SIST EN ISO 3927:2004
(Main)Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO 3927:2001)
Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO 3927:2001)
Metallpulver, mit Ausnahme von Hartmetallpulvern -Bestimmung der Verdichtbarkeit bei einachsigem Pressen (ISO 3927:2001)
Diese Internationale Norm legt Verfahren zur Bestimmung der Verdichtbarkeit eines metallischen Pulvers bei ein-
achsigem Pressen in einer geschlossenen Matrize unter festgelegten Bedingungen fest.
Das Verfahren ist nicht auf Hartmetallpulver anwendbar.
Poudres métalliques, a l'exclusion des poudres pour métaux-durs - Détermination de la compressibilité sous compression uniaxiale (ISO 3927:2001)
La présente Norme internationale spécifie des méthodes de mesure de l'aptitude d'une poudre métallique à être comprimée lorsqu'elle est soumise dans une matrice à une charge de compression uniaxiale dans des conditions déterminées. La méthode n'est pas applicable aux poudres pour métaux-durs.
Kovinski praški brez praškov za trdine – Določanje stisljivosti z enoosno kompresijo (ISO 3927:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3927:2004
01-september-2004
.RYLQVNLSUDãNLEUH]SUDãNRY]DWUGLQH±'RORþDQMHVWLVOMLYRVWL]HQRRVQR
NRPSUHVLMR ,62
Metallic powders, excluding powders for hardmetals - Determination of compressibility in
uniaxial compression (ISO 3927:2001)
Metallpulver, mit Ausnahme von Hartmetallpulvern -Bestimmung
der Verdichtbarkeit bei einachsigem Pressen (ISO
3927:2001)
Poudres métalliques, a l'exclusion des poudres pour métaux-durs - Détermination de la
compressibilité sous compression uniaxiale (ISO 3927:2001)
Ta slovenski standard je istoveten z: EN ISO 3927:2001
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 3927:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3927:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 3927:2004
EUROPEAN STANDARD
EN ISO 3927
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 77.160 Supersedes EN 23927:1993
English version
Metallic powders, excluding powders for hardmetals -
Determination of compressibility in uniaxial compression (ISO
3927:2001)
Poudres métalliques, à l'exclusion des poudres pour Metallpulver, mit Ausnahme von Hartmetallpulvern -
métaux-durs - Détermination de la compressibilité sous Bestimmung der Verdichtbarkeit bei einachsigem Pressen
compression uniaxiale (ISO 3927:2001) (ISO 3927:2001)
This European Standard was approved by CEN on 1 December 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3927:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3927:2004
EN ISO 3927:2001 (E)
CORRECTED 2002-01-30
Foreword
The text of the International Standard ISO 3927:2001 has been prepared by Technical
Committee ISO/TC 119 "Powder metallurgy", the secretariat of which is held by CMC.
This document supersedes EN 23927:1993.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2002, and conflicting national
standards shall be withdrawn at the latest by June 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 3927:2001 was approved by CEN as a European
Standard without any modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3927:2004
INTERNATIONAL ISO
STANDARD 3927
Third edition
2001-12-01
Metallic powders, excluding powders for
hardmetals — Determination of
compressibility in uniaxial compression
Poudres métalliques, à l'exclusion des poudres pour métaux-durs —
Détermination de la compressibilité sous compression uniaxiale
Reference number
ISO 3927:2001(E)
©
ISO 2001
---------------------- Page: 5 ----------------------
SIST EN ISO 3927:2004
ISO 3927:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2001 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 3927:2004
ISO 3927:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO3927 was prepared by Technical Committee ISO/TC119, Powder metallurgy,
Subcommittee SC 2, Sampling and testing methods for powders (including powders for hardmetals).
This third edition cancels and replaces the second edition (ISO 3927:1985), which has been technically revised.
©
ISO 2001 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 3927:2004
---------------------- Page: 8 ----------------------
SIST EN ISO 3927:2004
INTERNATIONAL STANDARD ISO 3927:2001(E)
Metallic powders, excluding powders for hardmetals —
Determination of compressibility in uniaxial compression
1 Scope
This International Standard specifies methods for measuring the extent to which a metallic powder is compacted
when subjected to uniaxial compressive loading in a confining die under specified conditions.
The method is not applicable to powders for hardmetals.
2Symbols
For the purposes of this International Standard, the symbols given in Table 1 apply.
Table 1 —
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.