SIST EN 61300-3-25:2014
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-25: Examinations and measurements - Concentricity of the non-angled ferrules and non-angled ferrules with fibre installed
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-25: Examinations and measurements - Concentricity of the non-angled ferrules and non-angled ferrules with fibre installed
IEC 61300-3-25 describes the procedure to determine the concentricity of the axis of the bore in a non-angled ferrule with the axis of the ferrule, or in the case of non-angled ferrules with fibre installed, to determine the concentricity of the axis of the fibre core with the axis of the ferrule.
/
Dispositifs d’interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d’essais et de mesures -- Partie 3-25: Examens et mesures - Concentricité des férules sans angle et des férules sans angle avec fibre montée
La CEI 61300-3-25:2013 décrit une procédure en vue de déterminer la concentricité de l'axe de l'alésage d'une férule sans angle avec l'axe de la férule, ou dans le cas de férules sans angle avec fibre montée, de déterminer la concentricité de l'axe du coeur de la fibre avec l'axe de férule. Cette deuxième édition annule et remplace la première édition parue en 1997; elle constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - révision de la méthode A en vue d'utiliser un processeur de signaux; - introduction de deux nouvelles annexes (A et B). Mots clés: concentricité de l'axe de l'alésage, férule sans angle
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 3-25. del: Preiskave in meritve - Koncentričnost nekotnih tulk in nekotnih tulk z vstavljenim optičnim vlaknom (IEC 61300-3-25:2013)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61300-3-25:2014
01-marec-2014
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO 3UHLVNDYHLQPHULWYH.RQFHQWULþQRVWQHNRWQLKWXONLQ
QHNRWQLKWXON]YVWDYOMHQLPRSWLþQLPYODNQRP ,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-25: Examinations and measurements - Concentricity
of the non-angled ferrules and non-angled ferrules with fibre installed
/
Dispositifs d’interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d’essais et de mesures -- Partie 3-25: Examens et mesures -
Concentricité des férules sans angle et des férules sans angle avec fibre montée
Ta slovenski standard je istoveten z: EN 61300-3-25:2013
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-3-25:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61300-3-25:2014
---------------------- Page: 2 ----------------------
SIST EN 61300-3-25:2014
EUROPEAN STANDARD
EN 61300-3-25
NORME EUROPÉENNE
December 2013
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61300-3-25:1997
English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 3-25: Examinations and measurements -
Concentricity of the non-angled ferrules and non-angled ferrules with fibre
installed
(IEC 61300-3-25:2013)
Dispositifs d’interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive Bauteile -
Procédures fondamentales d’essais et de Grundlegende Prüf- und Messverfahren --Teil
mesures - 3-25: Untersuchungen und Messungen -
Partie 3-25: Examens et mesures - Konzentrizität der nicht abgewinkelten
Concentricité des férules sans angle et des Ferrulen und der nicht abgewinkelten Ferrulen
férules sans angle avec fibre montée mit eingebauter Faser
(CEI 61300-3-25:2013) (IEC 61300-3-25:2013)
This European Standard was approved by CENELEC on 2013-10-18. CENELEC members are bound to comply with
the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a
national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-
CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-3-25:2013 E
---------------------- Page: 3 ----------------------
SIST EN 61300-3-25:2014
EN 61300-3-25:2013 - 2 -
Foreword
The text of document 86B/3548/CDV, future edition 2 of IEC 61300-3-25, prepared by subcommittee
86B “Fibre optic interconnecting devices and passive components” of IEC/TC 86 "Fibre optics" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-3-25:2013.
The following dates are fixed:
(dop) 2014-07-18
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-10-18
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61300-3-25:1997.
EN 61300-3-25:2013 includes the following significant technical changes with respect to EN 61300-3-
25:1997:
a) reconsideration of method A with the idea of applying a signal processor;
b) introduction of two new annexes (A and B).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-3-25:2013 was approved by CENELEC as a
European Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 61300-3-25:2014
- 3 - EN 61300-3-25:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
ISO 2538 - Geometrical Product Specifications (GPS) - EN ISO 2538 -
Series of angles and slopes on prisms
---------------------- Page: 5 ----------------------
SIST EN 61300-3-25:2014
---------------------- Page: 6 ----------------------
SIST EN 61300-3-25:2014
IEC 61300-3-25
®
Edition 2.0 2013-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures –
Part 3-25: Examinations and measurements – Concentricity of the non-angled
ferrules and non-angled ferrules with fibre installed
Dispositifs d’interconnexion et composants passifs à fibres optiques –
Procédures fondamentales d’essais et de mesures –
Partie 3-25: Examens et mesures – Concentricité des férules sans angle et des
férules sans angle avec fibre montée
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX L
ICS 33.180.20 ISBN 978-2-8322-1104-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61300-3-25:2014
– 2 – 61300-3-25 © IEC:2013
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 General description . 5
3.1 General . 5
3.2 Method A: Ferrule surface reference method (reference test method) . 6
3.3 Method B: Core centre reference method in fibre assembled ferrule . 6
3.4 Method C: Ferrule bore reference method for bare ferrule . 6
4 Apparatus . 6
4.1 Method A . 6
4.2 Method B . 6
4.3 Method C . 7
5 Procedure . 7
5.1 Method A . 7
5.2 Method B . 7
5.3 Method C (only applicable to ferrules without fibre installed) . 8
6 Details to be specified . 9
6.1 Method A . 9
6.2 Method B . 9
6.3 Method C . 9
Annex A (informative) Method to determine the centre of the ferrule bore (bare
ferrule case) using a signal processor . 10
Annex B (informative) Method to determine the fibre core centre using a signal
processor . 11
Figure 1 – Definition of concentricity misalignment . 6
Figure 2 – Example of set-up for concentricity measurement (method A) . 7
Figure 3 – Example of set-up for concentricity measurement (method B) . 8
Figure 4 – Example of set-up for concentricity measurement (method C) . 8
---------------------- Page: 8 ----------------------
SIST EN 61300-3-25:2014
61300-3-25 © IEC:2013 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 3-25: Examinations and measurements – Concentricity of
the non-angled ferrules and non-angled ferrules with fibre installed
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.