SIST EN ISO 4497:2020
(Main)Metallic powders - Determination of particle size by dry sieving (ISO 4497:2020)
Metallic powders - Determination of particle size by dry sieving (ISO 4497:2020)
EN-ISO 4497 specifies a method of determining the particle size distribution of metallic powders by dry sieving into size fractions.The method is applicable to dry, unlubricated metallic powders, but not applicable to powders in which the morphology differs markedly from being equiaxial, for example flake-type powders.The method is not applicable to metallic powders having a particle size wholly or mostly under 45 μm.
Metallpulver - Bestimmung der Teilchengröße durch Trockensiebung (ISO 4497:2020)
Dieses Dokument legt das Verfahren zur Bestimmung der Teilchengrößenverteilung metallischer Pulver durch Trockensiebung in Größenfraktionen fest.
Das Verfahren ist anwendbar auf trockene, gleitmittelfreie Metallpulver, aber nicht auf Pulver, deren Partikelform stark von der Kugelgestalt abweicht, z. B. auf Pulver mit Partikeln in Flockenform.
Das Verfahren ist nicht anwendbar auf metallische Pulver mit einer Teilchengröße, die insgesamt oder überwiegend unter 45 µm liegt.
Poudres métalliques - Détermination de la granulométrie par tamisage à sec (ISO 4497:2020)
Le présent document spécifie une méthode de détermination de la distribution granulométrique des poudres métalliques par tamisage à sec en fractions granulométriques.
La méthode est applicable aux poudres métalliques sèches et non lubrifiées, mais non aux poudres dont la morphologie diffère notablement de l'équiaxialité, par exemple aux poudres en flocons.
La méthode n'est pas applicable aux poudres métalliques de granulométrie inférieure, en totalité ou en partie, à 45 µm.
Kovinski praški - Ugotavljanje velikosti delcev s suhim sejanjem (ISO 4497:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4497:2020
01-julij-2020
Nadomešča:
SIST EN 24497:2000
Kovinski praški - Ugotavljanje velikosti delcev s suhim sejanjem (ISO 4497:2020)
Metallic powders - Determination of particle size by dry sieving (ISO 4497:2020)
Metallpulver - Bestimmung der Teilchengröße durch Trockensiebung (ISO 4497:2020)
Poudres métalliques - Détermination de la granulométrie par tamisage à sec (ISO
4497:2020)
Ta slovenski standard je istoveten z: EN ISO 4497:2020
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 4497:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4497:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 4497:2020
EN ISO 4497
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 77.160 Supersedes EN 24497:1993
English Version
Metallic powders - Determination of particle size by dry
sieving (ISO 4497:2020)
Poudres métalliques - Détermination de la Metallpulver - Bestimmung der Teilchengröße durch
granulométrie par tamisage à sec (ISO 4497:2020) Trockensiebung (ISO 4497:2020)
This European Standard was approved by CEN on 7 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4497:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 4497:2020
EN ISO 4497:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 4497:2020
EN ISO 4497:2020 (E)
European foreword
This document (EN ISO 4497:2020) has been prepared by Technical Committee ISO/TC 119 "Powder
metallurgy" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards
shall be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 24497:1993.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 4497:2020 has been approved by CEN as EN ISO 4497:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 4497:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 4497:2020
INTERNATIONAL ISO
STANDARD 4497
Second edition
2020-04
Metallic powders — Determination of
particle size by dry sieving
Poudres métalliques — Détermination de la granulométrie par
tamisage à sec
Reference number
ISO 4497:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 4497:2020
ISO 4497:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 4497:2020
ISO 4497:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Test equipment. 1
6 Preparation of test portion . 2
6.1 General . 2
6.2 Mass of test portion . 2
7 Procedure. 2
7.1 General . 2
7.2 Sieving time . 2
7.3 Measurement . 3
8 Expression of results . 3
9 Precision . 3
10 Test report . 6
Bibliography . 7
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 4497:2020
ISO 4497:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee
SC 2, Sampling and testing methods for powders (including powd
...
SLOVENSKI STANDARD
oSIST prEN ISO 4497:2019
01-julij-2019
Kovinski praški - Ugotavljanje velikosti delcev s suhim sejanjem (ISO/DIS
4497:2019)
Metallic powders - Determination of particle size by dry sieving (ISO/DIS 4497:2019)
Metallpulver - Bestimmung der Teilchengröße durch Trockensiebung (ISO/DIS
4497:2019)
Poudres métalliques - Détermination de la granulométrie par tamisage à sec (ISO/DIS
4497:2019)
Ta slovenski standard je istoveten z: prEN ISO 4497
ICS:
77.160 Metalurgija prahov Powder metallurgy
oSIST prEN ISO 4497:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 4497:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 4497:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4497
ISO/TC 119/SC 2 Secretariat: SIS
Voting begins on: Voting terminates on:
2019-05-28 2019-08-20
Metallic powders — Determination of particle size by
dry sieving
Poudres métalliques — Détermination de la granulométrie par tamisage à sec
ICS: 77.160
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 4497:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 4497:2019
ISO/DIS 4497:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 4497:2019
ISO/DIS 4497:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
5.1 Calibrated cloth sieves . 1
5.2 Balance . 2
5.3 Brush . 2
6 Preparation of test portion . 2
6.1 General . 2
6.2 Mass of test portion . 2
7 Procedure. 2
7.1 General . 2
7.2 Sieving time . 2
7.3 Measurement . 3
8 Expression of results . 3
9 Precision . 3
10 Test report . 5
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 4497:2019
ISO/DIS 4497:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee
SC 2, Sampling and testing methods for powders (including powders for hardmetals).
This second edition cancels and replaces the first edition (ISO 4497:1983), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Inclusion of a precision statement
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 4497:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 4497:2019(E)
Metallic powders — Determination of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.