SIST EN IEC 60335-2-58:2025/A11:2025
(Amendment)Household and similar electrical appliances - Safety - Part 2-58: Particular requirements for commercial electric dishwashing machines
Household and similar electrical appliances - Safety - Part 2-58: Particular requirements for commercial electric dishwashing machines
This European Standard deal with the safety of electrically operated dishwashing machines for washing plates, dishes, glassware, cutlery and similar articles, with or without means for water heating or drying, not intended for household use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-58: Besondere Anforderungen für elektrische Spülmaschinen für den gewerblichen Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-58: Règles particulières pour les lave-vaisselle électriques à usage collectif
Gospodinjski in podobni električni aparati - Varnost - 2-58. del: Posebne zahteve za komercialne električne pomivalne stroje - Dopolnilo A11
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2025
Gospodinjski in podobni električni aparati - Varnost - 2-58. del: Posebne zahteve
za komercialne električne pomivalne stroje - Dopolnilo A11
Household and similar electrical appliances - Safety - Part 2-58: Particular requirements
for commercial electric dishwashing machines
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-58:
Besondere Anforderungen für elektrische Spülmaschinen für den gewerblichen
Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-58: Règles particulières
pour les lave-vaisselle électriques à usage collectif
Ta slovenski standard je istoveten z: EN IEC 60335-2-58:2025/A11:2025
ICS:
97.040.40 Pomivalni stroji Dishwashers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60335-2-
58:2025/A11
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2025
ICS 97.040.40
English Version
Household and similar electrical appliances - Safety - Part 2-58:
Particular requirements for commercial electric dishwashing
machines
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-58: Exigences particulières pour les lave-vaisselle ähnliche Zwecke - Teil 2-58: Besondere Anforderungen für
électriques à usage collectif elektrische Spülmaschinen für den gewerblichen Gebrauch
This amendment A11 modifies the European Standard EN IEC 60335-2-58:2025; it was approved by CENELEC on 2025-08-04. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60335-2-58:2025/A11:2025 E
Contents Page
European foreword . 3
1 Modifications to the Introduction . 4
2 Modifications to Clause 1, “Scope” . 4
3 Modifications to Clause 2, “Normative references” . 5
4 Modifications to Clause 3, “Terms and definitions” . 5
5 Modification to Clause 4, “General requirement” . 6
6 Modification to Clause 7, “Marking and instructions” . 6
7 Modification to Clause 11, “Heating” . 8
8 Modification to Clause 13, “Leakage current and electric strength at operating
temperature” . 8
9 Modification to Clause 19, “Abnormal operation” . 8
10 Modification to Clause 20, “Stability and mechanical hazards” . 9
11 Modification to Clause 21, “Mechanical strength” . 9
12 Modification to Clause 22, “Construction” . 9
13 Modification to the Clause 24, “Components” . 11
14 Modification to Clause 25, “Supply connection and external flexible cords” . 11
15 Modification to Clause 27, “Provision for earthing” . 11
16 Modification to Clause 31, “Resistance to rusting” . 12
17 Modification to the annexes . 13
18 Modification to the Bibliography . 21
European foreword
This document (EN IEC 60335-2-58:2025/A11:2025) has been prepared by CLC/TC 61 “Safety of
household and similar electrical appliances”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2026-10-31
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2028-10-31
conflicting with this document have to be
withdrawn
This document is read in conjunction with EN IEC 60335-2-58:2025.
The numbering system for European clauses, subclauses, notes, tables, figures and annexes that are
additional to those in the IEC standard are prefixed with the letter “Z”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For the relationship with EU Legislation, see informative Annex ZZB, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
1 Modifications to the Introduction
Addition:
With European Amendment A11, EN 60335-2-58:2005+A1:2008+A11:2010+A2:2015+A12:2016 is
superseded.
This European Amendment A11, supplements or modifies the corresponding clauses of the standards
below:
— EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019+A15:2021+A16:2023 (Part 1)
— EN IEC 60335-2-58:2025 (Part 2)
Pressurized components incorporated in machines within the scope of this standard are pressure
equipment which is classified no higher than category I of the Pressure Equipment Directive
(2014/68/EU). According to Article 1, item 2.f of the Pressure Equipment Directive, this equipment is
excluded from its scope.
2 Modifications to Clause 1, “Scope”
Add “commercial” before “dishwashing” in the first paragraph.
Delete “plates” in the second paragraph.
Add to the second paragraph before the Note 101:
“These dishwashing machines are designed to be connected to hot and/or cold water supply.
Dishwashing machines making use of steam or hot water for heating purposes are also within the scope
of this document.”
Delete the first list item of Note 102.
Add after the fourth paragraph starting with” The electrical part of appliances….”:
“This document also deals with noise requirements. See Annex ZAA.”
Add the following list item in Note 103:
“— for scrapping of appliances, additional requirements can be necessary.”
Replace the Note 104 with the following:
“
NOTE Z101 This document does not apply to
— appliances designed exclusively for industrial purposes, for example machines used in the food industry for
cleaning receptacles that serve as packaging for final products (e.g. bottle-cleaning machines) and machines
used in manufacturing processes;
— dishwashers that do not form one functional unit, for example where a transportation device transfers the load
from one separate unit to another;
— separately driven transport devices not confined in the appliance;
— appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas);
— commercial electric conveyor dishwashing machines (EN 50416)
— sterilizers and washer-disinfectors used to treat medical materials (EN IEC 61010-2-040).”
3 Modifications to Clause 2, “Normative references”
Delete IEC 61770:2008 and IEC 61770:2008/AMD1:2015.
Add the following:
EN ISO 3744:2010, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane
(ISO 3744:2010)
EN ISO 3746:2010, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Survey method using an enveloping measurement surface over a
reflecting plane (ISO 3746:2010)
EN ISO 4871:2009, Acoustics - Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 9614-2:1996, Acoustics - Determination of sound power levels of noise sources using sound
intensity - Part 2: Measurement by scanning (ISO 9614-2:1996)
EN ISO 11201:2010, Acoustics - Noise emitted by machinery and equipment - Determination of emission
sound pressure levels at a work station and at other specified positions in an essentially free field over a
reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 11202:2010, Acoustics - Noise emitted by machinery and equipment - Determination of
emission sound pressure levels at a work station and at other specified positions applying approximate
environmental corrections (ISO 11202:2010)
EN ISO 11203:2009, Acoustics - Noise emitted by machinery and equipment - Determination of
emission sound pressure levels at a work station and at other specified positions from the sound power
level (ISO 11203:1995)
EN ISO 11688-1:2009, Acoustics - Recommended practice for the design of low-noise machinery and
equipment - Part 1: Planning (ISO/TR 11688-1:1995)
4 Modifications to Clause 3, “Terms and definitions”
3.1 Replacement:
For the purpose of this document, the term “appliance” as used in Part 1 is to be read as “commercial
electric dishwashing machine”.
3.1.9 In the sixth paragraph, replace “Conveyor dishwashers and brush” with “Brush”.
Delete the footnote “ There exists a consolidated …”.
3.5.102 Replace the word “plates” in the first paragraph with the word “dishes”.
3.5.103 Delete the term entry.
Add the following definitions:
“
As impacted by EN ISO 11202:2010/A1:2021.
As impacted by EN ISO 11203:2009/A1:2020.
3.Z101
guard
part of the appliance specially designed to provide protection by means of a physical barrier
3.Z102
operator
person installing, operating, adjusting, maintaining, cleaning or moving the appliance
3.Z103
workstation
place, as defined in the technical documentation of the relevant appliance, where the operator has to be
in attendance to operate, or to adjust, or to control the appliance
EXAMPLE An example is the location where the operator loads the appliance.”
5 Modification to Clause 4, “General requirement”
Replace the text of Part 2 with the following:
“This clause of Part 1 is applicable except as follows:”
Replace the first paragraph with the following:
“Appliances shall be constructed so that they function safely and cause no danger to persons or
surroundings during normal use, even in the event of carelessness, and during installation, adjusting,
maintenance, cleaning, repairing or transportation.”
6 Modification to Clause 7, “Marking and instructions”
7.1 In Part 1, in the sentence starting with “Appliances shall be marked …”, replace the fourth and fifth list
items with the following:
“
— business name and full address of the manufacturer and, where applicable, his authorized
representative;
— model or type reference, serial number, if any, and production year;
NOTE Z101 Production year is the year when the production process is completed. The production year can be
a part of the serial number.”
Add the following new list items in the addition:
“
— the water pressure or range of pressure, in kilopascals (kPa), for the appliances intended to be
connected to a water supply, unless this is indicated in the instruction sheet.
— designation of the appliance. The designation can be a combination of letters and/or numbers and
shall enable to identify the machine as specified in the instructions.”
Delete the Modification starting with “The instruction concerning persons…” up to “… appliance is not
applicable”.
7.12
Delete the paragraph starting with “This appliance can be used by children…” up to “…by children without
supervision”.
Addition:
The front cover of the instructions shall include the substance of the following warning:
CAUTION: Read the instructions before using the appliance.
This wording may be replaced by symbols ISO 7000-0434(2004-01
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.