Pneumatic fluid power - Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm - Basic and mounting dimensions

This International Standard establishes a metric series of mounting dimensions required for
interchangeability of commonly used pneumatic cylinders for a maximum working pressure of
1 000 kPa (10 bar).
NOTE This International Standard allows manufacturers freedom of design in metric cylinders and does not
restrict technical development but provides basic guidelines.

Transmissions pneumatiques - Vérins à simple tige, série 1 000 kPa (10 bar), alésages de 8 mm à 25 mm - Dimensions de base et de montage

L'ISO 6432:2015 �tablit une s�rie m�trique de dimensions de montage exig�es pour l'interchangeabilit� dimensionnelle des v�rins pneumatiques d'usage courant, � une pression maximale constante d'utilisation de 1 000 kPa (10 bar).
NOTE La pr�sente Norme internationale laisse aux fabricants toute latitude quant � la conception des v�rins m�triques et ne restreint pas le progr�s technique, mais fournit des orientations g�n�rales.

Fluidna tehnika - Pnevmatika - Enosmerni valji vrste 1000 kPa (10 bar) s premerom od 8 mm do 25 mm - Osnovne in vgradne mere

Ta mednarodni standard določa metrične vrste vgradnih mer, ki so potrebne za medsebojno zamenljivost najpogosteje uporabljenih pnevmatskih valjev za največji delovni tlak 1000 kPa (10 barov).
OPOMBA: Ta mednarodni standard proizvajalcem omogoča svobodo pri načrtovanju metričnih valjev in ne omejuje tehničnega razvoja, temveč podaja osnovne napotke.

General Information

Status
Published
Publication Date
28-Mar-2016
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Mar-2016
Due Date
26-May-2016
Completion Date
29-Mar-2016

Relations

Buy Standard

Standard
ISO 6432:2015 - Pneumatic fluid power -- Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm -- Basic and mounting dimensions
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 6432:2016
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 6432:2015 - Transmissions pneumatiques -- Vérins a simple tige, série 1 000 kPa (10 bar), alésages de 8 mm a 25 mm -- Dimensions de base et de montage
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6432
Second edition
2015-08-15
Pneumatic fluid power — Single rod
cylinders, 1 000 kPa (10 bar) series,
bores from 8 mm to 25 mm — Basic
and mounting dimensions
Transmissions pneumatiques — Vérins à simple tige, série 1 000 kPa
(10 bar), alésages de 8 mm à 25 mm — Dimensions de base et de
montage
Reference number
ISO 6432:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6432:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6432:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 Basic dimensions . 1
4.2 Mounting dimensions . 1
5 Nominal stroke . 2
6 Bore sizes . 2
7 Mounting types . 2
8 Piston rod characteristics . 2
9 Identification statement (reference to this International Standard) . 2
Bibliography . 6
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6432:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3,
Cylinders.
This second edition cancels and replaces the first edition (ISO 6432:1985), which has been technically
revised.
iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 6432:2015(E)

Introduction
In pneumatic fluid power systems, power is transmitted and controlled through a gas under pressure
within a circuit.
One component of such systems is the pneumatic cylinder. This is a device which converts power into
linear mechanical force and motion. It consists of a movable element, i.e. a piston, and a piston
...

SLOVENSKI STANDARD
SIST ISO 6432:2016
01-maj-2016
1DGRPHãþD
SIST ISO 6432:1997
Fluidna tehnika - Pnevmatika - Enosmerni valji vrste 1000 kPa (10 bar) s premerom
od 8 mm do 25 mm - Osnovne in vgradne mere
Pneumatic fluid power - Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm
to 25 mm - Basic and mounting dimensions
Transmissions pneumatiques - Vérins à simple tige, série 1 000 kPa (10 bar), alésages
de 8 mm à 25 mm - Dimensions de base et de montage
Ta slovenski standard je istoveten z: ISO 6432:2015
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST ISO 6432:2016 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 6432:2016

---------------------- Page: 2 ----------------------

SIST ISO 6432:2016
INTERNATIONAL ISO
STANDARD 6432
Second edition
2015-08-15
Pneumatic fluid power — Single rod
cylinders, 1 000 kPa (10 bar) series,
bores from 8 mm to 25 mm — Basic
and mounting dimensions
Transmissions pneumatiques — Vérins à simple tige, série 1 000 kPa
(10 bar), alésages de 8 mm à 25 mm — Dimensions de base et de
montage
Reference number
ISO 6432:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

SIST ISO 6432:2016
ISO 6432:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 6432:2016
ISO 6432:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 Basic dimensions . 1
4.2 Mounting dimensions . 1
5 Nominal stroke . 2
6 Bore sizes . 2
7 Mounting types . 2
8 Piston rod characteristics . 2
9 Identification statement (reference to this International Standard) . 2
Bibliography . 6
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 6432:2016
ISO 6432:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3,
Cylinders.
This second edition cancels and replaces the first edition (ISO 6432:1985), which has been technically
revised.
iv © ISO 2015 – All rig
...

NORME ISO
INTERNATIONALE 6432
Deuxième édition
2015-08-15
Transmissions pneumatiques —
Vérins à simple tige, série 1 000 kPa
(10 bar), alésages de 8 mm à 25 mm —
Dimensions de base et de montage
Pneumatic fluid power — Single rod cylinders, 1 000 kPa (10 bar)
series, bores from 8 mm to 25 mm — Basic and mounting dimensions
Numéro de référence
ISO 6432:2015(F)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6432:2015(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 6432:2015(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Dimensions . 1
4.1 Dimensions générales . 1
4.2 Dimensions de montage . 1
5 Courses nominales . 2
6 Diamètres d’alésage . 2
7 Types de fixation . 2
8 Caractéristiques de la tige de piston . 2
9 Phrase d’identification (Référence à la présente Norme internationale) .2
Bibliographie . 6
© ISO 2015 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 6432:2015(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer
un engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos —
Informations supplémentaires.
L’ISO 6432 a été élaborée par le comité technique ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC 3, Vérins.
Cette deuxième édition annule et remplace la première édition (ISO 6432:1985), qui fait l’objet d’une
révision technique.
iv © ISO 2015 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 6432:2015(F)

Introduction
Dans les systèmes de transmissions pneumatiques, l’énergie est transmise de commandée par un gaz
sous pression circulant dans un circuit.
Un des composants de ces systèmes est le vérin pneumatique. C’est un dispositif qui transforme l’énergie
du fluide en énergie mécanique agissant linéairement. Il est constitué d’un élément mobile, c’est-à-dire
un piston et une tige de piston se déplaçant dans un alésage cylindrique.
Afin de les fixer sur les machines de l’utilisateur, les vérins pneumatiques comprennent, en outre, des
dispositifs dénommés «fixations».
© ISO 2015 – Tous droits réservés v

--
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.