SIST EN ISO 3927:2012
(Main)Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO 3927:2011)
Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO 3927:2011)
ISO 3927:2011 specifies methods for measuring the extent to which a metallic powder is compacted when subjected to uniaxial compressive loading in a confining die under specified conditions.
The method is not applicable to powders for hardmetals.
Metallpulver, mit Ausnahme von Hartmetallpulvern - Bestimmung der Verdichtbarkeit bei einachsigem Pressen (ISO 3927:2011)
Diese Internationale Norm legt Verfahren zur Bestimmung der Verdichtbarkeit eines metallischen Pulvers bei einachsigem Pressen in einer geschlossenen Matrize unter festgelegten Bedingungen fest. Das Verfahren ist nicht auf Hartmetallpulver anwendbar.
Poudres métalliques, à l'exclusion des poudres pour métaux-durs - Détermination de la compressibilité sous compression uniaxiale (ISO 3927:2011)
L'ISO 3927:2011 spécifie des méthodes de mesure de l'aptitude d'une poudre métallique à être comprimée lorsqu'elle est soumise dans une matrice à une charge de compression uniaxiale dans des conditions déterminées.
La méthode ne s'applique pas aux poudres pour métaux-durs.
Kovinski praški razen praškov za trdine - Ugotavljanje stisljivosti z enoosno kompresijo (ISO 3927:2011)
Ta mednarodni standard določa metodo za merjenje obsega, do katerega se kovinski prašek stisne, ko se nanj v omejevalni matrici izvaja enoosna kompresijska obremenitev pod natančno določenimi pogoji. Metoda ne velja za praške za trdine.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3927:2012
01-januar-2012
1DGRPHãþD
SIST EN ISO 3927:2004
SIST EN ISO 3927:2004/AC:2009
Kovinski praški razen praškov za trdine - Ugotavljanje stisljivosti z enoosno
kompresijo (ISO 3927:2011)
Metallic powders, excluding powders for hardmetals - Determination of compressibility in
uniaxial compression (ISO 3927:2011)
Metallpulver, mit Ausnahme von Hartmetallpulvern - Bestimmung der Verdichtbarkeit bei
einachsigem Pressen (ISO 3927:2011)
Poudres métalliques, à l'exclusion des poudres pour métaux-durs - Détermination de la
compressibilité sous compression uniaxiale (ISO 3927:2011)
Ta slovenski standard je istoveten z: EN ISO 3927:2011
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 3927:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3927:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 3927:2012
EUROPEAN STANDARD
EN ISO 3927
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2011
ICS 77.160 Supersedes EN ISO 3927:2001
English Version
Metallic powders, excluding powders for hardmetals -
Determination of compressibility in uniaxial compression (ISO
3927:2011)
Poudres métalliques, à l'exclusion des poudres pour Metallpulver, mit Ausnahme von Hartmetallpulvern -
métaux-durs - Détermination de la compressibilité sous Bestimmung der Verdichtbarkeit bei einachsigem Pressen
compression uniaxiale (ISO 3927:2011) (ISO 3927:2011)
This European Standard was approved by CEN on 10 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3927:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3927:2012
EN ISO 3927:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3927:2012
EN ISO 3927:2011 (E)
Foreword
This document (EN ISO 3927:2011) has been prepared by Technical Committee ISO/TC 119 "Powder
metallurgy" in collaboration with Technical Committee CEN/TC SS M11 “Powder metallurgy” the secretariat of
which is held by CCMC.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at
the latest by August 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3927:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3927:2011 has been approved by CEN as a EN ISO 3927:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 3927:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 3927:2012
INTERNATIONAL ISO
STANDARD 3927
Fourth edition
2011-02-01
Metallic powders, excluding powders for
hardmetals — Determination of
compressibility in uniaxial compression
Poudres métalliques, à l'exclusion des poudres pour métaux-durs —
Détermination de la compressibilité sous compression uniaxiale
Reference number
ISO 3927:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 3927:2012
ISO 3927:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3927:2012
ISO 3927:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3927 was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 2,
Sampling and testing methods for powders (including powders for hardmetals).
This fourth edition cancels and replaces the third edition (ISO 3927:2001), of which it constitutes a minor
revision. It incorporates ISO 3927:2001/Cor.1:2008, with the following changes.
⎯ Clause 8, Title: Footnote 1 has been deleted.
⎯ Subclause 8.1: The original text was replaced with a new paragraph.
⎯ Subclauses 8.1 and 8.2 have been renumbered as 8.2 and 8.3.
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 3927:2012
---------------------- Page: 10 ----------------------
SIST EN ISO 3927:2012
INTERNATIONAL STANDARD ISO 3927:2011(E)
Metallic powders, excluding powders for hardmetals —
Determination of compressibility in uniaxial compression
1 Scope
This International Standard specifies methods for m
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Metallpulver, mit Ausnahme von Hartmetallpulvern - Bestimmung der Verdichtbarkeit bei einachsigem Pressen (ISO/FDIS 3927:2010)Poudres métalliques, à l'exclusion des poudres pour métaux-durs - Détermination de la compressibilité sous compression uniaxiale (ISO/FDIS 3927:2010)Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO/FDIS 3927:2010)77.160Metalurgija prahovPowder metallurgyICS:Ta slovenski standard je istoveten z:FprEN ISO 3927kSIST FprEN ISO 3927:2010en,fr,de01-december-2010kSIST FprEN ISO 3927:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 3927:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 3927
September 2010 ICS 77.160 Will supersede EN ISO 3927:2001English Version
Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression (ISO/FDIS 3927:2010)
Poudres métalliques, à l'exclusion des poudres pour métaux-durs - Détermination de la compressibilité sous compression uniaxiale (ISO/FDIS 3927:2010)
Metallpulver, mit Ausnahme von Hartmetallpulvern - Bestimmung der Verdichtbarkeit bei einachsigem Pressen (ISO/FDIS 3927:2010) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/SS M11.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 3927:2010: EkSIST FprEN ISO 3927:2010
FprEN ISO 3927:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 3927:2010
FprEN ISO 3927:2010 (E) 3 Foreword This document (FprEN ISO 3927:2010) has been prepared by Technical Committee ISO/TC 119/SC 2 "Sampling and testing methods for powders (including powders for hardmetals)" in collaboration with Technical Committee CEN/TC SS M11 “Powder metallurgy” the secretariat of which is held by CCMC. This document is currently submitted to the parallel Unique Acceptance Procedure. This document will supersede EN ISO 3927:2001. Endorsement notice The text of ISO/FDIS 3927:2010 has been approved by CEN as a FprEN ISO 3927:2010 without any modification.
kSIST FprEN ISO 3927:2010
kSIST FprEN ISO 3927:2010
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TOSUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORT-ING DOCUMENTATION. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-LOGICAL, COMMERCIAL AND USER PURPOSES,DRAFT INTERNATIONAL STANDARDS MAY ONOCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STAN-DARDS TO WHICH REFERENCE MAY BE MADE INNATIONAL REGULATIONS.
Reference numberISO/FDIS 3927:2010(E)© ISO 2010 FINAL DRAFT ISO/TC 119/SC 2 Secretariat: SIS Voting begins on: 2010-09-09 Voting terminates on: 2010-11-09
INTERNATIONAL STANDARD ISO/FDIS3927Metallic powders, excluding powders for hardmetals — Determination of compressibility in uniaxial compression Poudres métalliques, à l'exclusion des poudres pour métaux-durs — Détermination de la compressibilité sous compression uniaxiale
kSIST FprEN ISO 3927:2010
ISO/FDIS 3927:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted.
ii © ISO 2010 – All rights reserved
kSIST FprEN ISO 3927:2010
ISO/FDIS 3927:2010(E) © ISO 2010 – All rights reserved iii ISO/CEN PARALLEL PROCESSING This Minor Revision has been developed within the International Organization for Standardization (ISO), and processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. This final draft is hereby submitted to a parallel two-month approval vote in ISO and three-month UAP vote in CEN. Positive votes shall not be accompanied by comments. Negative votes shall be accompanied by the relevant technical reasons.
kSIST FprEN ISO 3927:2010
ISO/FDIS 3927:2010(E) iv © ISO 2010 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3927 was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 2, Sampling and testing methods for powders (including powders for hardmetals). This fourth edition cancels and replaces the third edition (ISO 3927:2001), of which it constitutes a minor revision. It incorporates ISO 3927:2001/Cor.1:2008, with the following changes. ⎯ Clause 8, Title: Footnote 1 has been deleted. ⎯ Subclause 8.1: The original text was
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.