
31 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
32 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
33 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
34 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
35 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
36 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
37 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
38 consensus of opinion on the relevant subjects since each technical committee has representation from all
39 interested IEC National Committees.
40 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
41 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
42 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
43 misinterpretation by any end user.
44 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
45 transparently to the maximum extent possible in their national and regional publications. Any divergence between
46 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
47 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
48 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
49 services carried out by independent certification bodies.
50 6) All users should ensure that they have the latest edition of this publication.
51 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
52 members of its technical committees and IEC National Committees for any personal injury, property damage or
53 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
54 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
55 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
56 indispensable for the correct application of this publication.
57 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
58 rights. IEC shall not be held responsible for identifying any or all such patent rights.
59 IEC 63182-4 has been prepared by IEC technical committee 51
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.