Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification

This International Standard specifies requirements for five types of textile-reinforced hydraulic hose
and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic
fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to
+60 °C or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures
ranging from −40 °C to +100 °C.
This International Standard does not include requirements for end fittings. It is limited to requirements
for hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish
compatibility of the hose with the fluid to be used.

Tuyaux et flexibles en caoutchouc - Types hydrauliques avec armature de textile pour fluides à base d'huile ou à base d'eau - Spécifications

Gumene cevi in cevni priključki - S tekstilom ojačene hidravlične cevi za tekočine na oljni ali vodni osnovi - Specifikacija

Ta mednarodni standard določa zahteve za pet vrst s tekstilom ojačenih hidravličnih cevi in cevnih priključkov z nazivno velikostjo od 5 do 100. Primerni so za uporabo s hidravličnimi tekočinami na vodni osnovi HFC, HFAE, HFAS in HFB, kot je opredeljeno v standardu ISO 6743-4, pri temperaturah od –40 °C do 60 °C ter za uporabo s hidravličnimi tekočinami na oljni osnovi HH, HL, HM, HR in HV, kot je opredeljeno v standardu ISO 6743-4, pri temperaturah od –40 °C do 100 °C.
Ta mednarodni standard ne vključuje zahtev za končnike. Omejen je na zahteve
za cevi in cevne priključke.
OPOMBA: Uporabnik mora po posvetovanju s proizvajalcem cevi določiti združljivost cevi z uporabljeno tekočino.

General Information

Status
Withdrawn
Publication Date
04-Apr-2016
Withdrawal Date
09-Jun-2020
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
10-Jun-2020
Due Date
03-Jul-2020
Completion Date
10-Jun-2020

Relations

Buy Standard

Standard
ISO 4079:2016
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 4079:2015 - Rubber hoses and hose assemblies -- Textile-reinforced hydraulic types for oil-based or water-based fluids -- Specification
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 4079:2016
01-maj-2016
1DGRPHãþD
SIST ISO 4079:2015
*XPHQHFHYLLQFHYQLSULNOMXþNL6WHNVWLORPRMDþHQHKLGUDYOLþQHFHYL]DWHNRþLQH
QDROMQLDOLYRGQLRVQRYL6SHFLILNDFLMD
Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or
water-based fluids - Specification
Tuyaux et flexibles en caoutchouc - Types hydrauliques avec armature de textile pour
fluides à base d'huile ou à base d'eau - Spécifications
Ta slovenski standard je istoveten z: ISO 4079:2015
ICS:
83.140.40 Gumene cevi Hoses
SIST ISO 4079:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 4079:2016

---------------------- Page: 2 ----------------------

SIST ISO 4079:2016
INTERNATIONAL ISO
STANDARD 4079
Fourth edition
2015-11-01
Rubber hoses and hose assemblies —
Textile-reinforced hydraulic types
for oil-based or water-based fluids —
Specification
Tuyaux et flexibles en caoutchouc — Types hydrauliques avec
armature de textile pour fluides à base d’huile ou à base d’eau —
Spécifications
Reference number
ISO 4079:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

SIST ISO 4079:2016
ISO 4079:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 4079:2016
ISO 4079:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 2
5 Materials and construction . 2
5.1 Hoses . 2
5.2 Hose assemblies . 2
6 Dimensions . 2
6.1 Hose diameters and hose concentricity . 2
6.2 Length . 4
7 Performance requirements . 4
7.1 General . 4
7.2 Hydrostatic requirements . 4
7.3 Minimum bend radius . 5
7.4 Resistance to impulse . 6
7.4.1 Water-based fluids . 6
7.4.2 Oil-based fluids. 6
7.4.3 Optional impulse test . 7
7.5 Leakage of hose assemblies . 7
7.6 Cold flexibility . 7
7.7 Adhesion between components . 7
7.8 Vacuum resistance . 8
7.9 Fluid resistance . 8
7.9.1 Test pieces . 8
7.9.2 Oil resistance . 8
7.9.3 Water resistance . . . 8
7.10 Ozone resistance. 8
7.11 Visual examination . 9
8 Marking . 9
8.1 Hoses . 9
8.2 Hose assemblies . 9
Annex A (normative) Type and routine testing of production hoses .10
Annex B (informative) Periodic testing of production hose .11
Annex C (informative) Recommendations for lengths of supplied hoses and tolerances on
lengths of hose assemblies .12
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 4079:2016
ISO 4079:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 4079:2009), of which it constitutes a
minor revision.
iv © ISO 2015 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 4079:2016
INTERNATIONAL STANDARD ISO 4079:2015(E)
Rubber hoses and hose assemblies — Textile-reinforced
hydraulic types for oil-based or water-based fluids —
Specification
1 Scope
This International Standard specifies requirements for five types of textile-reinforced hydraulic hose
and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic
fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to
+60 °C or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures
ranging from −40 °C to +100 °C.
This International Standard does not include requirements for end fittings. It is limited to requirements
for hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish
compatibility of the hose with the fluid to be used.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods
ISO 6743-4, Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H
(Hydraulic systems)
ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum
ISO 7326:2006, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8033:2006, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1:
Bending tests at ambient temperature
ISO 10619-2:2011, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness —
Part 2: Bending tests at sub-ambient temperatures
© ISO 2015 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 4079:2016
ISO 4079:2015(E)

3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
4 Classification
Five types of hose are specified, distinguished by their construction, working pressure and
minimum bend radius:
— Type 1TE: hoses with a single braid of textile reinforcement.
— Type 2TE: hoses with one or more braid(s) of textile reinforcement.
— Type 3TE: hoses with one or more braid(s) of textile reinforcement (higher working pressure).
— Type R3: hoses with two braids of textile reinforcement.
— Type R6: hoses with a single braid of textile reinforcement.
NOTE Type 1TE is not subjected to the impulse or vacuum resistance tests. Type R3 is not subjected to the
vacuum resistance test. Type R6 is not subjected to the impulse or vacuum resistance tests.
5 Materials and construction
5.1 Hoses
Hoses shall consist of a rubber lining that is resistant to water- and oil-based hydraulic fluids, one or
more layers of suitable textile yarn and a weather- and oil-resistant rubber cover.
Hoses shall be designed to enable end fittings to be assembled without removal of the cover.
5.2 Hose assemblies
Hose assemblies shall be manufactured only with those hose fittings whose functionality has been
verified in accordance with 7.2, 7.4, 7.5 and 7.6. The manufacturer’s instructions shall be followed for
the preparation and fabrication of hose assemblies.
6 Dimensions
6.1 Hose diameters and hose concentricity
When measured in accordance with ISO 4671, the inside and outside diameters of hoses shall conform
to the values given in Table 1.
When measured in accordance with ISO 4671, the concentricity of hoses shall conform to the values
given in Table 2.
2 © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST ISO 4079:2016
ISO 4079:2015(E)

© ISO 2015 – All rights reserved 3
Table 1 — Dimensions of hoses
Inside diameter Outside diameter
mm mm
Nominal
Types 1TE, 2TE,
a
size
Type R6 Type R3 Type 1TE Type 2TE Type 3TE Type R6 Type R3
b
3TE
min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
5 4,4 5,2 4,2 5,4 4,5 5,4 10,0 11,6 11,0 12,6 12,0 13,6 10,3 11,9 11,9 13,5
6,3 5,9 6,9 5,6 7,2 6,1 7,0 11,6 13,2 12,6 14,2 13,6 15,2 11,9 13,5 13,5 15,1
8 7,4 8,4 7,2
8,8 7,6 8,5 13,1 14,7 14,1 15,7 16,1 17,7 13,5 15,1 16,7 18,3
10 9,0 10,0 8,7 10,3 9,2 10,1 14,7 16,3 15,7 17,3 17,7 19,3 15,1 16,7 18,3 19,8
12,5 12,1 13,3 11,9 13,5 12,4 13,5 17,7 19,7 18,7 20,7 20,7 22,7 19,0 20,6 23,0 24,6
16 15,3
...

INTERNATIONAL ISO
STANDARD 4079
Fourth edition
2015-11-01
Rubber hoses and hose assemblies —
Textile-reinforced hydraulic types
for oil-based or water-based fluids —
Specification
Tuyaux et flexibles en caoutchouc — Types hydrauliques avec
armature de textile pour fluides à base d’huile ou à base d’eau —
Spécifications
Reference number
ISO 4079:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 4079:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4079:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 2
5 Materials and construction . 2
5.1 Hoses . 2
5.2 Hose assemblies . 2
6 Dimensions . 2
6.1 Hose diameters and hose concentricity . 2
6.2 Length . 4
7 Performance requirements . 4
7.1 General . 4
7.2 Hydrostatic requirements . 4
7.3 Minimum bend radius . 5
7.4 Resistance to impulse . 6
7.4.1 Water-based fluids . 6
7.4.2 Oil-based fluids. 6
7.4.3 Optional impulse test . 7
7.5 Leakage of hose assemblies . 7
7.6 Cold flexibility . 7
7.7 Adhesion between components . 7
7.8 Vacuum resistance . 8
7.9 Fluid resistance . 8
7.9.1 Test pieces . 8
7.9.2 Oil resistance . 8
7.9.3 Water resistance . . . 8
7.10 Ozone resistance. 8
7.11 Visual examination . 9
8 Marking . 9
8.1 Hoses . 9
8.2 Hose assemblies . 9
Annex A (normative) Type and routine testing of production hoses .10
Annex B (informative) Periodic testing of production hose .11
Annex C (informative) Recommendations for lengths of supplied hoses and tolerances on
lengths of hose assemblies .12
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 4079:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 4079:2009), of which it constitutes a
minor revision.
iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 4079:2015(E)
Rubber hoses and hose assemblies — Textile-reinforced
hydraulic types for oil-based or water-based fluids —
Specification
1 Scope
This International Standard specifies requirements for five types of textile-reinforced hydraulic hose
and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic
fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to
+60 °C or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures
ranging from −40 °C to +100 °C.
This International Standard does not include requirements for end fittings. It is limited to requirements
for hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish
compatibility of the hose with the fluid to be used.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods
ISO 6743-4, Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H
(Hydraulic systems)
ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum
ISO 7326:2006, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8033:2006, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1:
Bending tests at ambient temperature
ISO 10619-2:2011, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness —
Part 2: Bending tests at sub-ambient temperatures
© ISO 2015 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 4079:2015(E)

3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
4 Classification
Five types of hose are specified, distinguished by their construction, working pressure and
minimum bend radius:
— Type 1TE: hoses with a single braid of textile reinforcement.
— Type 2TE: hoses with one or more braid(s) of textile reinforcement.
— Type 3TE: hoses with one or more braid(s) of textile reinforcement (higher working pressure).
— Type R3: hoses with two braids of textile reinforcement.
— Type R6: hoses with a single braid of textile reinforcement.
NOTE Type 1TE is not subjected to the impulse or vacuum resistance tests. Type R3 is not subjected to the
vacuum resistance test. Type R6 is not subjected to the impulse or vacuum resistance tests.
5 Materials and construction
5.1 Hoses
Hoses shall consist of a rubber lining that is resistant to water- and oil-based hydraulic fluids, one or
more layers of suitable textile yarn and a weather- and oil-resistant rubber cover.
Hoses shall be designed to enable end fittings to be assembled without removal of the cover.
5.2 Hose assemblies
Hose assemblies shall be manufactured only with those hose fittings whose functionality has been
verified in accordance with 7.2, 7.4, 7.5 and 7.6. The manufacturer’s instructions shall be followed for
the preparation and fabrication of hose assemblies.
6 Dimensions
6.1 Hose diameters and hose concentricity
When measured in accordance with ISO 4671, the inside and outside diameters of hoses shall conform
to the values given in Table 1.
When measured in accordance with ISO 4671, the concentricity of hoses shall conform to the values
given in Table 2.
2 © ISO 2015 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 4079:2015(E)

© ISO 2015 – All rights reserved 3
Table 1 — Dimensions of hoses
Inside diameter Outside diameter
mm mm
Nominal
Types 1TE, 2TE,
a
size
Type R6 Type R3 Type 1TE Type 2TE Type 3TE Type R6 Type R3
b
3TE
min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
5 4,4 5,2 4,2 5,4 4,5 5,4 10,0 11,6 11,0 12,6 12,0 13,6 10,3 11,9 11,9 13,5
6,3 5,9 6,9 5,6 7,2 6,1 7,0 11,6 13,2 12,6 14,2 13,6 15,2 11,9 13,5 13,5 15,1
8 7,4 8,4 7,2
8,8 7,6 8,5 13,1 14,7 14,1 15,7 16,1 17,7 13,5 15,1 16,7 18,3
10 9,0 10,0 8,7 10,3 9,2 10,1 14,7 16,3 15,7 17,3 17,7 19,3 15,1 16,7 18,3 19,8
12,5 12,1 13,3 11,9 13,5 12,4 13,5 17,7 19,7 18,7 20,7 20,7 22,7 19,0 20,6 23,0 24,6
16 15,3 16,5 15,1 16,7 15,6 16,7 21,9 23,9 22,9 24,9 24,9 26,9 22,2 23,8 26,2 27,8
19 18,2 19,8 18,3 19,9 18,7 19,8 — — 26,0 28,0 28,0 30,0 25,4 27,8 31,0 32,5
25 24,6 26,2 — — 25,1 26,2 — — 32,9 35,9 34,4 37,4 — — 36,9 39,3
31,5 30,8 32,8 — — 31,4 32,9 — — — — 40,8 43,8 — — 42,9 46,0
38 37,1 39,1 — —
— — — — — — 47,6 51,6 — — — —
51 49,8 51,8 — — — — — — — — 60,3 64,3 — — — —
60 58,8 61,2 — — — — — — — — 70,0 74,0 — — — —
80 78,8 81,2 — — — — — — — — 91,5 96,5 — — — —
10
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.