SIST EN 13523-25:2022
(Main)Coil coated metals - Test methods - Part 25: Resistance to humidity
Coil coated metals - Test methods - Part 25: Resistance to humidity
This Part of EN 13523 specifies a procedure for evaluating the humidity resistance of an organic coating (coil coating) on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.
Bandbeschichtete Metalle - Prüfverfahren - Teil 25: Beständigkeit gegen Feuchte
Dieses Dokument legt ein Verfahren zum Bestimmen der Beständigkeit einer organischen Beschichtung auf einem metallischen Substrat gegen Feuchte durch Beanspruchung in einer Feuchtekammer unter kontrollierten Bedingungen fest.
Tôles prélaquées - Méthodes d'essai - Partie 25: Résistance à l'humidité
Le présent document décrit un mode opératoire permettant d’évaluer la résistance à l’humidité d’un revêtement organique déposé sur un subjectile métallique, via l’exposition dans une enceinte à atmosphère humide dans des conditions contrôlées.
Prevlečene kovine, ki se navijajo - Preskusne metode - 25. del: Odpornost proti vlagi
Ta del standarda EN 13523 določa postopek za vrednotenje odpornosti proti vlagi organske prevleke (prevleke kovin, ki se navijajo) na kovinski podlagi pri izpostavljenosti vlažnosti pod nadzorovanimi pogoji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13523-25:2022
01-september-2022
Nadomešča:
SIST EN 13523-25:2014
Prevlečene kovine, ki se navijajo - Preskusne metode - 25. del: Odpornost proti
vlagi
Coil coated metals - Test methods - Part 25: Resistance to humidity
Bandbeschichtete Metalle - Prüfverfahren - Teil 25: Beständigkeit gegen Feuchte
Tôles prélaquées - Méthodes d'essai - Partie 25: Résistance à l'humidité
Ta slovenski standard je istoveten z: EN 13523-25:2022
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-25:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13523-25:2022
---------------------- Page: 2 ----------------------
SIST EN 13523-25:2022
EN 13523-25
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2022
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-25:2014
English Version
Coil coated metals - Test methods - Part 25: Resistance to
humidity
Tôles prélaquées - Méthodes d'essai - Partie 25 : Bandbeschichtete Metalle - Prüfverfahren - Teil 25:
Résistance à l'humidité Beständigkeit gegen Feuchte
This European Standard was approved by CEN on 19 December 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-25:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13523-25:2022
EN 13523-25:2022 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus . 6
6 Materials . 6
7 Sampling . 6
8 Test panels . 6
9 Procedure. 6
9.1 Preparation . 6
9.2 Exposure in humidity cabinet . 8
9.3 Evaluation . 8
9.3.1 General . 8
9.3.2 Overall surface (flat surface of the panel) . 8
9.3.3 Edges, scribes and bends (as applicable) . 8
10 Expression of results . 9
11 Precision . 9
12 Test report . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
SIST EN 13523-25:2022
EN 13523-25:2022 (E)
European foreword
This document (EN 13523-25:2022) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall be
withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-25:2014.
The main changes are:
a) EN ISO 3696 has been added to 6.1 as reference for the deionised water;
b) a remark concerning the assessment of organic coated steel substrates having multiple metallic
phases in zinc based coating has been added to Clause 10;
c) the list of the existing parts of EN 13523 has been updated;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
3
---------------------- Page: 5 ----------------------
SIST EN 13523-25:2022
EN 13523-25:2022 (E)
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 13523-25:2022
EN 13523-25:2022 (E)
1 Scope
This document specifies a procedure for evaluating the resistance to humidity of an organic coating on a
metallic substrate, by means of exposure in a humidity cabinet under controlle
...
SLOVENSKI STANDARD
oSIST prEN 13523-25:2020
01-november-2020
Prevlečene kovine, ki se navijajo - Preskusne metode - 25. del: Odpornost proti
vlagi
Coil coated metals - Test methods - Part 25: Resistance to humidity
Bandbeschichtete Metalle - Prüfverfahren - Teil 25: Beständigkeit gegen Feuchte
Tôles prélaquées - Méthodes d'essai - Partie 25: Résistance à l'humidité
Ta slovenski standard je istoveten z: prEN 13523-25
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-25:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-25:2020
---------------------- Page: 2 ----------------------
oSIST prEN 13523-25:2020
DRAFT
EUROPEAN STANDARD
prEN 13523-25
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2020
ICS 25.220.60 Will supersede EN 13523-25:2014
English Version
Coil coated metals - Test methods - Part 25: Resistance to
humidity
Tôles prélaquées - Méthodes d'essai - Partie 25: Bandbeschichtete Metalle - Prüfverfahren - Teil 25:
Résistance à l'humidité Beständigkeit gegen Feuchte
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-25:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-25:2020
prEN 13523-25:2020 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure. 6
8.1 Preparation . 6
8.2 Exposure in humidity cabinet . 8
8.3 Evaluation . 8
8.3.1 General . 8
8.3.2 Overall surface (flat surface of the panel) . 8
8.3.3 Edges, scribes and bends (as applicable) . 8
9 Expression of results . 9
10 Precision . 9
11 Test report . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-25:2020
prEN 13523-25:2020 (E)
European foreword
This document (prEN 13523-25:2020) has been prepared by Technical Committee CEN/TC 139 “Paints
and varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-25:2014.
The main changes are:
a) ISO 3696 has been added to 5.3 as reference for the deionized water;
b) a remark concerning the assessment of Zn/Al/Mg-coated steel substrates has been added to
Clause 9;
c) the list of the existing parts of EN 13523 has been updated;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
3
---------------------- Page: 5 ----------------------
oSIST prEN 13523-25:2020
prEN 13523-25:2020 (E)
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
4
---------------------- Page: 6 ----------------------
oSIST prEN 13523-25:2020
prEN 13523-25:2020 (E)
1 Scope
This document specifies a procedure for evaluating the resistance to humidity of an organic coating on a
metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 13523-0, Coil coated metals — Test methods — Part 0: General introduction
ISO 3696:1987
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.